Solar-cell efficiency

Short description: Ratio of energy extracted from sunlight in solar cells

Solar-cell efficiency is the portion of energy in sunlight that is converted into electricity by a solar cell. Efficiency, in combination with latitude and weather, determine the energy output of a solar system.

As of 2024, the record for solar cell efficiency was 47.6%, set in May 2022 by Fraunhofer ISE, with a III-V four-junction concentrating photovoltaic (CPV) cell.[1][2] The record in real-world conditions is held by NREL, which developed triple junction cells with a tested efficiency of 39.5%.[3][4]

Commercial solar modules may exceed 24% efficiency.[5][6] As of 2025,[7] the best reached 24.5%,[8] typically lower than their cells in isolation. The most efficient mass-produced solar modules have power density values of 175 W/m2 (16.22 W/ft2).[9]

In 2026 using triple III-V germanium cells and shingled matrix technology to interconnect cells, Fraunhofer achieved efficiency of 34.4%. An important innovation was the use of direct cell-to-cell contact, eliminating traditional solder-coated copper ribbons and the resulting shading of active cell areas.[10]

Schematic of charge collection by solar cells. Light transmits through transparent conducting electrode creating electron hole pairs, which are collected by both the electrodes. The absorption and collection efficiencies of a solar cell depend on the design of transparent conductors and active layer thickness.[11]

Several factors affect conversion efficiency, including its reflectance, thermodynamic efficiency, charge carrier separation efficiency, charge carrier collection efficiency and conduction efficiency values.[12][11] Because these parameters are difficult to directly measure, other parameters are measured instead, including quantum efficiency, open-circuit voltage (VOC) ratio, and § Fill factor. Reflectance losses are accounted for by the quantum efficiency value, as they affect external quantum efficiency. Recombination losses are accounted for by these factors. Resistive losses are predominantly accounted for by the fill factor value, but also contribute to the others.

Depending on construction, photovoltaic modules can produce electricity from a range of frequencies of light, but usually cannot cover the entire solar radiation range (specifically, ultraviolet, visible, infrared and low or diffused light). Hence, much of the incident sunlight energy is not processed by solar modules. Theoretically, sunlight could be split into wavelength bands (each a different color), each directed onto cells tuned to those ranges that would convert that band more efficiently.[13]

## Contents

* 1 History
* 2 Factors affecting energy efficiency
* 2.1 Thermodynamic-efficiency limit and infinite-stack limit
* 2.2 Ultimate efficiency
* 2.3 Quantum efficiency
* 2.4 Maximum power point
* 2.5 Fill factor
* 3 Measurement
* 4 Other factors affecting output
* 5 Comparison
* 5.1 Energy payback
* 6 Technical methods of improving efficiency
* 6.1 Choosing optimum transparent conductor
* 6.2 Promoting light scattering
* 6.3 Anti-reflective coatings and textures
* 6.4 Radiative cooling
* 6.5 Rear surface passivation
* 6.6 Thin film materials
* 6.7 Tandem cells
* 7 See also
* 8 References
* 9 External links

## History

Reported timeline of research solar cell energy conversion efficiencies since 1976 (National Renewable Energy Laboratory)

Until 2024 the record was 47.1%, set in 2019 by multi-junction concentrator solar cells developed at National Renewable Energy Laboratory (NREL), Golden, Colorado, USA,[14] which was set in lab conditions, under extremely concentrated light.

In early 2026, Fraunhofer ISE announceed a 34.2% efficient Template:Convert abbreviated module. The module used triple III-V germanium cells. The unit was an adaptation of its space cell to the terrestrial solar spectrum.[10]

## Factors affecting energy efficiency

The factors affecting energy conversion efficiency were expounded in a landmark paper by William Shockley and Hans Queisser in 1961.[15] See Shockley–Queisser limit for more detail.

### Thermodynamic-efficiency limit and infinite-stack limit

Main article: Physics:Thermodynamic efficiency limit

The Shockley–Queisser limit for the efficiency of a single-junction solar cell under unconcentrated sunlight at 273 K. This calculated curve uses actual solar spectrum data, and therefore the curve is wiggly from IR absorption bands in the atmosphere. This efficiency limit of ~34% can be exceeded by multijunction solar cells.

If one has a source of heat at temperature Ts and cooler heat sink at temperature Tc, the maximum theoretically possible value for the ratio of work (or electric power) obtained to heat supplied is 1-Tc/Ts, given by a Carnot heat engine. If we take 6000 K for the temperature of the sun and 300 K for ambient conditions on earth, this comes to 95%.[16]

In 1981, Alexis de Vos and Herman Pauwels showed that this is achievable with a stack of an infinite number of cells with band gaps ranging from infinity (the first cells encountered by the incoming photons) to zero, with a voltage in each cell very close to the open-circuit voltage, equal to 95% of the band gap of that cell, and with 6000 K blackbody radiation coming from all directions. However, the 95% efficiency thereby achieved means that the electric power is 95% of the net amount of light absorbed – the stack emits radiation as it has non-zero temperature, and this radiation must be subtracted from the incoming radiation when calculating the amount of heat being transferred and the efficiency. They also considered the more relevant problem of maximizing the power output for a stack being illuminated from all directions by 6000 K blackbody radiation. In this case, the voltages must be lowered to less than 95% of the band gap (the percentage is not constant over all the cells). The maximum theoretical efficiency calculated is 86.8% for a stack of an infinite number of cells, using the incoming concentrated sunlight radiation.[17] When the incoming radiation comes only from an area of the sky the size of the sun, the efficiency limit drops to 68.7%.[18]

### Ultimate efficiency

Normal photovoltaic systems however have only one p–n junction and are therefore subject to a lower efficiency limit, called the "ultimate efficiency" by Shockley and Queisser. Photons with an energy below the band gap of the absorber material cannot generate an electron-hole pair, so their energy is not converted to useful output, and only generates heat if absorbed.

For photons with an energy above the band gap energy, only a fraction of the energy above the band gap can be converted to useful output. When a photon of greater energy is absorbed, the excess energy above the band gap is converted to kinetic energy of the carrier combination. The excess kinetic energy is converted to heat through phonon interactions as the kinetic energy of the carriers slows to equilibrium velocity. Traditional single-junction cells with an optimal band gap for the solar spectrum have a maximum theoretical efficiency of 33.16%, the Shockley–Queisser limit.[19]

Solar cells with multiple band gap absorber materials improve efficiency by dividing the solar spectrum into smaller bins where the thermodynamic efficiency limit is higher for each bin.[20]

### Quantum efficiency

Main article: Engineering:Quantum efficiency

When a photon is absorbed by a solar cell it can produce an electron-hole pair. One of the carriers may reach the p–n junction and contribute to the current produced by the solar cell; such a carrier is said to be collected. Or, the carriers recombine with no net contribution to cell current.

