Space elevator

Short description: Proposed type of space transportation system

A space elevator is conceived as a cable fixed to the equator and reaching into space. A counterweight at the upper end keeps the center of mass well above geostationary orbit level. This produces enough upward centrifugal force from Earth's rotation to fully counter the downward gravity, keeping the cable upright and taut. Climbers carry cargo up and down the cable.

File:Space elevator in motion viewed from above north pole.ogv

A space elevator, also referred to as a space bridge, star ladder, and orbital lift, is a proposed type of planet-to-space transportation system,[1] often depicted in science fiction. The main component would be a cable (also called a tether) anchored to the surface and extending into space. An Earth-based space elevator would consist of a cable with one end attached to the surface near the equator and the other end attached to a counterweight in space beyond geostationary orbit (35,786 km altitude). The competing forces of gravity, which is stronger at the lower end, and the upward centrifugal force due to the Earth's rotation (i.e., the inertia of the counterweight that creates a tension on the space side), which is stronger at the upper end, would result in the cable being held up, under tension, and stationary over a single position on Earth. With the tether deployed, climbers (crawlers) could repeatedly climb up and down the tether by mechanical means, releasing their cargo to and from orbit.[2] The design would permit vehicles to travel directly between a planetary surface, such as the Earth's, and orbit, without the use of large rockets.

## Contents

* 1 History
* 1.1 Early concept
* 1.2 Innovations and designs
* 1.3 21st-century advancements
* 2 Materials
* 3 In fiction
* 4 Physics
* 4.1 Apparent gravitational field
* 4.2 Cable section
* 4.3 Cable materials
* 4.4 Cable strength
* 5 Structure
* 5.1 Base station
* 5.2 Cable
* 5.3 Climbers
* 5.4 Powering climbers
* 5.5 Counterweight
* 6 Applications
* 6.1 Launching into deep space
* 6.2 Extraterrestrial elevators
* 7 Construction
* 7.1 Safety issues and construction challenges
* 7.2 Economics
* 8 International Space Elevator Consortium (ISEC)
* 9 Related concepts
* 10 Notes
* 11 See also
* 12 References
* 13 Further reading
* 14 External links

## History

### Early concept

The idea of the space elevator appears to have developed independently in different times and places. The earliest models originated with two Russian scientists in the late nineteenth century. In his 1895 collection Dreams of Earth and Sky,[3] Konstantin Tsiolkovsky envisioned a massive sky ladder to reach the stars as a way to overcome gravity,[4][5][6] although Tsiolkovsky's concept was a tower, supported by the ground in compression, rather than the more recent space elevator concept, which is suspended from above in the form of a strong cable held in tension.

Decades later, in 1960, Yuri Artsutanov independently developed the concept of a "Cosmic Railway", a space elevator tethered from an orbiting satellite to an anchor on the equator, aiming to provide a safer and more efficient alternative to rockets.[7][8][9] In 1966, engineer and oceanographer John D. Isaacs and his colleagues developed the concept of the "Sky-Hook", proposing a satellite in geostationary orbit with a cable extending to Earth.[10][11]

### Innovations and designs

The space elevator concept was reinvented and advanced further in 1975, when Jerome Pearson began studying the idea, inspired by Arthur C. Clarke's 1969 speech before Congress. After working as an engineer for NASA and the Air Force Research Laboratory, he developed a design for an "Orbital Tower", intended to harness Earth's rotational energy to transport supplies into low Earth orbit. In his publication in Acta Astronautica,[12] the cable would be thickest at geostationary orbital altitude, where tension is greatest, and narrowest at the tips to minimize weight. He proposed extending a counterweight to 144,000 kilometers (89,000 miles), as without a large counterweight, the upper cable would need to be longer due to the way gravitational and centrifugal forces change with distance from Earth. His analysis included the Moon's gravity, wind, and movable payloads as factors. Building the elevator would have required thousands of Space Shuttle trips, though material could be transported once a minimum strength strand reached the ground or could be manufactured in space from asteroidal or lunar ore. Pearson's findings, published in Acta Astronautica, caught Clarke's attention and led to technical consultations for Clarke's science fiction novel The Fountains of Paradise (1979),[13] which features a space elevator.[14][15] Pearson also pointed out that the portion of the space elevator beyond geosynchronous orbit will be moving faster than orbital velocity, and hence could be used to launch spacecraft onto interplanetary orbits, using the Earth's rotational energy.[12] A later paper by Pearson pointed out that a space elevator could be built on the moon, to the Earth-moon Lagrange Points EM L1 or EM L2. Such a lunar space elevator would be longer than the Earth space elevator, but would not require as high tensile-strength material.[16][17]

The first gathering of multiple experts who wanted to investigate this alternative to space flight took place at the 1999 NASA conference "Advanced Space Infrastructure Workshop on Geostationary Orbiting Tether Space Elevator Concepts" in Huntsville, Alabama, discussing the issues in making and deploying such a space elevator[4][18] In August 2000, D.V. Smitherman, Jr., published the findings under the title Space Elevators: An Advanced Earth-Space Infrastructure for the New Millennium,[19] concluding that the space elevator could not be built for at least another 50 years due to concerns about the cable's material, deployment, and upkeep.

Bradley Edwards suggested that a paper-thin ribbon of a carbon nanotube composite material could solve the strength of materials issue, due to its high tensile strength and low weight.[20] The proposed wide-thin ribbon-like cross-section shape, instead of earlier circular cross-section concepts, would increase survivability against meteoroid impacts. With support from the NASA Institute for Advanced Concepts (NIAC), his work involved more than 20 institutions and 50 participants.[21]: 2 His Phase II Final Report, in combination with the book The Space Elevator: A Revolutionary Earth-to-Space Transportation System [22] summarized issues in design of a space elevator, including deployment scenario, climber design, power delivery system, orbital debris avoidance, anchor system, surviving atomic oxygen, avoiding lightning and hurricanes by locating the anchor in the western equatorial Pacific, construction costs, construction schedule, and environmental hazards.[2] Additionally, he researched the structural integrity and load-bearing capabilities of space elevator cables, emphasizing their need for high tensile strength and resilience.

