Battery nomenclature

Short description: Naming of types of electrical battery

Standard battery nomenclature describes portable dry cell batteries that have physical dimensions and electrical characteristics interchangeable between manufacturers. The long history of disposable dry cells means that many manufacturer-specific and national standards were used to designate sizes, long before international standards were reached. Technical standards for battery sizes and types are set by standards organizations such as International Electrotechnical Commission (IEC) and American National Standards Institute (ANSI). Popular sizes are still referred to by old standard or manufacturer designations, and some non-systematic designations have been included in current international standards due to wide use.

The complete nomenclature for the battery will fully specify the size, chemistry, terminal arrangements, and special characteristics of a battery. The same physically interchangeable cell size may have widely different characteristics; physical interchangeability is not the sole factor in substitution of batteries.

National standards for dry cell batteries have been developed by ANSI, JIS, British national standards, and others. Civilian, commercial, government, and military standards all exist. Two of the most prevalent standards currently in use are the IEC 60086 series and the ANSI C18.1 series. Both standards give dimensions, standard performance characteristics, and safety information.

Modern standards contain both systematic names for cell types that give information on the composition and approximate size of the cells, as well as arbitrary numeric codes for cell size.

## Contents

* 1 History of the IEC standard
* 2 History of the ANSI standard
* 3 IEC battery nomenclature
* 3.1 Primary batteries
* 3.1.1 Battery numbering
* 3.1.2 Electrochemical system
* 3.1.3 Shape
* 3.1.4 Size code
* 3.1.5 Modifiers
* 3.1.6 Battery categories
* 3.2 Secondary batteries
* 3.2.1 Nickel-cadmium and nickel-metal hydride batteries
* 3.2.2 Lithium-ion batteries
* 4 ANSI battery nomenclature
* 4.1 Size and shape codes
* 4.2 System and performance suffix letters
* 5 See also
* 6 References

## History of the IEC standard

The International Electrotechnical Commission (IEC) was established in France in 1906 and co-ordinates development of standards for a wide range of electrical products. The IEC maintains two committees, TC21 established in 1933 for rechargeable batteries, and TC35 established in 1948 for primary batteries, to develop standards.[1] The current designation system was adopted in 1992. Battery types are designated with a letter/number sequence indicating number of cells, cell chemistry, cell shape, dimensions, and special characteristics. Certain cell designations from earlier revisions of the standard have been retained.[2]

The first IEC standards for battery sizes were issued in 1957.[3] Since 1992, International standard IEC 60086 defines an alphanumeric coding system for batteries.[2][4] British standard 397 for primary batteries was withdrawn and replaced by the IEC standard in 1996.[5]

## History of the ANSI standard

Standardization of batteries in the United States started in 1919, when the US National Bureau of Standards published recommended test procedures and standard dimensions of cells.[6] American standards were revised several times during the following decades, as new sizes of cells were introduced and new chemistry developed, including chloride, alkaline, mercury and rechargeable types.

The first American Standards Association (predecessor to ANSI) standard C18 appeared in 1928. It listed cell sizes using a letter code, roughly in order of size from smallest (A) to larger types. The only numerical designation was the 6-inch tall "No. 6" cell. The older "No. 1" through "No. 5" batteries were discontinued, each being 1 to 5 inches high respectively, although the similarly sized Burgess No. 1 (C cell) and No. 2 (D cell) were still produced under that name through the 1950s. Eventually, the No. 6 was phased out by the 1970s and slowly replaced with the 6-volt four-cell battery. The 1934 edition of the C18 standard expanded the nomenclature system to include series and parallel arrays of cells. In 1954, mercury batteries were included in the standard. The 1959 edition identified types suitable for use with transistor radios. In 1967, NEMA took over responsibility for development from the National Bureau of Standards. The 12th edition of C18 began to be harmonized with the IEC standard. Rechargeable batteries were introduced in the C18 standard in 1984, and lithium types were standardized in 1991.

In 1999 the ANSI standards were extensively revised and separate safety standards provided. The current edition of the ANSI standards designates sizes with an arbitrary number, with a prefix letter to designate shape, and with a suffix letter or letters to identify different chemistry, terminals, or other features.