Quantum efficiency refers to the percentage of photons that are converted to electric current (i.e., collected carriers) when the cell is operated under short circuit conditions. The two types of quantum that are usually referred to when talking about solar cells are external and internal. External quantum efficiency (EQE) relates to the measurable properties of the solar cell. The "external" quantum efficiency of a silicon solar cell includes the effect of optical losses such as transmission and reflection. Measures can be taken to reduce these losses. The reflection losses, which can account for up to 10% of the total incident energy, can be dramatically decreased using a technique called texturization, a light trapping method that modifies the average light path.[21]

The internal quantum efficiency (IQE) gives insight into the internal material parameters like the absorption coefficient or internal luminescence quantum efficiency.[22] IQE is mainly used to aid the understanding of the potential of a certain material rather than a device.[22] Quantum efficiency is most usefully expressed as a spectral measurement (that is, as a function of photon wavelength or energy). Since some wavelengths are absorbed more effectively than others, spectral measurements of quantum efficiency can yield valuable information about the quality of the semiconductor bulk and surfaces. Quantum efficiency is not the same as overall energy conversion efficiency, as it does not convey information about the fraction of power that is converted by the solar cell.

### Maximum power point

Dust often accumulates on the glass of solar modules - highlighted in this negative image as black dots - which reduces the amount of light admitted to the solar cells

A solar cell may operate over a wide range of voltages (V) and currents (I). By increasing the resistive load on an irradiated cell continuously from zero (a short circuit) to a very high value (an open circuit) one can determine the maximum power point, the point that maximizes V×I; that is, the load for which the cell can deliver maximum electrical power at that level of irradiation. (The output power is zero in both the short circuit and open circuit extremes).

The maximum power point of a solar cell is affected by its temperature. Knowing the technical data of certain solar cell, its power output at a certain temperature can be obtained by P(T)=PSTC+dPdT(Tcell−TSTC), where PSTC is the power generated at the standard testing condition; Tcell is the actual temperature of the solar cell.

A high quality, monocrystalline silicon solar cell, at 25 °C cell temperature, may produce 0.60 V open-circuit (VOC). The cell temperature in full sunlight, even with 25 °C air temperature, is probably close to 45 °C, reducing the open-circuit voltage to 0.55 V per cell. The voltage drops modestly, with this type of cell, until the short-circuit current is approached (ISC). Maximum power (with 45 °C cell temperature) is typically produced with 75% to 80% of the open-circuit voltage (0.43 V in this case) and 90% of the short-circuit current. This output can be up to 70% of the VOC x ISC product. The short-circuit current (ISC) from a cell is nearly proportional to the illumination, while the open-circuit voltage (VOC) may drop only 10% with an 80% drop in illumination. Lower-quality cells have a more rapid drop in voltage with increasing current and could produce only 1/2 VOC at 1/2 ISC. The usable power output could thus drop from 70% of the VOC x ISC product to 50% or even as little as 25%. Vendors who rate their solar cell "power" only as VOC x ISC, without giving load curves, can be seriously distorting their actual performance.

The maximum power point of a photovoltaic varies with incident illumination. For example, accumulation of dust on photovoltaic panels reduces the maximum power point.[23] Recently, new research to remove dust from solar panels has been developed by utilizing electrostatic cleaning systems. In such systems, an applied electrostatic field at the surface of the solar panels causes the dust particles to move in a "flip-flop" manner.[24] Then, due to gravity and the fact that the solar panels are slightly slanted, the dust particles get pulled downward by gravity.[24]

These systems only require a small power consumption and enhance the performance of the solar cells, especially when installed in the desert, where dust accumulation contributes to decreasing the solar panel's performance. Also, for systems large enough to justify the extra expense, a maximum power point tracker tracks the instantaneous power by continually measuring the voltage and current (and hence, power transfer), and uses this information to dynamically adjust the load so the maximum power is always transferred, regardless of the variation in lighting.

### Fill factor

Another defining term in the overall behaviour of a solar cell is the fill factor (FF). This factor is a measure of quality of a solar cell. This is the available power at the maximum power point (Pm) divided by the open circuit voltage (VOC) and the short circuit current (ISC):

FF=PmVOC×ISC=η×Ac×GVOC×ISC.

The fill factor can be represented graphically by the IV sweep, where it is the ratio of the different rectangular areas.[25] The fill factor is directly affected by the values of the cell's series, shunt resistances and diodes losses. Increasing the shunt resistance (Rsh) and decreasing the series resistance (Rs) lead to a higher fill factor, thus resulting in greater efficiency, and bringing the cell's output power closer to its theoretical maximum.[26] Typical fill factors range from 50% to 82%. The fill factor for a normal silicon PV cell is 80%.

## Measurement

Each module is rated by its DC output power under standard test conditions. Power typically ranges from 100 to 365 Watts (W). The size of a module determines its output for a given efficiency - an 8% efficient 230 W module requires twice the area of one 16% efficient.

A module's current-voltage (I-V) curve describes its electrical performance.[27] Manufacturing processes often affect the electrical parameters, even in cells of the same type. Therefore, experimental measurement of the I–V curve enables is required to accurately measure them. Generally, the electrical parameters of photovoltaic modules are measured by indoor tests. However, outdoor testing does not require an expensive artificial light source, does not limit sample size, and requires more homogeneous sample illumination.

Capacity factor of solar panels is limited primarily by geographic latitude and varies significantly depending on cloud cover, dust, day length and other factors. In the United Kingdom, seasonal capacity factor ranges from 2% (December) to 20% (July), with average annual output of 10–11% of capacity, while in Spain the value reaches 18%.[28] The capacity factor for utility-scale PV farms averaged 16.1% in 2019.[29] Overheating reduces efficiency.[30]

## Other factors affecting output

A solar panel with 20% efficiency and an area of 1 m2 produces 200 kWh/yr under Standard Test Conditions while exposed to 1000 W/m2 for 2.74 hours a day. Solar panels absorb sunlight for longer periods/day, but solar irradiance is less than 1000 W/m2 for most of the day. A solar panel produces more when the Sun is high in the sky, but less in cloudy conditions, or when the Sun is low in the sky. The Sun stays lower in winter than in other seasons.