### 21st-century advancements

To speed space elevator development, proponents had organized several competitions, similar to the Ansari X Prize, for relevant technologies.[23][24] Among them are Unsolved:Elevator:2010, which organized annual competitions for climbers, ribbons and power-beaming systems from 2005 to 2009, the Robogames Space Elevator Ribbon Climbing competition,[25] as well as NASA's Centennial Challenges program, which, in March 2005, announced a partnership with the Spaceward Foundation (the operator of Elevator:2010), raising the total value of prizes to US$400,000.[26][27] The first European Space Elevator Challenge (EuSEC) to establish a climber structure took place in August 2011.[28]

In 2005, "the LiftPort Group of space elevator companies announced that it will be building a carbon nanotube manufacturing plant in Millville, New Jersey, to supply various glass, plastic, and metal companies with these strong materials. Although LiftPort hopes to eventually use carbon nanotubes in the construction of a 100,000 km (62,000 mi) space elevator, this move will allow it to make money in the short term and conduct research and development into new production methods."[29] Their announced goal was a space elevator launch in 2010. On 13 February 2006, the LiftPort Group announced that, earlier the same month, they had tested a mile of "space-elevator tether" made of carbon-fiber composite strings and fiberglass tape measuring 5 cm (2.0 in) wide and 1 mm (0.039 in) (approx. 13 sheets of paper) thick, lifted with balloons.[30] In April 2019, Liftport CEO Michael Laine admitted little progress had been made on the company's lofty space elevator ambitions, even after receiving more than $200,000 in seed funding. The carbon nanotube manufacturing facility that Liftport announced in 2005 was never built.[31]

In 2007, Unsolved:Elevator:2010 held the 2007 Space Elevator games, which featured US$500,000 awards for each of the two competitions ($1,000,000 total), as well as an additional $4,000,000 to be awarded over the next five years for space elevator-related technologies.[32] No teams won the competition, but a team from MIT entered the first 2-gram (0.07 oz), 100-percent carbon nanotube entry into the competition.[33] Japan held an international conference in November 2008 to draw up a timetable for building the elevator.[34]

In 2012, the Obayashi Corporation announced that it could build a space elevator by 2050 using carbon nanotube technology.[35] The design's passenger climber would be able to reach the level of geosynchronous equatorial orbit (GEO) after an 8-day trip.[36] Further details were published in 2016.[37]

In 2013, the International Academy of Astronautics published a technological feasibility assessment, which concluded that the critical capability improvement needed was the tether material, which was projected to achieve the necessary specific strength within 20 years. The four-year-long study examined multiple facets of space elevator development, including missions, development schedules, financial investments, revenue flow, and benefits. It was reported that it would be possible to operationally survive smaller impacts and avoid larger impacts, with meteors and space debris, and that the estimated cost of lifting a kilogram of payload to GEO and beyond would be $500.[38]: 10–11, 207–208 [39] In 2014, Google X's Rapid Evaluation R&D team began designing a Space Elevator, eventually finding that no one had yet manufactured a perfectly formed carbon nanotube strand longer than a meter. They thus put the project in "deep freeze" and also keep tabs on any advances in the carbon nanotube field.[40]

In 2019, the International Academy of Astronautics published "Road to the Space Elevator Era",[41] a study report summarizing the assessment of the space elevator as of summer 2018. The essence is that a broad group of space professionals gathered and assessed the status of the space elevator development, each contributing their expertise and coming to similar conclusions: that Earth space elevators seem feasible, reinforcing the IAA 2013 study conclusion, and that space elevator development initiation is nearer than most think. This last conclusion is based on a potential process for manufacturing macro-scale single crystal graphene[42] with higher specific strength than carbon nanotubes.

Also in 2019, astrophysicists Penoyre and Sandford proposed an already-feasible elevator design anchored on the moon, running through a Lagrange point, and reaching to earth's geosynchronous orbit[43].

## Materials

One of the most significant challenges in manufacturing a space elevator for Earth is the strength of the materials utilized for its construction. Considering the structure must be designed to be sufficiently strong to hold up not only its own weight but also the payload it may carry, the strength-to-weight ratio, or specific strength, of the elevator's construction material needs to be extremely high.

Since 1959, most ideas for space elevators have focused on purely tensile structures, with the weight of the system held up from above by centrifugal forces. In the tensile concepts, a space tether reaches from a large mass (the counterweight) beyond geostationary orbit to the ground. This structure is held in tension between Earth and the counterweight like an upside-down plumb bob. The cable thickness is tapered based on tension; it has its maximum at a geostationary orbit and the minimum on the ground.

The concept is applicable to other planets and celestial bodies. For locations in the Solar System with weaker gravity than Earth's (such as the Moon or Mars), the strength-to-density requirements for tether materials are not as problematic. Currently available materials (such as Kevlar) are strong and light enough that they could be practical as the tether material for elevators there.[44]

Currently available materials are not sufficiently strong and light enough to make the construction of an Earth space elevator practically feasible in the near future.[45][46][47] Some sources expect that future advances in carbon nanotubes (CNTs) could lead to a practical design.[2][19] [29] Other sources believe that CNTs will never be strong enough.[48][49][50] Possible future alternatives to carbon nanotubes include materials like boron nitride nanotubes, diamond nanothreads,[51][52] and macro-scale single-crystal graphene.[42]

## In fiction

Main article: Unsolved:Space elevators in fiction

In 1979, space elevators were introduced to a broader audience with the simultaneous publication of Arthur C. Clarke's novel, The Fountains of Paradise,[53] in which engineers construct a space elevator on top of a mountain peak in the fictional island country of "Taprobane" (loosely based on Sri Lanka, albeit moved south to the Equator), and Charles Sheffield's first novel, The Web Between the Worlds, also featuring the building of a space elevator. Three years later, in Robert A. Heinlein's 1982 novel Friday, the principal character mentions a disaster at the “Quito Sky Hook” and makes use of the "Nairobi Beanstalk" in the course of her travels.

In Kim Stanley Robinson's 1993 novel Red Mars, colonists build a space elevator on Mars that allows both for more colonists to arrive and also for natural resources mined there to be able to leave for Earth. Larry Niven's book Rainbow Mars describes a space elevator built on Mars. In David Gerrold's 2000 novel, Jumping Off The Planet, a family excursion up the Ecuador "beanstalk" is actually a child-custody kidnapping. Gerrold's book also examines some of the industrial applications of a mature elevator technology.