## IEC battery nomenclature

Three different technical committees of IEC make standards on batteries: TC21 (lead-acid), SC21 (other secondary) and TC35 (primary). Each group has published standards relating to the nomenclature of batteries \- IEC 60095 for lead-acid starter batteries, IEC 61951-1 and 61951-2 for Ni-Cd and Ni-MH batteries, IEC 61960 for Li-ion, and IEC 60086-1 for primary batteries.

### Primary batteries

#### Battery numbering

IEC 60086 battery type designation system

Examples of the IEC nomenclature are batteries coded R20, 4R25X, 4LR25-2, 6F22, 6P222/162, CR17345 and LR2616J. The letters and numbers in the code indicate the number of cells, cell chemistry, shape, dimensions, the number of parallel paths in the assembled battery and any modifying letters deemed necessary. A multi-section battery (two or more voltages from the same package) will have a multi-section designation.

Prior to October 1990, round cells were designated with a sequential numeric size code ranging from R06 through to R70, for example R20 is the size of a "D" cell or ANSI"13" size. After October 1990, round cells are systematically identified with a number derived from their diameter and height. Primary cells larger than 100 mm in diameter or height are designated with an oblique "/" between diameter and height.

Examples of IEC battery designations  Designation | Series Cells | System | Shape | Standardized code or diameter code | Diameter modifier | Height code | Height adjustment modifier | Modifier(s) | Parallel strings | Remarks

|
|
|
|
|
|
|
|
|
|

R20 |  |  | R | 20 |  |  |  |  |  | A single zinc-carbon cell, "size 20" which is equivalent to D, or ANSI "13" size
4R25X | 4 |  | R | 25 |  |  |  | X |  | A zinc-carbon lantern battery, consisting of 4 round "size 25" cells in series. Terminated with spring terminals.
4LR25-2 | 4 | L | R | 25 |  |  |  |  | 2 | An alkaline lantern battery, consisting of 2 parallel strings of 4 round "size 25" cells in series
6F22 | 6 |  | F | 22 |  |  |  |  |  | A zinc-carbon rectangular battery, consisting of 6 flat "size 22" cells. Equivalent to a PP3 or transistor battery.
6P222/162 | 6 |  | P | 222 |  | 162 |  |  |  | A zinc-carbon battery, maximum dimensions: length 192 mm, width 113 mm, and height 162 mm. Consisting of 6 cells in series.
CR17345 |  | C | R | 17 |  | 345 |  |  |  | A single-cell round lithium cell, 17 mm diameter, 34.5 mm height
LR2616J |  | L | R | 26 |  | 16 | J |  |  | A single-cell round alkaline battery, 26.2 mm diameter, 1.67 mm height
LR8D425 |  | L | R | 8.5 | D | 425 |  |  |  | A single-cell round alkaline battery, 8.8 mm diameter (8.5 +0.3 for modifier) and 42.5 mm long, AAAA or ANSI "25" size

#### Electrochemical system

The first letter identifies the chemical composition of the battery, which also implies a nominal voltage.

It is common to refer to the negative electrode first in IEC battery definitions.

IEC codes for battery electrochemical systems[7] Letter
code | Negative electrode | Electrolyte | Positive electrode | Nominal
voltage (V) | Maximum open
circuit voltage (V) | Main article

|
|
|
|
|
|

(none) | Zinc | Ammonium chloride, Zinc chloride | Manganese dioxide | 1.5 | 1.725 | Zinc-carbon battery
A | Zinc | Ammonium chloride, Zinc chloride | Oxygen | 1.4 | 1.55 | Zinc-air battery
B | Lithium | Organic electrolyte | Carbon monofluoride | 3.0 | 3.7 | Lithium battery
C | Lithium | Organic electrolyte | Manganese dioxide | 3.0 | 3.7
E | Lithium | Non-aqueous inorganic electrolyte | Thionyl chloride | 3.6 | 3.9
F | Lithium | Organic electrolyte | Iron disulfide | 1.5 | 1.83
G | Lithium | Organic electrolyte | Copper(II) oxide | 1.5 | 2.3
L | Zinc | Alkali metal hydroxide | Manganese dioxide | 1.5 | 1.65 | Alkaline battery

