Weir

A weir /wɪər/ or low-head dam is a barrier across the width of a body of water that alters the flow characteristics of water and usually results in a change in the height of the water level. Weirs are used to control the flow of water for rivers, outlets of lakes, ponds, and reservoirs, industrial discharge, and drainage control structures. There are many weir designs, but commonly water flows freely over the top of the weir crest before cascading down to a lower level. There is no single definition as to what constitutes a weir.

Weir can also refer to the skimmer found in most in-ground swimming pools, which controls the flow of water pulled into the filtering system.

## Contents

* 1 Etymology
* 2 Function
* 2.1 Flow measurement
* 2.2 Flow over a V-notch weir
* 2.3 Control of invasive species
* 2.4 Watermills
* 2.5 Flood control and altering river conditions
* 3 Issues
* 3.1 Ecology
* 3.2 Fish migration
* 3.3 Safety
* 4 Common types
* 4.1 Broad-crested
* 4.2 Compound
* 4.3 V-notch
* 4.4 Polynomial
* 5 See also
* 6 References
* 6.1 Citations
* 6.2 Works cited
* 7 Further reading
* 8 External links

## Etymology

The word likely originated from Middle English were, Old English wer, a derivative of the root of the verb werian, meaning "to defend, dam".[1][2] The German cognate is Wehr, which means the same as English weir.

## Function

The broad crested weir at the Thorp grist mill in Thorp, Washington, US

Commonly, weirs are used to prevent flooding, measure water discharge,[3] and help render rivers more navigable by boat. In some locations, the terms dam and weir are synonymous.

A common distinction between dams and weirs is that water may flow through both (controlling flow and often turning turbines in the case of a dam), it only flows over a weir. Thus many dams have an accompanying spillway, lower than the crest of the dam, to release water in excess of its capacity to retain or regulate its flow.

Water flowing over a spillway at Hoover Dam in Arizona, USA, during the 1983 floods

Weirs can vary in size both horizontally and vertically, with the smallest being only a few centimetres in height whilst the largest may be many metres tall and hundreds of metres long. Some common weir purposes are outlined below.

### Flow measurement

When appropriate conditions are met, weirs allow hydrologists and engineers a simple method of measuring the volumetric flow rate in small to medium-sized streams/rivers or in industrial discharge locations.[4] Since the geometry of the top of the weir is known and all water flows over the weir, the depth of water behind the weir can be converted to a rate of flow. However, this can only be achieved in locations where all water flows over the top of the weir crest, and none escapes elsewise.

A generic discharge calculation can be summarised as

Q = CLHn

where

Q is the volumetric flow rate of fluid (the discharge),
C is the flow coefficient for the structure (on average a figure of 3.33),
L is the width of the crest,
H is the height of head of water over the crest,
n varies with structure (e.g., ​3⁄2 for horizontal weir, ​5⁄2 for V-notch weir).[5][6]

### Flow over a V-notch weir

The flow over a V-notch weir (in ft3/s) is given by the Kindsvater–Shen equation:[7]

Q=8152gCetan⁡θ2(h+k)52,

where

Q is the volumetric flow rate of fluid in ft3/s,
g is the acceleration due to gravity in ft/s2,
Ce is the flow correction factor given in Shen 1981, p. B29, Fig. 12,
θ is the angle of the V-notch weir,
h is the height of the fluid above the bottom of the V-notch,
k is the head correction factor given in Shen 1981, p. B20, Fig 4.

### Control of invasive species

As weirs are a physical barrier, they can impede the longitudinal movement of fish and other animals up and down a river. This can have a negative effect on fish species that migrate as part of their breeding cycle (e.g., salmonids), but it also can be useful as a method of preventing invasive species moving upstream. For example, weirs in the Great Lakes region have helped to prevent invasive sea lamprey from colonising farther upstream.

### Watermills

Mill ponds are created by a weir that impounds water that then flows over the structure. The energy created by the change in height of the water can then be used to power waterwheels and power sawmills, grinding wheels, and other equipment.

### Flood control and altering river conditions

See also: Earth:Floodgate

A sluice gate-based weir at Bray Lock on the River Thames, facing downstream. In the background is the smaller secondary "overspill" weir. Two small boats are also visible held against the overspill weir, having been washed against it during a particularly high discharge as a result of meltwater and subsequent rainfall following the 2018 winter cold wave.

Weirs are commonly used to control the flow rates of rivers during periods of high discharge. Sluice gates (or in some cases the height of the weir crest) can be altered to increase or decrease the volume of water flowing downstream. Weirs for this purpose are commonly found upstream of towns and villages and can either be automated or manually operated. By slowing the rate at which water moves downstream even slightly, a disproportionate effect can be had on the likelihood of flooding. On larger rivers, a weir can also alter the flow characteristics of the waterway to the point that vessels are able to navigate areas previously inaccessible due to extreme currents or eddies. Many larger weirs will have construction features that allow boats and river users to "shoot the weir" and navigate by passing up or down stream without having to exit the river. Weirs constructed for this purpose are especially common on the River Thames, and most are situated near each of the river's 45 locks.[citation needed]

## Issues

During periods of high river flow, this nineteenth century weir of porphyry stone on a creek in the Alps would have significantly more water flowing over it.