The concept of a space elevator, called the Beanstalk, is also depicted in John Scalzi's 2005 novel Old Man's War. In a biological version, Joan Slonczewski's 2011 novel The Highest Frontier depicts a college student ascending a space elevator constructed of self-healing cables of anthrax bacilli. The engineered bacteria can regrow the cables when severed by space debris.

In the 2021 science fiction show Foundation, the Galactic Empire has constructed a space elevator called the "Star Bridge" on their home world of Trantor.

The 2023 science fiction film The Wandering Earth 2 features scenes where a functioning space elevator is attacked by terrorists.

## Physics

### Apparent gravitational field

An Earth space elevator cable rotates along with the rotation of the Earth. Therefore, the cable, and objects attached to it, would experience upward centrifugal force in the direction opposing the downward gravitational force. The higher up the cable the object is located, the less the gravitational pull of the Earth, and the stronger the upward centrifugal force due to the rotation, so that more centrifugal force opposes less gravity. The centrifugal force and the gravity are balanced at geosynchronous equatorial orbit (GEO). Above GEO, the centrifugal force is stronger than gravity, causing objects attached to the cable there to pull upward on it. Because the counterweight, above GEO, is rotating about the Earth faster than the natural orbital speed for that altitude, it exerts a centrifugal pull on the cable and thus holds the whole system aloft.

The net force for objects attached to the cable is called the apparent gravitational field. The apparent gravitational field for attached objects is the (downward) gravity minus the (upward) centrifugal force. The apparent gravity experienced by an object on the cable is zero at GEO, downward below GEO, and upward above GEO.

The apparent gravitational field can be represented this way:[54]: Table 1

The downward force of actual gravity decreases with height: gr=−GM/r2

The upward centrifugal force due to the planet's rotation increases with height: a=ω2r

Together, the apparent gravitational field is the sum of the two:

g=−GMr2+ω2r

where

g is the acceleration of apparent gravity, pointing down (negative) or up (positive) along the vertical cable (m s−2),

gr is the gravitational acceleration due to Earth's pull, pointing down (negative)(m s−2),

a is the centrifugal acceleration, pointing up (positive) along the vertical cable (m s−2),

G is the gravitational constant (m3 s−2 kg−1)

M is the mass of the Earth (kg)

r is the distance from that point to Earth's center (m),

ω is Earth's rotation speed (radian/s).

At some point up the cable, the two terms (downward gravity and upward centrifugal force) are equal and opposite. Objects fixed to the cable at that point put no weight on the cable. This altitude (r1) depends on the mass of the planet and its rotation rate. Setting actual gravity equal to centrifugal acceleration gives:[54]: p. 126

r1=(GMω2)13

This is 35,786 km (22,236 mi) above Earth's surface, the altitude of geostationary orbit.[54]: Table 1

On the cable below geostationary orbit, downward gravity would be greater than the upward centrifugal force, so the apparent gravity would pull objects attached to the cable downward. Any object released from the cable below that level would initially accelerate downward along the cable. Then gradually it would deflect eastward from the cable. On the cable above the level of stationary orbit, upward centrifugal force would be greater than downward gravity, so the apparent gravity would pull objects attached to the cable upward. Any object released from the cable above the geosynchronous level would initially accelerate upward along the cable. Then gradually it would deflect westward from the cable.

### Cable section

Historically, the main technical problem has been considered the ability of the cable to hold up, with tension, the weight of itself below any given point. The greatest tension on a space elevator cable is at the point of geostationary orbit, 35,786 km (22,236 mi) above the Earth's equator. This means that the cable material, combined with its design, must be strong enough to hold up its own weight from the surface up to 35,786 km (22,236 mi). A cable which is thicker in cross section area at that height than at the surface could better hold up its own weight over a longer length. How the cross section area tapers from the maximum at 35,786 km (22,236 mi) to the minimum at the surface is therefore an important design factor for a space elevator cable.

Several taper profiles with different material parameters

To maximize the usable excess strength for a given amount of cable material, the cable's cross section area would need to be designed for the most part in such a way that the stress (i.e., the tension per unit of cross sectional area) is constant along the length of the cable.[54][55] The constant-stress criterion is a starting point in the design of the cable cross section area as it changes with altitude. Other factors considered in more detailed designs include thickening at altitudes where more space junk is present, consideration of the point stresses imposed by climbers, and the use of varied materials. To account for these and other factors, modern detailed designs seek to achieve the largest safety margin possible, with as little variation over altitude and time as possible.[22] In simple starting-point designs, that equates to constant-stress.

For a constant-stress cable with no safety margin, the cross-section-area as a function of distance from Earth's center is given by the following equation:[54]

A(r)=Asexp⁡[ρgR2T(1R+R22Rg3−1r−r22Rg3)]

where

g is the gravitational acceleration at Earth's surface (m·s−2),

As is the cross-section area of the cable at Earth's surface (m2),

ρ is the density of the material used for the cable (kg·m−3),

R is the Earth's equatorial radius,

Rg is the radius of geosynchronous orbit,

T is the stress the cross-section area can bear without yielding (N·m−2), its elastic limit.

Safety margin can be accounted for by dividing T by the desired safety factor.[54]

### Cable materials

Using the above formula, the ratio between the cross-section at geostationary orbit and the cross-section at Earth's surface, known as taper ratio, can be calculated:[note 1]

A(Rg)/As=exp⁡[ρT×4.85×107]

Taper ratio as a function of specific strength Taper ratio for some materials[54] Material | Tensile strength
(MPa) | Density
(kg/m3) | Specific strength
(MPa)/(kg/m3) | Taper ratio

|
|
|
|

Steel | 2,000 | 7,900 | 0.25 | 1.6×1033
Kevlar | 3,600 | 1,440 | 2.5 | 2.5×108
UHMWPE @23 °C | 3,600 | 0,980 | 3.7 | 5.4×106
Single wall carbon nanotube | 130,000 | 1,300 | 100 | 1.6

The taper ratio becomes very large unless the specific strength of the material used approaches 48 (MPa)/(kg/m3). Low specific strength materials require very large taper ratios which equates to large (or astronomical) total mass of the cable with associated large or impossible costs.