(withdrawn) | Zinc | Alkali metal hydroxide | Mercuric oxide | 1.35 |  | Mercury battery

(withdrawn) | Zinc | Alkali metal hydroxide | Mercuric oxide, manganese dioxide | 1.4 |
P | Zinc | Alkali metal hydroxide | Oxygen | 1.4 | 1.68 | Zinc-air battery
S | Zinc | Alkali metal hydroxide | Silver oxide | 1.55 | 1.63 | Silver-oxide battery
Z | Zinc | Alkali metal hydroxide | Manganese dioxide, nickel oxyhydroxide | 1.5 | 1.78 | Nickel oxyhydroxide battery

Italics indicate a chemical system unlikely to be found in consumer or general-purpose batteries, or withdrawn from the current standard.

#### Shape

LR44 alkaline cell

Shape codes are:

R Round, (coin, button or cylindrical)
P Not round
F Flat (layer built)
S Square (or rectangular or prismatic)

The F and S shape codes are still in use but are not to be used for new battery definitions.

#### Size code

Certain sizes, given by one or two digit numbers, represent standard size codes from previous editions of the standard. Sizes given as 4 or more digits indicate the diameter of the battery and the overall height.

The numbers in the code correlate with the battery dimensions. For batteries with dimensions of < 100 mm the (truncated) diameter in millimetres, followed by the height in tenths of a millimetre; for batteries with a single dimension ≥ 100 mm the diameter in millimetres, then a slash (/) followed by the height in millimetres.

As well as the recommended size code definitions there are also ten modifying suffix letters that can be added to the end of the specific size code. These run from A to L (omitting F and I) and depending on the largest dimension of the battery can either signify 0.0 – 0.9 mm maximum dimensions or 0.00 – 0.09 mm maximum dimensions with A being 0.0 or 0.00 and L being 0.9 or 0.09.

For flat cells the diameter code is given as the diameter of a circle circumscribed around the whole cell's area.

Standardized size codes for round batteries which do not follow the current nomenclature but have been retained for ease of use are given by a one or two digit number following the R. These include but are not limited to: [8]

IEC size codes for round batteries  Number
code | Nominal
diameter | Nominal
height | Common name

|
|
|

R25 | 32 | 91 | F
R20 | 34.2 | 61.5 | D
R14 | 26.2 | 50.0 | C
R6 | 14.5 | 50.5 | AA
R1 | 12.0 | 30.2 | N
R03 | 10.5 | 44.5 | AAA

Round button batteries also carry two-digit size codes such as R44, see the button battery table for typical dimensions. Other round, flat, and square sizes have been standardized but are used mostly for components of multi-cell batteries.

Error creating thumbnail: Unable to save thumbnail to destinationAssorted sizes of button and coin cells, including alkaline and silver oxide chemistries. Four rectangular 9 V batteries are also shown, for size comparison. Enlarge to see the button and coin cell size code markings.

The following is a partial list of IEC standard recommended diameter and height codes for round cells:

IEC recommended round cell diameter and height codes  Number
code | Maximum
diameter | Maximum
height

|
|

4 | 4.8 |
5 | 5.8 |
6 | 6.8 |
7 | 7.9 |
9 | 9.5 |
10 | 10.0 |
11 | 11.6 |
12 | 12.5 | 1.20
16 | 16 | 1.60
20 | 20 | 2.00
23 | 23 |
24 | 24.5 |
25 |  | 2.50
30 |  | 3.00
36 |  | 3.60
50 |  | 5.00

#### Modifiers

After the package size code(s), additional letters may optionally appear. Terminal styles and variants of the same battery can be designated with the letters X or Y. Performance levels may also be designated with a C, P, S, CF, HH, or HB or other letter suffixes. An appended letter "W" states that this battery complies with all the requirements of the IEC 60086-3 standard for watch batteries, such as dimensional tolerance, chemical leakage, and test methods.