### Ecology

Because a weir impounds water behind it and alters the flow regime of the river, it can have an effect on the local ecology. Typically, the reduced river velocity upstream can lead to increased siltation (deposition of fine particles of silt and clay on the river bottom) that reduces the water oxygen content and smothers invertebrate habitat and fish spawning sites. The oxygen content typically returns to normal once water has passed over the weir crest (although it can be hyper-oxygenated), although increased river velocity can scour the river bed causing erosion and habitat loss.

### Fish migration

Weirs can have a significant effect on fish migration.[8] Any weir that exceeds either the maximum height a species can jump or creates flow conditions that cannot be bypassed (e.g., due to excessive water velocity) effectively limits the maximum point upstream that fish can migrate. In some cases this can mean that huge lengths of breeding habitat are lost, and over time this can have a significant impact on fish populations.

In many countries, it is now a legal requirement to build fish ladders into the design of a weir that ensure that fish can bypass the barriers and access upstream habitats. Unlike dams, weirs do not usually prevent downstream fish migration (as water flows over the top and allows fish to bypass the structure in that water), although they can create flow conditions that injure juvenile fish. Recent studies suggest that navigation locks have also potential to provide increased access for a range of biota, including poor swimmers.[9]

### Safety

Even though the water around weirs can often appear relatively calm, they can be extremely dangerous places to boat, swim, or wade, as the circulation patterns on the downstream side—typically called a hydraulic jump—can submerge a person indefinitely. This phenomenon is so well known to canoeists, kayakers, and others who spend time on rivers that they even have a rueful name for weirs: "drowning machines".[10] The Ohio DNR recommends that a victim should "tuck the chin down, draw the knees up to the chest with arms wrapped around them. Hopefully, conditions will be such that the current will push the victim along the bed of the river until swept beyond the boil line and released by the hydraulic."[11] The Pennsylvania State Police also recommends to victims, "curl up, dive to the bottom, and swim or crawl downstream".[12] As the hydraulic jump entrains air, the buoyancy of the water between the dam and boil line will be reduced by upward of 30%, and if a victim is unable to float, escape at the base of the dam may be the only option for survival.

## Common types

There are many different types of weirs and they can vary from a simple stone structure that is barely noticeable, to elaborate and very large structures that require extensive management and maintenance.

* The bridge and weir mechanism at Sturminster Newton on the River Stour, Dorset, UK

* Two weirs on the River Wear in Durham, UK: the lower weir is a compound weir that also has fish ladders to allow fish such as salmon to navigate the weir

* The weir at Hambleden Lock on the River Thames at Hambleden, Buckinghamshire. A broad-crest weir, the public has right of way to cross the river using its walkway.

* A manually operated needle dam-type weir near Revin on the River Meuse, France

* A broad-crest weir in Warkworth, New Zealand

* A complicated series of broad-crest and V-notch weirs at Dobbs Weir in Hertfordshire, UK

### Broad-crested

A broad-crested weir is a flat-crested structure, where the water passes over a crest that covers much or all of the channel width. This is one of the most common types of weir found worldwide.[citation needed]

### Compound

A compound weir is any weir that comprises several different designs into one structure. They are commonly seen in locations where a river has multiple users who may need to bypass the structure. A common design would be one where a weir is broad-crested for much of its length, but has a section where the weir stops or is 'open' so that small boats and fish can traverse the structure.

### V-notch

A notch weir is any weir where the physical barrier is significantly higher than the water level except for a specific notch (often V-shaped) cut into the panel. At times of normal flow all the water must pass through the notch, simplifying flow volume calculations, and at times of flood the water level can rise and submerge the weir without any alterations made to the structure.

### Polynomial

A polynomial weir is a weir that has a geometry defined by a polynomial equation of any order n.[13] In practice, most weirs are low-order polynomial weirs. The standard rectangular weir is, for example, a polynomial weir of order zero. The triangular (V-notch) and trapezoidal weirs are of order one. High-order polynomial weirs are providing wider range of Head-Discharge relationships, and hence better control of the flow at outlets of lakes, ponds, and reservoirs.