### Cable strength

Specific strength is of fundamental importance in the description of cable materials. The International Space Elevator Consortium has proposed a unit called the "Yuri", named after Yuri Artsutanov, to describe yield stress (or breaking stress) per unit of density of a material under tension. One Yuri equals 1 Pa⋅m3/kg or 1 N⋅m/kg, which is the breaking/yielding force per linear density of the cable under tension.[56][57] A functional Earth space elevator would require a tether of 30–80 megaYuri (corresponding to 3100–8200 km of breaking length).[58]

## Structure

One concept for the space elevator has it tethered to a mobile seagoing platform.

There are a variety of space elevator designs proposed for many planetary bodies. Almost every design includes a base station, a cable, climbers, and a counterweight. For an Earth Space Elevator the Earth's rotation creates upward centrifugal force on the counterweight. The counterweight is held down by the cable while the cable is held up and taut by the counterweight. The base station anchors the whole system to the surface of the Earth. Climbers climb up and down the cable with cargo.

### Base station

One concept for the base station/anchor would be a mobile station, such as large oceangoing vessels or other mobile platforms. Mobile base stations would have the advantage over the stationary concepts (with land-based anchors) by being able to maneuver to avoid high winds, storms, and space debris. Oceanic anchor points are also typically in international waters, simplifying and reducing the cost of negotiating territory use for the base station.[2]

Stationary land-based platforms would have simpler and less costly logistical access to the base. They also would have the advantage of being able to be at high altitudes, such as on top of mountains. In an alternate concept, the base station could be a tower, forming a space elevator which comprises both a compression tower close to the surface, and a tether structure at higher altitudes.[6] Combining a compression structure with a tension structure would reduce loads from the atmosphere at the Earth end of the tether, and reduce the distance into the Earth's gravity field that the cable needs to extend, and thus reduce the critical strength-to-density requirements for the cable material, all other design factors being equal.

### Cable

Carbon nanotubes are one of the candidates for a cable material.[35] A seagoing anchor station would also act as a deep-water seaport.

A space elevator cable would need to carry its own weight as well as the additional weight of climbers. The required strength of the cable would vary along its length. This is because at various points it would have to carry the weight of the cable below, or provide a downward force to retain the cable and counterweight above. Maximum tension on a space elevator cable would be at geosynchronous altitude so the cable would have to be thickest there and taper as it approaches Earth. Any potential cable design may be characterized by the taper factor – the ratio between the cable's radius at geosynchronous altitude and at the Earth's surface.[59]

The cable would need to be made of a material with a high tensile strength/density ratio. For example, the Edwards space elevator design assumes a cable material with a tensile strength of at least 100 gigapascals.[2] Since Edwards consistently assumed the density of his carbon nanotube cable to be 1300 kg/m3,[20] that implies a specific strength of 77 megapascal/(kg/m3). This value takes into consideration the entire weight of the space elevator. An untapered space elevator cable would need a material capable of sustaining a length of 4,960 kilometers (3,080 mi) of its own weight at sea level to reach a geostationary altitude of 35,786 km (22,236 mi) without yielding.[60] Therefore, a material with very high strength and lightness is needed.

For a space elevator on Earth, with its comparatively high gravity, the cable material would need to be stronger and lighter than currently available materials.[61] For this reason, there has been a focus on the development of new materials that meet the demanding specific strength requirement. For high specific strength, carbon has advantages because it is only the sixth element in the periodic table. Carbon has comparatively few of the protons and neutrons which contribute most of the dead weight of any material. Most of the interatomic bonding forces of any element are contributed by only the outer few electrons. For carbon, the strength and stability of those bonds is high compared to the mass of the atom. The challenge in using carbon nanotubes remains to extend to macroscopic sizes the production of such material that are still perfect on the microscopic scale (as microscopic defects are most responsible for material weakness).[61][62][63] As of 2014, carbon nanotube technology allowed growing tubes up to a few tenths of meters.[64]

In 2014, diamond nanothreads were first synthesized.[51] Since they have strength properties similar to carbon nanotubes, diamond nanothreads were quickly seen as candidate cable material as well.[52]

### Climbers

A conceptual drawing of a space elevator climber ascending through the clouds.

A space elevator cannot be an elevator in the typical sense (with moving cables) due to the need for the cable to be significantly wider at the center than at the tips. While various designs employing moving cables have been proposed, most cable designs call for the "elevator" to climb up a stationary cable.

Climbers cover a wide range of designs. On elevator designs whose cables are planar ribbons, most propose to use pairs of rollers to hold the cable with friction.

Climbers would need to be paced at optimal timings so as to minimize cable stress and oscillations and to maximize throughput. Lighter climbers could be sent up more often, with several going up at the same time. This would increase throughput somewhat, but would lower the mass of each individual payload.[65]

As the car climbs, the cable takes on a slight lean due to the Coriolis force. The top of the cable travels faster than the bottom. The climber is accelerated horizontally as it ascends by the Coriolis force which is imparted by angles of the cable. The lean-angle shown is exaggerated.

The horizontal speed, i.e. due to orbital rotation, of each part of the cable increases with altitude, proportional to distance from the center of the Earth, reaching low orbital speed at a point approximately 66 percent of the height between the surface and geostationary orbit, or a height of about 23,400 km. A payload released at this point would go into a highly eccentric elliptical orbit, staying just barely clear from atmospheric reentry, with the periapsis at the same altitude as low earth orbit (LEO) and the apoapsis at the release height. With increasing release height the orbit would become less eccentric as both periapsis and apoapsis increase, becoming circular at geostationary level.[66][67]

When the payload has reached GEO, the horizontal speed is exactly the speed of a circular orbit at that level, so that if released, it would remain adjacent to that point on the cable. The payload can also continue climbing further up the cable beyond GEO, allowing it to obtain higher speed at jettison. If released from 100,000 km, the payload would have enough speed to reach the asteroid belt.[12][22]

As a payload is lifted up a space elevator, it would gain not only altitude, but horizontal speed (angular momentum) as well. The angular momentum is taken from the Earth's rotation. As the climber ascends, it is initially moving slower than each successive part of cable it is moving on to. This is the Coriolis force: the climber "drags" (westward) on the cable, as it climbs, and slightly decreases the Earth's rotation speed. The opposite process would occur for descending payloads: the cable is tilted eastward, thus slightly increasing Earth's rotation speed.

