Cylinder Head Temperature gauge

Short description: Temperature monitoring device for cylinder heads of an engine

Analog Cylinder Head Temperature gauge

A Cylinder Head Temperature gauge (CHT) measures the cylinder head temperature of an engine. Commonly used on air-cooled engines, the head temperature gauge displays the work that the engine is performing more quickly than an oil or water temperature gauge. As the engine works at high speed or uphill, head temperature will increase quickly. The meter can be digital or analog.

An air-cooled engine requires a steady flow of air for cooling. Most air-cooled engines have thermostats controlling air doors or flaps to help the engine reach operating temperature as quickly as possible. Any failure of the cooling system will cause engine failure via scuffed piston skirts. Air-cooled engines are used in aircraft engine control and other air-cooled engines as in cars and air-cooled motorcycles.[1]

A cylinder from an air-cooled aviation engine, a Continental C85. Notice the rows of fins on both the steel cylinder barrel and the aluminum cylinder head. The fins provide additional surface area for air to pass over the cylinder and absorb heat. Flat-four aircraft engine

The CHT sender usually has a K-type thermocouple that is mounted under the spark plug. The K-type thermocouple is a pair of two dissimilar metals that produce a small voltage signal when heated. The metal closest to the spark plug is called the hot junction and the other, closest to the head, the cold junction. The ring under the spark plug is used to transfer the heat from the plug to the thermocouple. The gauge and cold junction are usually calibrated at room temperature, 72 °F (22 °C). Because the thermocouple is calibrated for room temperature, the gauge readings will only be 100% accurate at that engine compartment temperature. If the engine compartment temperature is colder, the CHT temperature will display higher. If the engine compartment temperature is higher, the reading will be lower. The error can be corrected with a cold-junction compensating thermistor, which measures the temperature at the cold junction so the gauge can adjust the reading. Low budget gauges do not have this compensating thermistor.

## See also

* Timeline of motor and engine technology
* Timeline of heat engine technology
* Engine cooling

## References

1. ↑ National Transportation Safety Board (NTSB), Safety Recommendation A-12-007, Engine cylinder assemblies that fail

* Biermann, A. E. (1941). "The design of fins for air-cooled cylinders" (pdf). Report Nº 726. NACA. https://autouniversum.wordpress.com/2009/06/22/end-of-an-era-the-last-air-cooled-automobile-engines/.
* P V Lamarque, "The design of cooling fins for Motor-Cycle Engines". Report of the Automobile Research Committee, Institution of Automobile Engineers Magazine, March 1943 issue, and also in "The Institution of Automobile Engineers. Proceedings XXXVII, Session 1942-1943, pp 99-134 and 309-312.
* Julius Mackerle, "Air-cooled Automotive Engines", Charles Griffin & Company Ltd., London 1972.
* Biermann, A. E. (1941). "The design of fins for air-cooled cylinders" (pdf). Report Nº 726. NACA. https://autouniversum.wordpress.com/2009/06/22/end-of-an-era-the-last-air-cooled-automobile-engines/.
* P V Lamarque, "The design of cooling fins for Motor-Cycle Engines". Report of the Automobile Research Committee, Institution of Automobile Engineers Magazine, March 1943 issue, and also in "The Institution of Automobile Engineers. Proceedings XXXVII, Session 1942-1943, pp 99-134 and 309-312.
* Julius Mackerle, "Air-cooled Automotive Engines", Charles Griffin & Company Ltd., London 1972.

* v
* t
* e

Aircraft piston engine components, systems and terminology

Piston engines|

| Mechanical
components|

* Camshaft
* Connecting rod
* Crankpin
* Crankshaft
* Cylinder
* Cylinder head
* Gudgeon pin
* Hydraulic tappet
* Main bearing
* Obturator ring
* Oil pump
* Piston
* Piston ring
* Poppet valve
* Pushrod
* Rocker arm
* Sleeve valve
* Tappet

|

Electrical
components|

* Alternator
* Capacitor discharge ignition
* Dual ignition
* Electronic fuel injection
* Generator
* Ignition system
* Magneto
* Spark plug
* Starter

Terminology|

* Air-cooled
* Aircraft engine starting
* Bore
* Compression ratio
* Dead centre
* Engine displacement
* Four-stroke engine
* Horsepower
* Ignition timing
* Manifold pressure
* Mean effective pressure
* Naturally aspirated
* Monosoupape
* Overhead camshaft
* Overhead valve engine
* Rotary engine
* Shock cooling
* Stroke
* Time between overhauls
* Two-stroke engine
* Valve timing
* Volumetric efficiency

Propellers|

| Components|

* Propeller governor
* Propeller speed reduction unit
* Spinner

|

Terminology|

* Autofeather
* Blade pitch
* Constant-speed
* Contra-rotating
* Counter-rotating
* Scimitar
* Single-blade
* Variable-pitch

Engine instruments|

* Annunciator panel
* EFIS
* EICAS
* Flight data recorder
* Glass cockpit
* Hobbs meter
* Tachometer

Engine controls|

* Carburetor heat
* Throttle

Fuel and induction
system|

* Avgas
* Carburetor
* Fuel injection
* Gascolator
* Inlet manifold
* Intercooler
* Pressure carburetor
* Supercharger
* Turbocharger
* Updraft carburetor

Other systems|

* Auxiliary power unit
* Coffman starter
* Hydraulic system
* Ice protection system
* Recoil start

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Cylinder Head Temperature gauge. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:Cylinder_Head_Temperature_gauge&oldid=4123914"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template