#### Battery categories

IEC nomenclature classifies batteries according to their general shape and overall physical appearance. These categories, however, are not identified in the IEC battery nomenclature:[9][10]

* Category 1: Cylindrical cells with protruding positive and recessed or flat negative terminals. The positive terminal shall be concentric with the cell overall. The total height of the cell is not necessarily the same as the total distance between terminals (This accounts for nubs, recesses and battery casings). The cell casing is insulated. E.g. R1 & LR8D425
* Category 2: Cylindrical cells with protruding positive and protruding or flat negative terminals. The total height of the cell is the same as the total distance between terminals. The cell casing is insulated. E.g. CR14250, LR61
* Category 3: Cylindrical cells with flat positive and negative terminals. The total height of the cell is not necessarily the same as the total distance between terminals (This accounts for any protuberances from the negative terminal). The cell casing is in connection with the positive terminal. No part of the cell is allowed to protrude from the positive terminal surface. E.g. CR11108, LR9
* Category 4: Cylindrical cells with a protruding flat negative terminal. The total height of the cell is the same as the total distance between terminals. The cell casing is the positive terminal and it is recommended that the outer surface is used for positive connection even though it is possible from the base. No part of the cell is allowed to protrude from the positive terminal surface. E.g. LR44, CR2032
* Category 5: Cylindrical batteries which fit none of the other categories. E.g. R40, 8LR23
* Category 6: Non-cylindrical batteries. E.g. 3R12, 4R25, 6F22

### Secondary batteries

####  Nickel-cadmium and nickel-metal hydride batteries

Nickel-cadmium and Nickel-metal hydride batteries follow a similar rule as the system above;[11][12] especially cylindrical cells designed to be dimensionally interchangeable with primary batteries use the same designation as the primary batteries, the codes for electrochemical systems as below.

Letter
code | Negative electrode | Positive electrode | Nominal
voltage (V) | Main article

|
|
|
|

H | Hydrogen-absorbing alloy | Nickel oxide | 1.2 | Nickel-metal hydride battery
K | Cadmium | Nickel oxide | 1.2 | Nickel-cadmium battery

All other cells use the following system:

* Small prismatic cells: KF or HF followed by maximum width in mm / maximum thickness in mm / maximum height in mm. E.g. KF 18/07/49
* Cylindrical cells: KR or HR followed by a letter indicating discharge rate (L, M, H or X for low, medium, high and very high, respectively); then another letter may be added to indicate use at elevated temperatures (T or U) or rapid charge (R); then maximum diameter in mm / maximum height in mm. E.g. KRL 33/62, HRHR 23/43
* Button cells: KB or HB followed by maximum diameter in tenths of mm / maximum height in tenths of mm. E.g. KBL 116/055

####  Lithium-ion batteries

IEC 61960 battery type designation system

Lithium-ion batteries have a different rule for naming, which applies both to batteries of multiple cells and single cell. They will be designated as:[13]

N1A1A2A3N2/N3/N4-N5

where N1 denotes number of series connected cells and N5 denotes number of parallel connected cells (only when the number is greater than 1); these numbers only apply to batteries.

A1 indicates the basis of negative electrode phase, where I is for lithium ion and L is for lithium metal or alloy.

A2 indicates the basis of positive electrode phase, and could be C, N, M, V or T for cobalt, nickel, manganese, vanadium and titanium respectively.

A3 is for the shape of the cell; either R for cylinder or P for prism.

N2 is the maximum diameter (in case of cylindrical cells) or thickness (prismatic cells) in mm.

N3 is only used for prismatic cells to denote the maximum width in mm.

N4 is the maximum overall height in mm.

(For any of the lengths above, if the dimension is smaller than 1 mm it can be written as tN, where N is tenths of mm)

E.g. ICR19/66, ICP9/35/48, 2ICP20/34/70, 1ICP20/68/70-2

## ANSI battery nomenclature

Early editions of the ANSI standard used a letter code to identify the dimensions of the cell. Since at the time there were only carbon-zinc cells, no suffix letters or other notation were required. The letter system was introduced in the 1924 edition of the standard, with letters A through J assigned approximately in order of increasing cell volume, for cells typically manufactured at that time.[6] By 1934, the system had been revised and extended to 17 sizes ranging from NS at ​7⁄16 inch diameter by ​3⁄4 inch height, through size J at ​1 3⁄4 inches diameter by ​5 7⁄8 inches high, to the largest standard cell which retained its old designation of No. 6 and which was ​2 1⁄2 inches in diameter and 6 inches high.