The overall effect of the centrifugal force acting on the cable would cause it to constantly try to return to the energetically favorable vertical orientation, so after an object has been lifted on the cable, the counterweight would swing back toward the vertical, a bit like a pendulum.[65] Space elevators and their loads would be designed so that the center of mass is always well-enough above the level of geostationary orbit[68] to hold up the whole system. Lift and descent operations would need to be carefully planned so as to keep the pendulum-like motion of the counterweight around the tether point under control.[69]

Climber speed would be limited by the Coriolis force, available power, and by the need to ensure the climber's accelerating force does not break the cable. Climbers would also need to maintain a minimum average speed in order to move material up and down economically and expeditiously.[70] At the speed of a very fast car or train of 300 km/h (190 mph) it will take about 5 days to climb to geosynchronous orbit.[71]

### Powering climbers

Both power and energy are significant issues for climbers – the climbers would need to gain a large amount of potential energy as quickly as possible to clear the cable for the next payload.

Various methods have been proposed to provide energy to the climber:

* Transfer the energy to the climber through wireless energy transfer while it is climbing.
* Transfer the energy to the climber through some material structure while it is climbing.
* Store the energy in the climber before it starts – requires an extremely high specific energy such as nuclear energy.
* Solar power – After the first 40 km it is possible to use solar energy to power the climber[72]

Wireless energy transfer such as laser power beaming is currently considered the most likely method, using megawatt-powered free electron or solid state lasers in combination with adaptive mirrors approximately 10 m (33 ft) wide and a photovoltaic array on the climber tuned to the laser frequency for efficiency.[2] For climber designs powered by power beaming, this efficiency is an important design goal. Unused energy would need to be re-radiated away with heat-dissipation systems, which add to weight.

Yoshio Aoki, a professor of precision machinery engineering at Nihon University and director of the Japan Space Elevator Association, suggested including a second cable and using the conductivity of carbon nanotubes to provide power.[34]

### Counterweight

Space elevator with space station (NASA image)

Several solutions have been proposed to act as a counterweight:

* a heavy, captured asteroid[5][73]
* a space dock, space station or spaceport positioned past geostationary orbit
* a further upward extension of the cable itself so that the net upward pull would be the same as an equivalent counterweight
* parked spent climbers that had been used to thicken the cable during construction, other junk, and material lifted up the cable for the purpose of increasing the counterweight.[22]

Extending the cable has the advantage of some simplicity of the task and the fact that a payload that went to the end of the counterweight-cable would acquire considerable velocity relative to the Earth, allowing it to be launched into interplanetary space. Its disadvantage is the need to produce greater amounts of cable material as opposed to using just anything available that has mass.

## Applications

### Launching into deep space

As noted by Pearson,[12] a space elevator could also be used to toss a spacecraft further outward, using centrifugal force from the Earth's rotation. For example, an object attached to a space elevator at a radius of approximately 53,100 km would be at escape velocity when released. Transfer orbits to the L1 and L2 Lagrangian points could be attained by release at 50,630 and 51,240 km, respectively, and transfer to lunar orbit from 50,960 km.[74]

At the end of Pearson's 144,000 km (89,000 mi) cable, the tangential velocity is 10.93 kilometers per second (6.79 mi/s). That is more than enough to escape Earth's gravitational field and send probes at least as far out as Jupiter. Once at Jupiter, a gravitational assist maneuver could permit solar escape velocity to be reached.[12][54]

### Extraterrestrial elevators

A space elevator could also be constructed on other planets, asteroids and moons.

A Martian tether could be much shorter than one on Earth. Mars' surface gravity is 38 percent of Earth's, while it rotates around its axis in about the same time as Earth. Because of this, Martian stationary orbit is much closer to the surface, and hence the elevator could be much shorter. Current materials are already sufficiently strong to construct such an elevator.[75] Building a Martian elevator would be complicated by the Martian moon Phobos, which is in a low orbit and intersects the Equator regularly (twice every orbital period of 11 h 6 min). Phobos and Deimos may get in the way of an areostationary space elevator; on the other hand, they may contribute useful resources to the project. Phobos is projected to contain high amounts of carbon. If carbon nanotubes become feasible for a tether material, there will be an abundance of carbon near Mars. This could provide readily available resources for future colonization on Mars.

Space elevator Phobos Earth vs Mars vs Moon gravity at elevation

Phobos is tide-locked: one side always faces its primary, Mars. An elevator extending 6,000 km from that inward side would end about 28 kilometers above the Martian surface, just out of the denser parts of the atmosphere of Mars. A similar cable extending 6,000 km in the opposite direction would counterbalance the first, so the center of mass of this system remains in Phobos. In total the space elevator would extend out over 12,000 km which would be below areostationary orbit of Mars (17,032 km). A rocket launch would still be needed to get the rocket and cargo to the beginning of the space elevator 28 km above the surface. The surface of Mars is rotating at 0.25 km/s at the equator and the bottom of the space elevator would be rotating around Mars at 0.77 km/s, so only 0.52 km/s (1872 km/h) of Delta-v would be needed to get to the space elevator. Phobos orbits at 2.15 km/s and the outermost part of the space elevator would rotate around Mars at 3.52 km/s.[76][77]

The Earth's Moon is a potential location for a Lunar space elevator, especially as the specific strength required for the tether is low enough to use currently available materials. The Moon does not rotate fast enough for an elevator to be supported by centrifugal force (the proximity of the Earth means there is no effective lunar-stationary orbit), but differential gravity forces means that an elevator could be constructed through Lagrangian points.[16] A near-side elevator would extend through the Earth-Moon L1 point from an anchor point near the center of the visible part of Earth's Moon: the length of such an elevator must exceed the maximum L1 altitude of 59,548 km, and would be considerably longer to reduce the mass of the required apex counterweight.[78] A far-side lunar elevator would pass through the L2 Lagrangian point and would need to be longer than on the near-side; again, the tether length depends on the chosen apex anchor mass, but it could also be made of existing engineering materials.[78]

16 Psyche space elevator concept—the surface gravity is less than 2% of earths at ~0.144 m/s2[79] Ceres space elevator concept –
Surface gravity is

* 0.284 m/s2[80]
* 0.029 g

less than 3% of Earth's

Rapidly spinning asteroids or moons could use cables to eject materials to convenient points, such as Earth orbits;[81] or conversely, to eject materials to send a portion of the mass of the asteroid or moon to Earth orbit or a Lagrangian point. Freeman Dyson, a physicist and mathematician, suggested using such smaller systems as power generators at points distant from the Sun where solar power is uneconomical.