Two location-dependent factors that affect solar PV yield are the dispersion and intensity of solar radiation.[31] The Middle East, Northern Chile, Australia, China, and Southwestern USA have the greatest insolation.[31][32] In a high-yield solar area like central Colorado, which receives annual insolation of 2000 kWh/m2/year,[33] a commercial panel produces ~400 kWh per year. However, in Michigan, which receives only 1400 kWh/m2/year,[33] annual energy yield drops to 280 kWh. At more northerly European latitudes, yields fall further: 175 kWh annual energy yield in southern England under the same conditions.[34]

## Comparison

Main article: Chemistry:Photovoltaics

Energy conversion efficiency is measured by dividing the electrical output by the incident light power. Factors influencing output include spectral distribution, spatial distribution of power, temperature, and resistive load. IEC standard 61215 is used to compare the performance of cells and is designed around standard (terrestrial, temperate) temperature and conditions (STC): irradiance of 1 kW/m2, a spectral distribution close to solar radiation through AM (airmass) of 1.5 and a cell temperature 25 °C. The resistive load is varied until the peak or maximum power point (MPP) is achieved. The power at this point is recorded as Watt-peak (Wp). The same standard is used for measuring the power and efficiency of PV modules.

Air mass affects output. In space, where there is no atmosphere, the spectrum of the Sun is relatively unfiltered. However, on Earth, air filters the incoming light, changing the solar spectrum. The filtering effect ranges from Air Mass 0 (AM0) in space, to approximately Air Mass 1.5 on Earth. Multiplying the spectral differences by the quantum efficiency of the solar cell in question yields the efficiency. Terrestrial efficiencies typically are greater than space efficiencies. For example, a silicon solar cell in space might have an efficiency of 14% at AM0, but 16% on Earth at AM 1.5. Note, however, that the number of incident photons in space is considerably larger, so the solar cell might produce considerably more power in space, despite the lower efficiency as indicated by reduced percentage of the total incident energy captured.

Solar cell efficiencies vary from 6% for amorphous silicon-based solar cells to 44.0% with multiple-junction production cells and 44.4% with multiple dies assembled into a hybrid package.[35][36] Solar cell energy conversion efficiencies for commercially available multicrystalline Si solar cells are around 14–19%.[37] The highest efficiency cells have not always been the most economical – for example a 30% efficient multijunction cell based on exotic materials such as gallium arsenide or indium selenide produced at low volume might well cost one hundred times as much as an 8% efficient amorphous silicon cell in mass production, while delivering only about four times the output.

However, there is a way to "boost" solar power. By increasing the light intensity, typically photogenerated carriers are increased, increasing efficiency by up to 15%. These so-called "concentrator systems" have only begun to become cost-competitive as a result of the development of high efficiency GaAs cells. The increase in intensity is typically accomplished by using concentrating optics. A typical concentrator system may use a light intensity 6–400 times the Sun, and increase the efficiency of a one sun GaAs cell from 31% at AM 1.5 to 35%.

A common method used to express economic costs is to calculate a price per delivered kilowatt-hour (kWh). The solar cell efficiency in combination with the available irradiation has a major influence on the costs, but generally speaking the overall system efficiency is important. Commercially available solar cells (as of 2006) reached system efficiencies between 5 and 19%.

Undoped crystalline silicon devices are approaching the theoretical limiting efficiency of 29.43%.[38] In 2017, efficiency of 26.63% was achieved in an amorphous silicon/crystalline silicon heterojunction cell that place both positive and negative contacts on the back of the cell.[39][40]

### Energy payback

The energy payback time is the recovery time required for generating the energy spent for manufacturing a modern photovoltaic module. A 2008 estimate puts it at from 1 to 4 years[41][42] depending on the module type and location. With a typical lifetime of 20 to 30 years, this means that modern solar cells would be net energy producers, i.e., they would generate more energy over their lifetime than the energy expended in producing them.[41][43][44] Generally, thin-film technologies—despite having comparatively low conversion efficiencies—achieve significantly shorter energy payback times than conventional systems (often < 1 year).[45]

A study published in 2013 found that energy payback time was between 0.75 and 3.5 years with thin film cells being at the lower end and multicrystalline silicon (multi-Si) cells having a payback time of 1.5–2.6 years.[46] A 2015 review assessed the energy payback time and EROI of solar photovoltaics. In this meta study, which uses an insolation of 1,700 kWh/m2/year and a system lifetime of 30 years, mean harmonized EROIs between 8.7 and 34.2 were found. Mean harmonized energy payback time varied from 1.0 to 4.1 years.[47] Crystalline silicon devices achieve on average an energy payback period of 2 years.[41][48]

Like any other technology, solar cell manufacture is dependent on the existence of a complex global industrial manufacturing system. This includes the fabrication systems typically accounted for in estimates of manufacturing energy; the contingent mining, refining and global transportation systems; and other energy intensive support systems including finance, information, and security systems. The difficulty in measuring such energy overhead confers some uncertainty on any estimate of payback times.[49]

## Technical methods of improving efficiency

### Choosing optimum transparent conductor

The illuminated side of some types of solar cells, thin films, have a transparent conducting film to allow light to enter into the active material and to collect the generated charge carriers. Typically, films with high transmittance and high electrical conductance such as indium tin oxide, conducting polymers or conducting nanowire networks are used for the purpose. There is a trade-off between high transmittance and electrical conductance, thus optimum density of conducting nanowires or conducting network structure should be chosen for high efficiency.[11]

### Promoting light scattering

Diagram of the characteristic E-field enhancement profiles experienced in thin photovoltaic films (thickness t_PV) patterned with front features. Two simultaneous optical mechanisms can cause light-trapping: anti-reflection and scattering; and two main spectral regions can be distinguished for each mechanism, at short and long wavelengths, thus leading to the 4 types of absorption enhancement profiles illustrated here across the absorber region. The main geometrical parameter of the photonic structures influencing the absorption enhancement in each profile is indicated by the black arrows.[50]

The inclusion of light-scattering effects in solar cells is a photonic strategy to increase the absorption for the lower-energy sunlight photons (chiefly in near-infrared range) for which the photovoltaic material presents reduced absorption coefficient. Such light-trapping scheme is accomplished by the deviation of the light rays from the incident direction, thereby increasing their path length in the cells' absorber.[51]

Conventional approaches used to implement light diffusion are based on textured rear/front surfaces, but many alternative optical designs have been demonstrated with promising results based in diffraction gratings, arrays of metal or dielectric nano/micro particles, wave-optical micro-structuring, among others.[52][53] When applied in the devices' front these structures can act as geometric anti-reflective coatings, simultaneously reducing the reflection of out-going light.

