Boundary layer suction

Boundary layer suction[1] is a boundary layer control technique in which an air pump is used to extract the boundary layer at the wing[2] or the inlet of an aircraft. Improving the air flow can reduce drag. Improvements in fuel efficiency have been estimated as high as 30%.

## Contents

* 1 The boundary layer
* 2 Use of suction
* 3 See also
* 4 References
* 5 External links

## The boundary layer

The air molecules at the surface of a wing are effectively stationary (see the no-slip condition). If the flow is smooth, known as laminar flow, the velocity of the air increases steadily as measurements are taken further away from the surface. However the smooth flow is often disturbed by the boundary layer breaking away from the surface and creating a low pressure region immediately behind the airfoil (see flow separation). This low pressure region results in increased overall drag. Attempts have been made over the years to delay the onset of this flow separation by careful design and smooth surfaces.

## Use of suction

As flow separation results from the velocity deficit that is characteristic of boundary layers, suction attempts to remove the boundary layer from the surface before it can separate. The technology was first developed by Werner Pfenninger in the Second World War and has been researched almost continuously since. In the 1960s, NASA experimented with this concept with the Northrop X-21, a converted Douglas WB-66D. In the 1990s, tests were done by NASA with an F-16XL.[3]

Research is going on for its use in gliders at the Technical University of Delft. However, about 500 watts of power would be needed to drive the pumps which would mean covering the glider with solar panels and would increase the cost greatly.[citation needed]}

## See also

* The pusher configuration is an alternative way to re-energize the boundary layer, but is only used on the fuselage.
* NASA F-16XL research aircraft
* Vortex generator
* Aerodynamics
* Boundary layer control
* Circulation control wing
* Turbulator

## References

1. ↑ Huang, L.; Huang, P. G.; LeBeau, R. P.; Hauser, T. (1 September 2004). "Numerical Study of Blowing and Suction Control Mechanism on NACA0012 Airfoil". Journal of Aircraft 41 (5): 1005–1013. doi:10.2514/1.2255. ISSN 0021-8669.
\- Yousefi, Kianoosh; Saleh, Reza; Zahedi, Peyman (1 April 2014). "Numerical study of blowing and suction slot geometry optimization on NACA 0012 airfoil". Journal of Mechanical Science and Technology 28 (4): 1297–1310. doi:10.1007/s12206-014-0119-1. ISSN 1738-494X. http://hal.archives-ouvertes.fr/hal-01590680/file/article.pdf.
2. ↑ Yousefi, Kianoosh; Saleh, Reza (1 June 2015). "Three-dimensional suction flow control and suction jet length optimization of NACA 0012 wing". Meccanica 50 (6): 1481–1494. doi:10.1007/s11012-015-0100-9. ISSN 0025-6455. http://hal.archives-ouvertes.fr/hal-01590679/file/article.pdf.
3. ↑ Marshall, Laurie A. (December 1999). "Boundary-Layer Transition Results From the F-16XL-2 Supersonic Laminar Flow Control Experiment". NASA. http://www.nasa.gov/centers/dryden/pdf/88653main_H-2382.pdf.

## External links

* DGflugzeugbau article
* combination of vortex generator with suction

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Boundary layer suction. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Physics:Boundary_layer_suction&oldid=2619898"