A space elevator using presently available engineering materials could be constructed between mutually tidally locked worlds, such as Pluto and Charon or the components of binary asteroid 90 Antiope, with no terminus disconnect, according to Francis Graham of Kent State University.[82] However, spooled variable lengths of cable must be used due to ellipticity of the orbits.

## Construction

Main article: Engineering:Space elevator construction

The construction of a space elevator would need reduction of some technical risk. Some advances in engineering, manufacturing and physical technology are required.[2] Once a first space elevator is built, the second one and all others would have the use of the previous ones to assist in construction, making their costs considerably lower. Such follow-on space elevators would also benefit from the great reduction in technical risk achieved by the construction of the first space elevator.[2]

Prior to the work of Edwards in 2000,[20] most concepts for constructing a space elevator had the cable manufactured in space. That was thought to be necessary for such a large and long object and for such a large counterweight. Manufacturing the cable in space would be done in principle by using an asteroid or Near-Earth object for source material.[19][83] These earlier concepts for construction require a large preexisting space-faring infrastructure to maneuver an asteroid into its needed orbit around Earth. They also required the development of technologies for manufacture in space of large quantities of exacting materials.[38]: 326

Since 2001, most work has focused on simpler methods of construction requiring much smaller space infrastructures. They conceive the launch of a long cable on a large spool, followed by deployment of it in space.[2][20][38]: 326 The spool would be initially parked in a geostationary orbit above the planned anchor point. A long cable would be dropped "downward" (toward Earth) and would be balanced by a mass being dropped "upward" (away from Earth) for the whole system to remain on the geosynchronous orbit. Earlier designs imagined the balancing mass to be another cable (with counterweight) extending upward, with the main spool remaining at the original geosynchronous orbit level. Most current designs elevate the spool itself as the main cable is payed out, a simpler process. When the lower end of the cable is long enough to reach the surface of the Earth (at the equator), it would be anchored. Once anchored, the center of mass would be elevated more (by adding mass at the upper end or by paying out more cable). This would add more tension to the whole cable, which could then be used as an elevator cable.

One plan for construction uses conventional rockets to place a "minimum size" initial seed cable of only 19,800 kg.[2] This first very small ribbon would be adequate to support the first 619 kg climber. The first 207 climbers would carry up and attach more cable to the original, increasing its cross section area and widening the initial ribbon to about 160 mm wide at its widest point. The result would be a 750-ton cable with a lift capacity of 20 tons per climber.

### Safety issues and construction challenges

Main article: Unsolved:Space elevator safety

For early systems, transit times from the surface to the level of geosynchronous orbit would be about five days. On these early systems, the time spent moving through the Van Allen radiation belts would be enough that passengers would need to be protected from radiation by shielding, which would add mass to the climber and decrease payload.[84]

A space elevator would present a navigational hazard, both to aircraft and spacecraft. Aircraft could be diverted by air-traffic control restrictions. All objects in stable orbits that have perigee below the maximum altitude of the cable that are not synchronous with the cable would impact the cable eventually, unless avoiding action is taken. One potential solution proposed by Edwards is to use a movable anchor (a sea anchor) to allow the tether to "dodge" any space debris large enough to track.[2]

### Economics

Main article: Finance:Space elevator economics

With a space elevator, materials might be sent into orbit at a fraction of the current cost. As of 2022, conventional rocket designs cost about US$12,125 per kilogram (US$5,500 per pound) for transfer to geostationary orbit.[85] Current space elevator proposals envision payload prices starting as low as $220 per kilogram ($100 per pound),[86] similar to the $5–$300/kg estimates of the Launch loop, but higher than the $310/ton to 500 km orbit quoted to Dr. Jerry Pournelle for an orbital airship system.[87]

Philip Ragan, co-author of the book Leaving the Planet by Space Elevator, states that "The first country to deploy a space elevator will have a 95 percent cost advantage and could potentially control all space activities."[88]

## International Space Elevator Consortium (ISEC)

The International Space Elevator Consortium (ISEC) is a US Non-Profit 501(c)(3) Corporation[89] formed to promote the development, construction, and operation of a space elevator as "a revolutionary and efficient way to space for all humanity".[90] It was formed after the Space Elevator Conference in Redmond, Washington in July 2008 and became an affiliate organization with the National Space Society[91] in August 2013.[90] ISEC hosts an annual Space Elevator conference at the Seattle Museum of Flight.[92][93][94]

ISEC coordinates with the two other major societies focusing on space elevators: the Japanese Space Elevator Association[95] and EuroSpaceward.[96] ISEC supports symposia and presentations at the International Academy of Astronautics[97] and the International Astronautical Federation Congress[98] each year.

## Related concepts

The conventional current concept of a "Space Elevator" has evolved from a static compressive structure reaching to the level of GEO, to the modern baseline idea of a static tensile structure anchored to the ground and extending to well above the level of GEO. In the current usage by practitioners (and in this article), a "Space Elevator" means the Tsiolkovsky-Artsutanov-Pearson type as considered by the International Space Elevator Consortium. This conventional type is a static structure fixed to the ground and extending into space high enough that cargo can climb the structure up from the ground to a level where simple release will put the cargo into an orbit.[99]

Some concepts related to this modern baseline are not usually termed a "Space Elevator", but are similar in some way and are sometimes termed "Space Elevator" by their proponents. For example, Hans Moravec published an article in 1977 called "A Non-Synchronous Orbital Skyhook" describing a concept using a rotating cable.[100] The rotation speed would exactly match the orbital speed in such a way that the tip velocity at the lowest point was zero compared to the object to be "elevated". It would dynamically grapple and then "elevate" high flying objects to orbit or low orbiting objects to higher orbit.