For instance, lining the light-receiving surface of the cell with nano-sized metallic studs can substantially increase the cell efficiency. Light reflects off these studs at an oblique angle to the cell, increasing the length of the light path through the cell. This increases the number of photons absorbed by the cell and the amount of current generated.[54] The main materials used for the nano-studs are silver, gold, and aluminium. Gold and silver are not very efficient, as they absorb much of the light in the visible spectrum, which contains most of the energy present in sunlight, reducing the amount of light reaching the cell.[54] Aluminium absorbs only ultraviolet radiation, and reflects both visible and infra-red light, so energy loss is minimized. Aluminium can increase cell efficiency up to 22% (in lab conditions).[55]

### Anti-reflective coatings and textures

Anti-reflective coatings are engineered to reduce the sunlight reflected from the solar cells, therefore enhancing the light transmitted into the photovoltaic absorber.[56] This can be accomplished by causing the destructive interference of the reflected light waves, such as with coatings based on the front (multi-)layer composition, and/or by geometric refractive-index matching caused by the surface topography, with many architectures inspired by nature.[57]

For example, the nipple-array, a hexagonal array of subwavelength conical nanostructures, can be seen at the surface of the moth's eyes.[57] It was reported that utilizing this sort of surface architecture minimizes the reflection losses by 25%, converting the additional captured photon to a 12% increase in a solar cell's energy.[57]

The use of front micro-structures, such as those achieved with texturizing or other photonic features, can also be used as a method to achieve anti-reflectiveness, in which the surface of a solar cell is altered so that the impinging light experiences a gradually increasing effective refractive-index when travelling from air towards the photovoltaic material. These surfaces can be created by etching or using lithography. Concomitantly, they promote light scattering effects that further enhance the absorption, particularly of the longer wavelength sunlight photons.[50] Adding a flat back surface in addition to texturizing the front surface further helps to trap the light within the cell, thus providing a longer optical path.

### Radiative cooling

See also: Earth:Passive daytime radiative cooling

An increase in solar cell temperature of approximately 1 °C causes an efficiency decrease of about 0.45%. To prevent this, a transparent silica crystal layer can be applied to solar panels. The silica layer acts as a thermal black body, which emits heat as infrared radiation into space, cooling the cell up to 13 °C.[58] Radiative cooling can thus extend the life of solar cells.[59] Full-system integration of solar energy and radiative cooling is referred to as a combined SE–RC system, which have demonstrated higher energy gain per unit area when compared to non-integrated systems.[60]

### Rear surface passivation

See also: Engineering:Surface passivation

Surface passivation is critical to solar cell efficiency.[61] Many improvements have been made to the front side of mass-produced solar cells, but the aluminium back-surface is impeding efficiency improvements.[62] The efficiency of many solar cells has benefitted by creating so-called passivated emitter and rear cells (PERCs). The chemical deposition of a rear-surface dielectric passivation layer stack that is also made of a thin silica or aluminium oxide film topped with a silicon nitride film helps to improve efficiency in silicon solar cells. This helped increase cell efficiency for commercial Cz-Si wafer material from just over 17% to over 21% by the mid-2010s,[63] and the cell efficiency for quasi-mono-Si to a record 19.9%.

Concepts of the rear surface passivation for silicon solar cells has also been implemented for CIGS solar cells.[64] The rear surface passivation shows the potential to improve the efficiency. Al2O3 and SiO2 have been used as the passivation materials. Nano-sized point contacts on Al2O3 layer[65] and line contacts on SiO2 layer[66] provide the electrical connection of CIGS absorber to the rear electrode Molybdenum. The point contacts on the Al2O3 layer are created by e-beam lithography and the line contacts on the SiO2 layer are created using photolithography. Also, the implementation of the passivation layers does not change the morphology of the CIGS layers.

### Thin film materials

See also: Engineering:Thin-film solar cell

Although not constituting a direct strategy to improve efficiency, thin film materials show a lot of promise for solar cells in terms of low costs and adaptability to existing structures and frameworks in technology.[67] Since the materials are so thin, they lack the optical absorption of bulk material solar cells. Attempts to correct this have been demonstrated, such as light-trapping schemes promoting light scattering.[68] Also important is thin film surface recombination. Since this is the dominant recombination process of nanoscale thin-film solar cells, it is crucial to their efficiency. Adding a passivating thin layer of silicon dioxide could reduce recombination.

### Tandem cells

See also: Physics:Multi-junction solar cell

Tandem solar cells combine two materials to increase efficiency. In 2022 a device was announced that combined multiple perovskite with multiple layers of silicon. Perovskites harvest blue light, while silicon picks up red and infrared wavelengths. The cell achieved 32.5% efficiency.[69]

## See also

* Environmental impact of the energy industry
* Energy efficiency
* Thermodynamic efficiency limit
* Shockley-Queisser limit