### Size and shape codes

4.5-Volt, D, C, AA, AAA, AAAA, A23, 9-Volt, CR2032 and LR44 cells

The current edition of the standard uses a numerical code to show the cell size. Common round cell sizes are:

ANSI primary cell sizes and equivalent size designations  Number
code | Other name | IEC size  | Example

|
|
|

13 | D | R20  |
14 | C | R14  |
15 | AA | R6  | 15A LR6 SIZE/FORMAT AA 1.5V
24 | AAA | R03  | 24A LR03 SIZE/FORMAT AAA 1.5V
25 | AAAA | R8D425  |

Since these IEC and ANSI battery standards have been harmonized, for example, an R20 cell will have the same dimensions as an ANSI 13 cell.

Flat cells, used as components of multi-cell batteries, have an F prefix and a series of numbers to identify sizes. Coin cells were assigned size codes in the 5000 range.

Secondary cells using systems H and K (nickel-metal hydride and nickel-iron sulfide) have a separate series of size codes, but the cells are dimensionally interchangeable with primary cells.

### System and performance suffix letters

The electrochemical system and performance information is given in suffix letters.

ANSI suffix letters[2] Letter | Significance | IEC system letter

|
|

(none) | carbon-zinc | (none)
A | alkaline | L
AC | alkaline industrial
AP | alkaline photographic
C | carbon-zinc industrial | (none)
CD | carbon zinc industrial, heavy duty
D | carbon zinc, heavy duty
F | carbon zinc, general purpose
H | nickel metal hydride
(rechargeable) | H
K | nickel cadmium
(rechargeable) | K
LB | lithium-carbon monofluoride | B
LC | lithium-manganese dioxide | C
LF | lithium-iron disulfide | F

(withdrawn) | mercuric oxide | M
(withdrawn)
SO | silver oxide | S
SOP | silver oxide photographic
Z | zinc-air | P
ZD  | zinc-air, heavy duty

## See also

* Battery recycling
* Comparison of commercial battery types
* History of the battery
* List of battery sizes
* List of battery types
* Search for the Super Battery (2017 PBS film)

## References

1. ↑ "IEC - About the IEC > History > Techline". http://www.iec.ch/about/history/techline/.
2. ↑ 2.0 2.1 2.2 David Linden, Thomas B. Reddy (ed). Handbook Of Batteries 3rd Edition, McGraw-Hill, New York, 2002 ISBN 0-07-135978-8 chapter 4
3. ↑ M. Barak  Electrochemical power sources: primary and secondary batteries, IET, 1980 ISBN 0-906048-26-5, page 51
4. ↑ Thomas Roy Crompton, Battery reference book, Newnes, 2000 ISBN 0-7506-4625-X, Appendix 2
5. ↑ "British Standards". http://shop.bsigroup.com/en/ProductDetail/?pid=000000000000196342.
6. ↑ 6.0 6.1 Ron Runkles (ed) A Brief History of the Standardization of Portable Cells and Batteries in the United States, American National Standards Institute Accredited Standards Committee C18 on Portable Cells and Batteries, 2002, ANSI Battery Standardization History . Retrieved 2010 Jan 9.
7. ↑ IEC 60086-1 ed10.0
8. ↑ A more complete table is found in the current IEC standard (Table C.1 Annex C) or in Barak 1980 page 53
9. ↑ As indicated in IEC 60086-2 §7
10. ↑ All information is correct to the current version (2011) of IEC 60086 (Parts 1 to 3). As of Thursday 9 June 2011.
11. ↑ IEC61951-1 ed2.1
12. ↑ IEC 61951-2 ed2.0
13. ↑ IEC 61960 ed1.0