The original concept envisioned by Tsiolkovsky was a compression structure, a concept similar to an aerial mast. While such structures might reach space (100 km, 62 mi), they are unlikely to reach geostationary orbit. The concept of a Tsiolkovsky tower combined with a classic space elevator cable (reaching above the level of GEO) has been suggested.[6] Other ideas use very tall compressive towers to reduce the demands on launch vehicles.[101] The vehicle is "elevated" up the tower, which may extend as high as above the atmosphere, and is launched from the top. Such a tall tower to access near-space altitudes of 20 km (12 mi) has been proposed by various researchers.[101][102][103]

The aerovator is a concept invented by a Yahoo Group discussing space elevators, and included in a 2009 book about space elevators. It would consist of a >1000 km long ribbon extending diagonally upwards from a ground-level hub and then levelling out to become horizontal. Aircraft would pull on the ribbon while flying in a circle, causing the ribbon to rotate around the hub once every 13 minutes with its tip travelling at 8 km/s. The ribbon would stay in the air through a mix of aerodynamic lift and centrifugal force. Payloads would climb up the ribbon and then be launched from the fast-moving tip into orbit.[104]

Other concepts for non-rocket spacelaunch related to a space elevator (or parts of a space elevator) include an orbital ring, a space fountain, a launch loop, a skyhook, a space tether, and a buoyant "SpaceShaft".[105]

## Notes

1. ↑ Specific substitutions used to produce the factor 4.85×107:

A(Rg)/As=exp⁡[ρ×9.81×(6.378×106)2T(16.378×106+(6.378×106)22(4.2164×107)3−14.2164×107−(4.2164×107)22(4.2164×107)3)]