## References

1. ↑ Schygulla, Patrick; Beutel, Paul; Heckelmann, Stefan; Höhn, Oliver; Klitzke, Malte; Schön, Jonas; Oliva, Eduard; Predan, Felix et al. (2022). "Quadruple Junction Solar Cell with 47.6 % Conversion Efficiency under Concentration". International Conference on Metal Organic Vapor Phase Epitaxy 2022. https://publica.fraunhofer.de/entities/publication/e2ce1921-d7b8-41df-a037-2d82e399d015/fullmeta.
2. ↑ Helmers, Henning; Höhn, Oliver; Lackner, David; Schygulla, Patrick; Klitzke, Malte; Schön, Jonas; Pellegrino, Carmine; Oliva, Eduard et al. (March 8, 2024). "Advancing solar energy conversion efficiency to 47.6% and exploring the spectral versatility of III-V photonic power converters". Physics, Simulation, and Photonic Engineering of Photovoltaic Devices XIII. SPIE Proceedings. 12881. p. 1288103. doi:10.1117/12.3000352. ISBN 978-1-5106-7022-8. Bibcode: 2024SPIE12881E..03H. https://publica.fraunhofer.de/bitstreams/ec4fb182-ed3e-4aa1-886e-4d67978cd456/download.
3. ↑ Ozdemir, Derya (2022-05-20). "Scientists just broke the record for the highest efficiency solar cell" (in en-US). https://interestingengineering.com/innovation/record-highest-efficiency-solar-cell.
4. ↑ France, Ryan M.; Geisz, John F.; Song, Tao; Olavarria, Waldo; Young, Michelle; Kibbler, Alan; Steiner, Myles A. (2022-05-18). "Triple-junction solar cells with 39.5% terrestrial and 34.2% space efficiency enabled by thick quantum well superlattices". Joule 6 (5): 1121–1135. doi:10.1016/j.joule.2022.04.024. ISSN 2542-4351. Bibcode: 2022Joule...6.1121F.
5. ↑ Ulanoff, Lance (2 October 2015). "Elon Musk and SolarCity unveil 'world's most efficient' solar panel". https://mashable.com/2015/10/02/elon-musk-solarcity-new-solar-panel/.
6. ↑ da Silva, Wilson (17 May 2016). "Milestone in solar cell efficiency achieved". https://www.sciencedaily.com/releases/2016/05/160517121811.htm. "A new solar cell configuration developed by engineers at the University of New South Wales has pushed sunlight-to-electricity conversion efficiency to 34.5% -- establishing a new world record for unfocused sunlight and nudging closer to the theoretical limits for such a device."
7. ↑ National Renewable Energy Laboratory (12 April 2024). "Photovoltaic Module Efficiency Records". https://www.nrel.gov/pv/module-efficiency. "These efficiencies have been verified by independent and internationally recognized testing laboratories such as NREL, AIST, JRC-ESTI, and Fraunhofer ISE."
8. ↑ "SunPower e20 Module". 25 July 2014. http://us.sunpower.com/homes/products-services/solar-panels/e-series/.
9. ↑ "HIT Photovoltaic Module". Sanyo / Panasonic. http://www.panasonic.com/business/pesna/includes/pdf/eco-construction-solution/HIT_Power_220A_Datasheet.pdf.
10. ↑ 10.0 10.1 Shahan, Zachary (2026-06-13). "Most Efficient Solar Module in the World — New Record" (in en-US). https://cleantechnica.com/2026/06/12/most-efficient-solar-module-in-the-world-new-record/.
11. ↑ 11.0 11.1 11.2 Kumar, Ankush (2017-01-03). "Predicting efficiency of solar cells based on transparent conducting electrodes". Journal of Applied Physics 121 (1): 014502. doi:10.1063/1.4973117. ISSN 0021-8979. Bibcode: 2017JAP...121a4502K.
12. ↑ "Photovoltaic Cell Conversion Efficiency Basics". U.S. Department of Energy. http://energy.gov/eere/energybasics/articles/photovoltaic-cell-conversion-efficiency-basics.
13. ↑ Orcutt, Mike. "Managing Light To Increase Solar Efficiency" (in en). MIT Technology Review. https://www.technologyreview.com/s/513671/ultra-efficient-solar-power/.
14. ↑ Geisz, John F.; France, Ryan M.; Schulte, Kevin L.; Steiner, Myles A.; Norman, Andrew G.; Guthrey, Harvey L.; Young, Matthew R.; Song, Tao et al. (April 2020). "Six-junction III–V solar cells with 47.1% conversion efficiency under 143 Suns concentration" (in en). Nature Energy 5 (4): 326–335. doi:10.1038/s41560-020-0598-5. ISSN 2058-7546. Bibcode: 2020NatEn...5..326G. http://www.nature.com/articles/s41560-020-0598-5.
15. ↑ Shockley William; Queisser Hans J (1961). "Detailed Balance Limit of Efficiency of p-n Junction Solar Cells". Journal of Applied Physics 32 (3): 510–519. doi:10.1063/1.1736034. Bibcode: 1961JAP....32..510S. http://jap.aip.org/resource/1/japiau/v32/i3/p510_s1.
16. ↑ Würfel, Peter (2002-04-01). "Thermodynamic limitations to solar energy conversion". Physica E: Low-dimensional Systems and Nanostructures 14 (1): 18–26. doi:10.1016/S1386-9477(02)00355-7. ISSN 1386-9477. https://linkinghub.elsevier.com/retrieve/pii/S1386947702003557.
17. ↑ De Vos, A. (1980). "Detailed balance limit of the efficiency of tandem solar cells". Journal of Physics D: Applied Physics 13 (5): 839–846. doi:10.1088/0022-3727/13/5/018. Bibcode: 1980JPhD...13..839D.
18. ↑ A. De Vos; H. Pauwels (1981). "On the Thermodynamic Limit of Photovoltaic Energy Conversion". Appl. Phys. 25 (2): 119–125. doi:10.1007/BF00901283. Bibcode: 1981ApPhy..25..119D.
19. ↑ Rühle, Sven (2016-02-08). "Tabulated Values of the Shockley–Queisser Limit for Single Junction Solar Cells" (in EN). Solar Energy 130: 139–147. doi:10.1016/j.solener.2016.02.015. Bibcode: 2016SoEn..130..139R.
20. ↑ Cheng-Hsiao Wu; Richard Williams (1983). "Limiting efficiencies for multiple energy-gap quantum devices". J. Appl. Phys. 54 (11): 6721. doi:10.1063/1.331859. Bibcode: 1983JAP....54.6721W.
21. ↑ Verlinden, Pierre; Evrard, Olivier; Mazy, Emmanuel; Crahay, André (March 1992). "The surface texturization of solar cells: A new method using V-grooves with controllable sidewall angles". Solar Energy Materials and Solar Cells 26 (1–2): 71–78. doi:10.1016/0927-0248(92)90126-A. Bibcode: 1992SEMSC..26...71V.
22. ↑ 22.0 22.1 Kirchartz, Thomas; Rau, Uwe (2018). "What Makes a Good Solar Cell?" (in en). Advanced Energy Materials 8 (28). doi:10.1002/aenm.201703385. Bibcode: 2018AdEnM...803385K. https://onlinelibrary.wiley.com/doi/10.1002/aenm.201703385.