* v
* t
* e

List of International Electrotechnical Commission standards

IEC standards|

* IEC 60027
* IEC 60034
* IEC 60038
* IEC 60062
* IEC 60063
* IEC 60068
* IEC 60112
* IEC 60228
* IEC 60269
* IEC 60297
* IEC 60309
* IEC 60320
* IEC 60364
* IEC 60446
* IEC 60559
* IEC 60601
* IEC 60870
* IEC 60870-5
* IEC 60870-6
* IEC 60906-1
* IEC 60908
* IEC 60929
* IEC 60958
* AES3
* S/PDIF
* IEC 61030
* IEC 61131
* IEC 61131-3
* IEC 61158
* IEC 61162
* IEC 61334
* IEC 61346
* IEC 61355
* IEC 61360
* IEC 61400
* IEC 61499
* IEC 61508
* IEC 61511
* IEC 61850
* IEC 61851
* IEC 61883
* IEC 61960
* IEC 61968
* IEC 61970
* IEC 62014-4
* IEC 62056
* IEC 62061
* IEC 62196
* IEC 62262
* IEC 62264
* IEC 62304
* IEC 62325
* IEC 62351
* IEC 62365
* IEC 62366
* IEC 62379
* IEC 62386
* IEC 62455
* IEC 62680
* IEC 62682
* IEC 62700

ISO/IEC standards|

* ISO/IEC 646
* ISO/IEC 2022
* ISO/IEC 4909
* ISO/IEC 5218
* ISO/IEC 6429
* ISO/IEC 6523
* ISO/IEC 7810
* ISO/IEC 7811
* ISO/IEC 7812
* ISO/IEC 7813
* ISO/IEC 7816
* ISO/IEC 7942
* ISO/IEC 8613
* ISO/IEC 8632
* ISO/IEC 8652
* ISO/IEC 8859
* ISO/IEC 9126
* ISO/IEC 9293
* ISO/IEC 9592
* ISO/IEC 9593
* ISO/IEC 9899
* ISO/IEC 9945
* ISO/IEC 9995
* ISO/IEC 10021
* ISO/IEC 10116
* ISO/IEC 10165
* ISO/IEC 10179
* ISO/IEC 10646
* ISO/IEC 10967
* ISO/IEC 11172
* ISO/IEC 11179
* ISO/IEC 11404
* ISO/IEC 11544
* ISO/IEC 11801
* ISO/IEC 12207
* ISO/IEC 13250
* ISO/IEC 13346
* ISO/IEC 13522-5
* ISO/IEC 13568
* ISO/IEC 13818
* ISO/IEC 14443
* ISO/IEC 14496
* ISO/IEC 14882
* ISO/IEC 15288
* ISO/IEC 15291
* ISO/IEC 15408
* ISO/IEC 15444
* ISO/IEC 15445
* ISO/IEC 15504
* ISO/IEC 15511
* ISO/IEC 15693
* ISO/IEC 15897
* ISO/IEC 15938
* ISO/IEC 16262
* ISO/IEC 17024
* ISO/IEC 17025
* ISO/IEC 18000
* ISO/IEC 18004
* ISO/IEC 18014
* ISO/IEC 19752
* ISO/IEC 19757
* ISO/IEC 19770
* ISO/IEC 19788
* ISO/IEC 20000
* ISO/IEC 21000
* ISO/IEC 21827
* ISO/IEC 23000
* ISO/IEC 23003
* ISO/IEC 23008
* ISO/IEC 23270
* ISO/IEC 23360
* ISO/IEC 24707
* ISO/IEC 24727
* ISO/IEC 24744
* ISO/IEC 24752
* ISO/IEC 26300
* ISO/IEC 27000
* ISO/IEC 27000-series
* ISO/IEC 27002
* ISO/IEC 27040
* ISO/IEC 29119
* ISO/IEC 33001
* ISO/IEC 38500
* ISO/IEC 42010
* ISO/IEC 80000

Related|

* International Electrotechnical Commission

0.00

(0 votes)

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Physics:Battery_nomenclature&oldid=3850151"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template