## See also

* Crump weir
* Drop structure
* Fishing weir
* Fixed-crest dam
* Flume
* International Control Dam
* Run-of-the-river hydroelectricity

## References

### Citations

1. ↑ "the definition of weir". http://www.dictionary.com/browse/weir.
2. ↑ "Weir". Online Etymology Dictionary. http://www.etymonline.com/index.php?term=weir.
3. ↑ Arif, Muhammad (2019). Power Generation Technologies: An Introduction. Islamabad, Pakistan: Pakistan Institute of Engineering and Applied Sciences (PIEAS). pp. 117. ISBN 978-969-7583-01-0.
4. ↑ Arif, Muhammad (2019). Power Generation Technologies: An Introduction. Pakistan Institute of Engineering and Applied Sciences (PIEAS). pp. 118. ISBN 978-969-7583-01-0.
5. ↑ "Weirs – Flow Rate Measure". http://www.engineeringtoolbox.com/weirs-flow-rate-d_592.html.
6. ↑ "Factors affecting weir flow measurement accuracy". http://www.openchannelflow.com/products/weirs/flow-characteristics/.
7. ↑ Shen 1981, p. B31, Equ 6.
8. ↑ Tummers et al. 2016, pp. 183–194.
9. ↑ Silva et al. 2017, pp. 291–302.
10. ↑ Michael Robinson; Robert Houghtalen. "Dangerous dams". Rhode Island Canoe/Kayak Association (Rhode Island). http://www.ricka-flatwater.org/dams.htm.
11. ↑ Ohio DNR Division of Parks and Watercraft Boating. "Lowhead Dam Safety". watercraft.ohiodnr.gov. http://watercraft.ohiodnr.gov/lowheaddams.
12. ↑ "Archived copy". http://www.post-gazette.com/.media/2/2017/05/23/27754452-e17c-469d-923e-cb4851d248db.jpg. Escaping a low-head dam
13. ↑ Baddour 2008, pp. 260–262.

### Works cited

* Akers, Peter (1978). Weirs and Flumes for Flow Measurement. Wiley. ISBN 978-0471996378. https://archive.org/details/weirsflumesforfl0000unse.
* Baddour, Raouf E. (2008). "Head-Discharge Equation for Sharp-Crested Polynomial Weir". Journal of Irrigation and Drainage Engineering 134 (2): 260–262. doi:10.1061/(ASCE)0733-9437(2008)134:2(260). ISSN 0733-9437. Bibcode: 2008JIDE..134..260B.
* Clemmens, Albert (2010). Water Measurement with Flumes and Weirs. Water Resources Publications, LLC. ISBN 978-1887201544.
* Shen, John (1981). Discharge Characteristics of Triangular-notch Thin-plate Weirs. Washington: United States Government Printing Office. https://pubs.usgs.gov/wsp/1617b/report.pdf.
* Silva, Sergio; Lowry, Maran; Macaya-Solis, Consuelo; Byatt, Barry; Lucas, Martyn C. (2017). "Can navigation locks be used to help migratory fishes with poor swimming performance pass tidal barrages? A test with lampreys". Ecological Engineering 102: 291–302. doi:10.1016/j.ecoleng.2017.02.027. ISSN 0925-8574. Bibcode: 2017EcEng.102..291S.
* Tummers, Jeroen S.; Winter, Emily; Silva, Sergio; O’Brien, Pat; Jang, Min-Ho; Lucas, Martyn C. (2016). "Evaluating the effectiveness of a Larinier super active baffle fish pass for European river lamprey Lampetra fluviatilis before and after modification with wall-mounted studded tiles". Ecological Engineering 91: 183–194. doi:10.1016/j.ecoleng.2016.02.046. ISSN 0925-8574. Bibcode: 2016EcEng..91..183T.

## Further reading

* Chanson, H. (2004). The Hydraulics of Open Channel Flow: An Introduction (2nd ed.). Oxford: Butterworth-Heinemann. ISBN 978-0-7506-5978-9.
* Chanson, Hubert (2007). "Hydraulic Performances of Minimum Energy Loss Culverts in Australia". Journal of Performance of Constructed Facilities 21 (4): 264–272. doi:10.1061/(ASCE)0887-3828(2007)21:4(264). ISSN 0887-3828. https://espace.library.uq.edu.au/view/UQ:84668/UQ84668_OA.pdf.
* Gonzalez, Carlos A.; Chanson, Hubert (2007). "Experimental measurements of velocity and pressure distributions on a large broad-crested weir". Flow Measurement and Instrumentation 18 (3–4): 107–113. doi:10.1016/j.flowmeasinst.2007.05.005. ISSN 0955-5986. Bibcode: 2007FloMI..18..107G. http://espace.library.uq.edu.au/view/UQ:107673/fmi_07.pdf.
* Henderson, F.M. (1996), Open Channel Flow, New York: MacMillan Company
* McKay, G.R. (1971). "Design of Minimum Energy Culverts." Research Report, Dept of Civil Eng., Univ. of Queensland, Brisbane, Australia, 29 pages & 7 plates.
* Sturm, Terry W. (2010). Open Channel Hydraulics. McGraw-Hill. ISBN 978-0-07-126793-9. https://books.google.com/books?id=cOUiPwAACAAJ.

## External links

* Hydraulics of Minimum Energy Loss (MEL) culverts and bridge waterways (Click "proceed" at the UQ-ITS Advisory webapge)

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Weir. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Earth:Weir&oldid=4121029"