23. ↑ A. Molki (2010). "Dust affects solar-cell efficiency". Physics Education 45 (5): 456–458. doi:10.1088/0031-9120/45/5/F03. Bibcode: 2010PhyEd..45..456M.
24. ↑ 24.0 24.1 Kawamoto, Hiroyuki; Guo, Bing (2018-02-01). "Improvement of an electrostatic cleaning system for removal of dust from solar panels" (in en). Journal of Electrostatics 91: 28–33. doi:10.1016/j.elstat.2017.12.002. ISSN 0304-3886. https://www.sciencedirect.com/science/article/pii/S0304388617303169.
25. ↑ "Part II – Photovoltaic Cell I-V Characterization Theory and LabVIEW Analysis Code". Part II – Photovoltaic Cell I-V Characterization Theory and LabVIEW Analysis Code - National Instruments, 10 May 2012, ni.com/white-paper/7230/en/.
26. ↑ Jenny Nelson (2003). The Physics of Solar Cells. Imperial College Press. ISBN 978-1-86094-340-9. http://www.solarfreaks.com/download/file.php?id=281.
27. ↑ Piliougine, M.; Carretero, J.; Mora-López, L.; Sidrach-de-Cardona, M. (2011). "Experimental system for current–voltage curve measurement of photovoltaic modules under outdoor conditions". Progress in Photovoltaics: Research and Applications (Progress in Photovoltaics) 19 (5): 591–602. doi:10.1002/pip.1073.
28. ↑ Mearns, Euan (20 October 2015). "UK Solar PV Vital Statistics" (in en-US). http://euanmearns.com/uk-solar-pv-vital-statistics/.
29. ↑ "Solar PV capacity factor globally 2020" (in en). https://www.statista.com/statistics/799330/global-solar-pv-installation-cost-per-kilowatt/.
30. ↑ Elqady, Hesham I.; El-Shazly, A. H.; Elkady, M. F. (31 October 2022). "Parametric study for optimizing double-layer microchannel heat sink for solar panel thermal management" (in en). Scientific Reports 12 (1): 18278. doi:10.1038/s41598-022-23061-8. ISSN 2045-2322. PMID 36316376. Bibcode: 2022NatSR..1218278E.
31. ↑ 31.0 31.1 Kannan, Nadarajah; Vakeesan, Divagar (2016-09-01). "Solar energy for future world: - A review" (in en). Renewable and Sustainable Energy Reviews 62: 1092–1105. doi:10.1016/j.rser.2016.05.022. ISSN 1364-0321. Bibcode: 2016RSERv..62.1092K. https://www.sciencedirect.com/science/article/pii/S1364032116301320.
32. ↑ Köberle, Alexandre C.; Gernaat, David E. H. J.; van Vuuren, Detlef P. (2015-09-01). "Assessing current and future techno-economic potential of concentrated solar power and photovoltaic electricity generation" (in en). Energy 89: 739–756. doi:10.1016/j.energy.2015.05.145. ISSN 0360-5442. Bibcode: 2015Ene....89..739K. https://www.sciencedirect.com/science/article/pii/S0360544215007690.
33. ↑ 33.0 33.1 Billy Roberts (20 October 2008). "Photovoltaic Solar Resource of the United States". http://www.nrel.gov/gis/images/map_pv_national_lo-res.jpg.
34. ↑ David J. C. MacKay. "Sustainable Energy - without the hot air". http://www.inference.org.uk/withouthotair/c6/page_40.shtml. "Solar photovoltaics: data from a 25-m2 array in Cambridgeshire in 2006"
35. ↑ "Solar Junction Breaks Its Own CPV Conversion Efficiency Record". 2013-12-18. http://cleantechnica.com/2012/10/15/solar-junction-powers-up-cpv-with-new-conversion-efficiency-record/.
36. ↑ "Solar Cell Efficiency World Record Set By Sharp — 44.4%". 28 July 2013. http://cleantechnica.com/2013/06/23/solar-cell-efficiency-world-record-set-by-sharp-44-4/.
37. ↑ Schultz, O.; Mette, A.; Preu, R.; Glunz, S. W. (2007). "Silicon Solar Cells with Screen-Printed Front Side Metallization Exceeding 19% Efficiency". doi:10.24406/publica-fhg-356329. http://publica.fraunhofer.de/documents/N-73521.html.
38. ↑ A. Richter; M. Hermle; S.W. Glunz (October 2013). "Reassessment of the limiting efficiency for crystalline silicon solar cells". IEEE Journal of Photovoltaics 3 (4): 1184–1191. doi:10.1109/JPHOTOV.2013.2270351.
39. ↑ K. Yoshikawa; H. Kawasaki; W. Yoshida (2017). "Silicon heterojunction solar cell with interdigitated back contacts for a photoconversion efficiency over 26%". Nature Energy 2 (5): 17032. doi:10.1038/nenergy.2017.32. Bibcode: 2017NatEn...217032Y.
40. ↑ "New World Record Established for Conversion Efficiency in a Crystalline Silicon Solar Cell". 2017-08-25. https://www.kaneka.co.jp/en/service/news/nr201708252/.
41. ↑ 41.0 41.1 41.2 "What is the Energy Payback for PV?". December 2004. http://www.nrel.gov/docs/fy05osti/37322.pdf.
42. ↑ M. Ito et al. (2008). "A comparative study on cost and life-cycle analysis for 100 MW very large-scale PV (VLS-PV) systems in deserts using m-Si, a-Si, CdTe, and CIS modules". Progress in Photovoltaics: Research and Applications 16: 17–30. doi:10.1002/pip.770.
43. ↑ "Net Energy Analysis For Sustainable Energy Production From Silicon Based Solar Cells". http://alpha.chem.umb.edu/chemistry/ch471/evans files/Net_Energy solar cells.pdf.
44. ↑ Corkish, Richard (1997). "Can Solar Cells Ever Recapture the Energy Invested in their Manufacture?". Solar Progress 18 (2): 16–17. http://www.csudh.edu/oliver/smt310-handouts/solarpan/pvpayback.htm.
45. ↑ K. L. Chopra; P. D. Paulson; V. Dutta (2004). "Thin-film solar cells: An overview Progress in Photovoltaics". Research and Applications 12 (23): 69–92. doi:10.1002/pip.541.
46. ↑ Peng, Jinqing; Lu, Lin; Yang, Hongxing (2013). "Review on lifecycle assessment of energy payback and greenhouse gas emission of solar photovoltaic systems". Renewable and Sustainable Energy Reviews 19: 255–274. doi:10.1016/j.rser.2012.11.035. Bibcode: 2013RSERv..19..255P.
47. ↑ Bhandari, Khagendra P.; Jennifer, M.Collier; Ellingson, Randy J.; Apul, Defne S. (2015). "Energy payback time (EPBT) and energy return on energy invested (EROI) of solar photovoltaic systems: A systematic review and meta-analysis". Renewable and Sustainable Energy Reviews 47: 133–141. doi:10.1016/j.rser.2015.02.057. Bibcode: 2015RSERv..47..133B.
48. ↑ "Highest silicon solar cell efficiency ever reached". ScienceDaily. 24 October 2008. https://www.sciencedaily.com/releases/2008/10/081023100536.htm.
49. ↑ Trainer, FE (2007) "Renewable Energy Cannot Sustain a Consumer Society"
50. ↑ 50.0 50.1 Mendes, Manuel J.; Araújo, Andreia; Vicente, António; Águas, Hugo; Ferreira, Isabel; Fortunato, Elvira; Martins, Rodrigo (2016-08-01). "Design of optimized wave-optical spheroidal nanostructures for photonic-enhanced solar cells" (in en). Nano Energy 26: 286–296. doi:10.1016/j.nanoen.2016.05.038. ISSN 2211-2855. Bibcode: 2016NEne...26..286M. https://www.sciencedirect.com/science/article/pii/S2211285516301604.
51. ↑ Schuster, Christian Stefano; Crupi, Isodiana; Halme, Janne; Koç, Mehmet; Mendes, Manuel João; Peters, Ian Marius; Yerci, Selçuk (2022), "Empowering Photovoltaics with Smart Light Management Technologies", in Lackner, Maximilian; Sajjadi, Baharak; Chen, Wei-Yin (in en), Handbook of Climate Change Mitigation and Adaptation, Cham: Springer International Publishing, pp. 1165–1248, doi:10.1007/978-3-030-72579-2_112, ISBN 978-3-030-72579-2
52. ↑ Mendes, Manuel J.; Sanchez-Sobrado, Olalla; Haque, Sirazul; Mateus, Tiago; Águas, Hugo; Fortunato, Elvira; Martins, Rodrigo (2020-01-01), "Chapter Nine - Wave-optical front structures on silicon and perovskite thin-film solar cells", in Enrichi, Francesco; Righini, Giancarlo C. (in en), Solar Cells and Light Management, Elsevier, pp. 315–354, ISBN 978-0-08-102762-2, https://www.sciencedirect.com/science/article/pii/B9780081027622000094, retrieved 2023-03-09
53. ↑ Ruben, Vargas (2015-10-24). "Intech Solar" (in en-IN). https://intechsolar.vn/.
54. ↑ 54.0 54.1 Mukunth, Vasudevan (24 October 2013). "Improving the efficiency of solar panels". The Hindu. http://www.thehindu.com/sci-tech/science/improving-the-efficiency-of-solar-panels/article5265330.ece.
55. ↑ Hylton, Nicholas; Li, X. F; Giannini, K. H.; Lee, N. J; Ekins-Daukes, N. J.; Loo, J.; Vercruysse, D.; Van Dorpe, P. et al. (7 October 2013). "Loss mitigation in plasmonic solar cells: aluminium nanoparticles for broadband photocurrent enhancements in GaAs photodiodes". Scientific Reports 3: 2874. doi:10.1038/srep02874. PMID 24096686. Bibcode: 2013NatSR...3.2874H.
56. ↑ Gee, Justin. "How to Make Solar Panels More Efficient in 2018 | EnergySage". EnergySage Solar News Feed, EnergySage, 19 Sept. 2017, news.energysage.com/how-to-make-solar-panels-more-efficient/.
57. ↑ 57.0 57.1 57.2 Raut, Hemant Kumar; Ganesh, V. Anand; Nair, A. Sreekumaran; Ramakrishna, Seeram (2011). "Anti-reflective coatings: A critical, in-depth review" (in en). Energy & Environmental Science 4 (10): 3779. doi:10.1039/c1ee01297e. ISSN 1754-5692. http://xlink.rsc.org/?DOI=c1ee01297e.
58. ↑ Zhu, Linxiao; Raman, Aaswath P.; Fan, Shanhui (2015-10-06). "Radiative cooling of solar absorbers using a visibly transparent photonic crystal thermal blackbody" (in en). Proceedings of the National Academy of Sciences 112 (40): 12282–12287. doi:10.1073/pnas.1509453112. ISSN 0027-8424. PMID 26392542. Bibcode: 2015PNAS..11212282Z.
59. ↑ Heo, Se-Yeon; Ju Lee, Gil; Song, Young Min (June 2022). "Heat-shedding with photonic structures: radiative cooling and its potential". Journal of Materials Chemistry C 10 (27): 9915–9937. doi:10.1039/D2TC00318J. https://pubs.rsc.org/en/content/articlelanding/2022/tc/d2tc00318j.
60. ↑ Ahmed, Salman; Li, Zhenpeng; Javed, Muhammad Shahzad; Ma, Tao (September 2021). "A review on the integration of radiative cooling and solar energy harvesting". Materials Today: Energy 21. doi:10.1016/j.mtener.2021.100776. Bibcode: 2021MTEne..2100776A. https://www.sciencedirect.com/science/article/abs/pii/S2468606921001416.
61. ↑ Black, Lachlan E. (2016). New Perspectives on Surface Passivation: Understanding the Si-Al2O3 Interface. Springer. ISBN 978-3-319-32521-7. https://core.ac.uk/download/pdf/156698511.pdf.
62. ↑ "Rear-Surface Passivation Technology for Crystalline Silicon Solar Cells: A Versatile Process for Mass Production". Ieee, IEEE, 2012, www.osapublishing.org/DirectPDFAccess/F1E0036E-C63D-5F6F-EA52FF38B5D1786D_270075/oe-21-S6-A1065.pdf?da=1&id=270075&seq=0&mobile=no.
63. ↑ Black, Lachlan E. (2016). New Perspectives on Surface Passivation: Understanding the Si-Al2O3 Interface. Springer. pp. 1–2. ISBN 978-3-319-32521-7. https://core.ac.uk/download/pdf/156698511.pdf.
64. ↑ Vermang, Bart; Wätjen, Jörn Timo; Fjällström, Viktor; Rostvall, Fredrik; Edoff, Marika; Kotipalli, Ratan; Henry, Frederic; Flandre, Denis (2014). "Employing Si solar cell technology to increase efficiency of ultra-thin Cu(In, Ga)Se2 solar cells". Progress in Photovoltaics: Research and Applications 22 (10): 1023–1029. doi:10.1002/pip.2527. PMID 26300619.
65. ↑ Bose, S.; Cunha, J.M.V.; Borme, J.; Chen, W.C.; Nilsson, N.S.; Teixeira, J.P.; Gaspar, J.; Leitão, J.P. et al. (2019). "A morphological and electronic study of ultrathin rear passivated Cu(In, Ga) Se2 solar cells". Thin Solid Films 671: 77–84. doi:10.1016/j.tsf.2018.12.028. Bibcode: 2019TSF...671...77B. https://zenodo.org/record/4479818.
66. ↑ Bose, Sourav; Cunha, José M. V.; Suresh, Sunil; De Wild, Jessica; Lopes, Tomás S.; Barbosa, João R. S.; Silva, Ricardo; Borme, Jérôme et al. (2018). "Optical Lithography Patterning of SiO2 Layers for Interface Passivation of Thin Film Solar Cells". RRL Solar 2 (12). doi:10.1002/solr.201800212. https://zenodo.org/record/1451691.
67. ↑ Da, Yun, and Yimin Xuan. "Role of Surface Recombination in Affecting the Efficiency of Nanostructured Thin-Film Solar Cells ." Osapublishing, 2013, www.osapublishing.org/DirectPDFAccess/F1E0036E-C63D-5F6F-EA52FF38B5D1786D_270075/oe-21-S6-A1065
68. ↑ Mendes, Manuel J.; Haque, Sirazul; Sanchez-Sobrado, Olalla; Araújo, Andreia; Águas, Hugo; Fortunato, Elvira; Martins, Rodrigo (2018-05-25). "Optimal-Enhanced Solar Cell Ultra-thinning with Broadband Nanophotonic Light Capture" (in English). iScience 3: 238–254. doi:10.1016/j.isci.2018.04.018. ISSN 2589-0042. PMID 30428324. Bibcode: 2018iSci....3..238M.
69. ↑ Irving, Michael (2022-12-20). "Perovskite/silicon tandem solar cell advance breaks efficiency record" (in en-US). https://newatlas.com/energy/perovskite-silicon-tandem-solar-cell-efficiency-record-32-5-percent/.

## External links

| Wikimedia Commons has media related to solar cell.

|

* "How Can We Increase the Efficiency of Solar Panels?". https://www.researchgate.net/publication/239441364.

* v
* t
* e

Photovoltaics

Concepts|

| Technology|

* Photovoltaics
* Photoelectric effect
* Solar insolation
* Solar constant
* Solar cell efficiency
* Quantum efficiency
* Nominal power (Watt-peak)
* Thin-film solar cell
* Multi-junction solar cell
* Third-generation photovoltaic cell
* Solar cell research
* Thermophotovoltaic
* Thermodynamic efficiency limit
* Sun-free photovoltaics
* Polarizing organic photovoltaics

|

Materials|

* List of semiconductor materials
* Crystalline silicon (c-Si)
* Polycrystalline silicon (multi-Si)
* Monocrystalline silicon (mono-Si)
* Cadmium telluride
* Copper indium gallium selenide
* Amorphous silicon (a-Si)

History|

* Growth of photovoltaics
* Timeline of solar cells

Photovoltaic system|

| Solar cells|

* Nanocrystal solar cell
* Organic solar cell
* Quantum dot solar cell
* Hybrid solar cell
* Plasmonic solar cell
* Carbon nanotubes in photovoltaics
* Dye-sensitized solar cell
* Cadmium telluride photovoltaics
* Copper indium gallium selenide solar cells
* Printed solar panel
* Perovskite solar cell

|

System components|

* Solar panel
* Balance of system
* Solar charge controller
* Solar inverter
* Solar micro-inverter
* Solar cable
* Photovoltaic mounting system
* Maximum power point tracker
* Solar tracker
* Solar shingles
* Solar mirror
* Synchronverter

System concepts|

* Perturb and observe method
* Incremental conductance method
* Constant voltage method
* Fill factor
* Concentrated photovoltaics
* Photovoltaic thermal hybrid solar collector
* Space-based solar power

Applications|

| Appliances|

* Solar-powered refrigerator
* Solar air conditioning
* Solar lamp
* Solar charger
* Solar backpack
* Solar tree
* Solar-powered pump
* Solar-powered watch
* Solar Tuki
* Photovoltaic keyboard
* Solar road stud
* Solar cell phone charger
* Solar notebook
* Solar-powered calculator
* Solar-powered fountain
* Solar-powered radio
* Solar-powered flashlight
* Solar-powered fan
* Solar street light
* Solar traffic light

|

Land transport|

* Solar vehicle
* Solar car
* Solar roadway
* Solar golf cart
* The Quiet Achiever
* Sunmobile

Air transport|

* Electric aircraft
* Mauro Solar Riser
* Solar panels on spacecraft
* Solar-Powered Aircraft Developments Solar One
* Gossamer Penguin
* Qinetiq Zephyr
* Solar Challenger

Water transport|

* Solar boat

Solar vehicle racing|

* Solar car racing
* List of solar car teams
* Solar challenges
* World Solar Challenge
* American Solar Challenge
* Formula Sun Grand Prix
* Solar Cup
* Frisian Solar Challenge
* Solar Splash
* South African Solar Challenge
* Tour de Sol
* Hunt-Winston School Solar Car Challenge
* Victorian Model Solar Vehicle Challenge

Generation systems|

| PV power station|

* Grid-connected photovoltaic power system
* List of photovoltaic power stations

|

Individual projects|

* Alamosa photovoltaic power plant
* Beneixama photovoltaic power plant
* Blythe Photovoltaic Power Plant
* Copper Mountain Solar Facility
* Darro Solar Park
* Erlasee Solar Park
* Golmud Solar Park
* Gottelborn Solar Park
* Guadarranque solar power plant
* Köthen Solar Park
* Moura Photovoltaic Power Station
* Olmedilla Photovoltaic Park
* Pocking Solar Park
* Puertollano Photovoltaic Park
* Topaz Solar Farm
* Wyandot Solar Facility

Building-mounted|

* Rooftop photovoltaic power station
* Building-integrated photovoltaics
* Solar Ark
* Strasskirchen Solar Park

By country|

* Australia
* Belgium
* Bulgaria
* Canada
* Chile
* China
* Czech Republic
* France
* Germany
* Greece
* India
* Italy
* Japan
* Netherlands
* Romania
* South Africa
* Spain
* Switzerland
* Thailand
* United Kingdom
* USA

PV companies|

| By country|

* List of countries by photovoltaics production

|

Individual producers|

* First Solar
* Hanwha Q CELLS
* JA Solar
* Motech Solar
* REC
* Sharp
* Solar Frontier
* Solyndra
* Sungen Solar
* Sunpower
* Suntech
* Trina Solar
* Yingli Solar

* Category
* Commons

* v
* t
* e

Solar energy

* Outline
* Timeline
* Index

Concepts|

* The Sun
* Solar irradiance
* Active and passive solar energy

Solar power|

| Thermal|

* Passive solar building design
* Solar water heating
* Solar chimney
* Solar air conditioning
* Thermal mass
* Solar pond

|

Photovoltaics
and related topics|

* Photovoltaic effect
* Solar cell
* Polymer solar cell
* Nanocrystal solar cell
* Photovoltaic module (solar panel)
* Photovoltaic array (and systems)
* Photovoltaic power station
* Floating solar

Concentrated|

* Heliostat
* Solar tracker
* Parabolic trough
* Solar power tower

Experimental
and proposed|

* Solar updraft tower
* Solar-pumped laser
* Thermoelectric generator
* Solar chemical and artificial photosynthesis
* Space-based solar power
* Solar sail
* Magnetic sail
* Solar thermal rocket

By country|

* Australia
* Austria
* Albania
* Belgium
* Brazil
* Canada
* China
* Czech
* Denmark
* Georgia
* Germany
* Greece
* India
* Israel
* Italy
* Japan
* Lithuania
* Mexico
* Morocco
* Myanmar
* Netherlands
* New Zealand
* Pakistan
* Portugal
* Romania
* Saudi Arabia
* Somalia
* South Africa
* Spain
* Thailand
* Turkey
* Ukraine
* United Kingdom
* United States
* Yemen

Distribution
and uses|

| Storage|

* Thermal mass
* Thermal energy storage
* Phase change material
* Grid energy storage

|

Adoption|

* Feed-in tariff
* Net metering
* Financial incentives for photovoltaics
* Costs

Applications|

* Solar water heating
* Solar vehicle
* Electric aircraft
* Electric boat
* Solar balloon

Other applications|

| Agriculture
and horticulture|

* Greenhouse
* Polytunnel
* Row cover
* Solar-powered pump

|

Building|

Passive solar building design

* Building-integrated photovoltaics
* Urban heat island

Lighting|

* Hybrid solar lighting
* Solar lamp
* Solar Tuki
* Light tube
* Daylighting

Process heat|

* Solar pond
* Solar furnace
* Salt evaporation pond

Cooking|

* Solar cooker

Disinfection|

* Solar water disinfection
* Soil solarization

Desalination|

* Solar still
* Desalination

Water heating|

* Solar water heating
* Solar combisystem
* Zero carbon solar controller

See also|

* Photovoltaics topics
* Solar power by country
* Renewable energy sources

* Category
* Commons

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Solar-cell efficiency. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Physics:Solar-cell_efficiency&oldid=4549502"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template