## See also

* Gravity elevator
* Orbital ring

## References

1. ↑ "What is a Space Elevator?". The International Space Elevator Consortium. 2014. https://www.isec.org/faq/#What is it.
2. ↑ 2.00 2.01 2.02 2.03 2.04 2.05 2.06 2.07 2.08 2.09 2.10 Edwards, Bradley Carl. ﻿The NIAC Space Elevator Program﻿ (Report). NASA Institute for Advanced Concepts. http://www.niac.usra.edu/studies/521Edwards.html. Retrieved 24 November 2007.
3. ↑ Tsiolkovsky, Konstantin (2004). Dreams of Earth and Sky. Athena Books. ISBN 9781414701639.
4. ↑ 4.0 4.1 Derek J. Pearson (2022). "The Steep Climb to Low Earth Orbit: A History of the Space Elevator Community's Battle Against the Rocket Paradigm.". https://vtechworks.lib.vt.edu/server/api/core/bitstreams/4e65652b-115e-4410-8aec-e17dbf33a8a9/content.
5. ↑ 5.0 5.1 "The Audacious Space Elevator". NASA Science News. https://science.nasa.gov/headlines/y2000/ast07sep_1.htm.
6. ↑ 6.0 6.1 6.2 Landis, Geoffrey A.; Cafarelli, Craig (1999). Presented as paper IAF-95-V.4.07, 46th International Astronautics Federation Congress, Oslo, Norway, 2–6 October 1995. "The Tsiolkovski Tower Reexamined". Journal of the British Interplanetary Society 52: 175–180. Bibcode: 1999JBIS...52..175L.
7. ↑ Artsutanov, Y. V Kosmos na Elektrovoze (Into Space by Funicular Railway). Komsomolskaya Pravda (Young Communist Pravda), 31 July 1960. Contents described in Lvov, Science 158:946, 17 November 1967
8. ↑ Lvov, Vladimir (1967-11-17). "Sky-Hook: Old Idea" (in en). Science 158 (3803): 946–947. doi:10.1126/science.158.3803.946. ISSN 0036-8075. PMID 17753605. Bibcode: 1967Sci...158..946L. https://www.science.org/doi/10.1126/science.158.3803.946.
9. ↑ Artsutanov, Yu (1960). "To the Cosmos by Electric Train". liftport.com. Young Person's Pravda. http://liftport.com/files/Artsutanov_Pravda_SE.pdf.
10. ↑ Bascom, Willard (2025-02-16). "John Dove Isaacs, March 28, 1913 - June 6, 1980". Biographies, Autobiographies, & Memoirs (University of California, San Diego). https://escholarship.org/content/qt1mn0v59d/qt1mn0v59d.pdf.
11. ↑ Isaacs, J. D.; Vine, A. C.; Bradner, H.; Bachus, G. E. (1966). "Satellite Elongation into a True 'Sky-Hook'". Science 151 (3711): 682–683. doi:10.1126/science.151.3711.682. PMID 17813792. Bibcode: 1966Sci...151..682I.
12. ↑ 12.0 12.1 12.2 12.3 12.4 Pearson, J. (1975). "The orbital tower: a spacecraft launcher using the Earth's rotational energy". Acta Astronautica 2 (9–10): 785–799. doi:10.1016/0094-5765(75)90021-1. Bibcode: 1975AcAau...2..785P. https://web.archive.org/web/20060521041805/http://www.star-tech-inc.com/papers/tower/tower.pdf. .
13. ↑ Clarke, Arthur C. (1979). The fountains of Paradise. Harcourt Brace Jovanovich. Harcourt Brace Jovanovich. ISBN 9780151327737.
14. ↑ Boucher, Marc (2013-04-08). "The Space Elevator: 'Thought Experiment', or Key to the Universe?" (in en-US). https://spaceref.com/newspace-and-tech/the-space-elevator-thought-experiment-or-key-to-the-universe-by-sir-arthur-c-clarke/.
15. ↑ Edwards, Bradley C. (2004). "A Space Elevator Based Exploration Strategy". AIP Conference Proceedings (AIP) 699: 854–862. doi:10.1063/1.1649650. Bibcode: 2004AIPC..699..854E. http://dx.doi.org/10.1063/1.1649650.
16. ↑ 16.0 16.1 Pearson, Jerome, “Anchored Lunar Satellites for Cislunar Transportation and Communication,” Journal of the Astronautical Sciences, Vol. XXVII, No. 1, pp. 39-62, Jan/Mar 1979. Retrieved 24 May 2026.
17. ↑ Pearson, Jerome, Levin, Eugene, Oldson, John, and Wykes, Harry (October, 2004). "The Lunar Space Elevator", 55th International Astronautical Congress, Vancouver, Canada. Retrieved 24 May 2026.
18. ↑ Science @ NASA, "Audacious & Outrageous: Space Elevators" , September 2000.
19. ↑ 19.0 19.1 19.2 Smitherman, Jr., D.V., ed (August 2000). ﻿Space Elevators: An Advanced Earth-Space Infrastructure for the New Millennium﻿ (Report). NASA. https://nss.org/wp-content/uploads/2000-Space-Elevator-NASA-CP210429.pdf.
20. ↑ 20.0 20.1 20.2 20.3 Edwards, Bradley C. (2000). "The Space Elevator", NASA Institute for Advanced Concepts. Retrieved 24 May 2026.
21. ↑ Edwards, Bradley C. (2003-03-01). ﻿The Space Elevator: NIAC Phase II Final Report﻿ (Report). Eureka Scientific. http://images.spaceref.com/docs/spaceelevator/521Edwards.pdf.
22. ↑ 22.0 22.1 22.2 22.3 Edwards, Bradley C. and Westling, Eric A. (2002) The Space Elevator: A Revolutionary Earth-to-Space Transportation System, San Francisco, California: Spageo Inc. ISBN 0-9726045-0-2.
23. ↑ Boyle, Alan (27 August 2004). "Space elevator contest proposed". NBC News. http://www.nbcnews.com/id/5792719.
24. ↑ "The Space Elevator – Elevator:2010". http://www.elevator2010.org/.
25. ↑ "Space Elevator Ribbon Climbing Robot Competition Rules". http://robogames.net/rules/climbing.php.
26. ↑ "NASA Announces First Centennial Challenges' Prizes". 2005. http://www.nasa.gov/home/hqnews/2005/mar/HQ_m05083_Centennial_prizes.html.
27. ↑ Britt, Robert Roy (24 March 2005). "NASA Details Cash Prizes for Space Privatization". Space.com. http://www.space.com/news/050323_centennial_challenge.html.
28. ↑ "What's the European Space Elevator Challenge?". European Space Elevator Challenge. http://eusec.warr.de/?eusec.
29. ↑ 29.0 29.1 Cain, Fraser (27 April 2005). "Space Elevator Group to Manufacture Nanotubes". Universe Today. http://www.universetoday.com/am/publish/liftport_manufacture_nanotubes.html?2742005.
30. ↑ Groshong, Kimm (15 February 2006). "Space-elevator tether climbs a mile high". New Scientist. http://www.newscientistspace.com/article/dn8725.html.
31. ↑ "If a space elevator was ever going to happen, it could have gotten its start in N. J. Here's how it went wrong". NJ.com. 28 March 2019. https://www.nj.com/cumberland/2019/04/if-a-space-elevator-was-ever-going-to-happen-it-could-have-gotten-its-start-in-nj-heres-how-it-went-wrong.html.
32. ↑ Elevator:2010 – The Space Elevator Challenge. spaceward.org.
33. ↑ Spaceward Games 2007. The Spaceward Foundation.
34. ↑ 34.0 34.1 Lewis, Leo (22 September 2008). "Japan hopes to turn sci-fi into reality with elevator to the stars". The Times (London, England). http://www.thetimes.co.uk/tto/news/world/article1967078.ece. Lewis, Leo; News International Group; accessed 22 September 2008.
35. ↑ 35.0 35.1 "Going up: Japan builder eyes space elevator". 22 February 2012. http://www.physorg.com/news/2012-02-japan-builder-eyes-space-elevator.html.
36. ↑ Daley, Jason (5 September 2018). "Japan Takes Tiny First Step Toward Space Elevator". Smithsonian Magazine. https://www.smithsonianmag.com/smart-news/researchers-take-tiny-first-step-toward-space-elevator-180970212/.
37. ↑ Ishikawa, Y. (2016). "Obayashi Corporation's Space Elevator Construction Concept". Journal of the British Interplanetary Society 69: 227–239. Bibcode: 2016JBIS...69..227I. https://ui.adsabs.harvard.edu/abs/2016JBIS...69..227I/abstract. Retrieved 5 January 2021.
38. ↑ 38.0 38.1 38.2 Space Elevators: An Assessment of the Technological Feasibility and the Way Forward. International Academy of Astronautics. 2013. ISBN 9782917761311. http://www.virginiaedition.com/media/spaceelevators.pdf.
39. ↑ ﻿Space Elevator Survivability, Space Debris Mitigation﻿ (Report). International Space Elevator Consortium. 2010. https://static1.squarespace.com/static/5e35af40fb280744e1b16f7b/t/5e5c1d06483fcf20335da699/1583095099789/2010StudyReport_SpaceElevatorSpaceDebris.pdf. [self-published source]
40. ↑ Gayomali, Chris (15 April 2014). "Google X Confirms The Rumors: It Really Did Try To Design A Space Elevator". Fast Company. http://www.fastcompany.com/3029138/world-changing-ideas/google-x-confirms-the-rumors-it-really-did-try-to-design-a-space-elevat?partner=rss.
41. ↑ Road to the Space Elevator Era. International Academy of Astronautics. 30 May 2019. ISBN 978-0-9913370-3-3. https://www.heinleinbooks.com/product-page/road-to-the-space-elevator-era.
42. ↑ 42.0 42.1 "Space Elevator Technology and Graphene: An Interview with Adrian Nixon". 23 July 2018. https://www.azom.com/article.aspx?ArticleID=16371.
43. ↑ "A space elevator is possible with today’s technology, researchers say (we just need to dangle it off the moon)". 12 September 2019. https://www.technologyreview.com/2019/09/12/102622/a-space-elevator-is-possible-with-todays-technology-researchers-say-we-just-need-to-dangle/.
44. ↑ Moravec, Hans (1978). Non-Synchronous Orbital Skyhooks for the Moon and Mars with Conventional Materials. Carnegie Mellon University. frc.ri.cmu.edu.
45. ↑ Fleming, Nic (15 February 2015). "Should We give up on the dream of space elevators?". BBC. http://www.bbc.com/future/story/20150211-space-elevators-a-lift-too-far. "'This is extremely complicated. I don't think it's really realistic to have a space elevator,' said Elon Musk during a conference at MIT, adding that it would be easier to 'have a bridge from LA to Tokyo' than an elevator that could take material into space."
46. ↑ Donahue, Michelle Z. (21 January 2016). "People Are Still Trying to Build a Space Elevator". Smithsonian Magazine. https://www.smithsonianmag.com/innovation/people-are-still-trying-build-space-elevator-180957877/. "'We understand it’s a difficult project,' Yoji Ishikawa says. 'Our technology is very low. If we need to be at 100 to get an elevator built – right now we are around a 1 or 2. But we cannot say this project is not possible.'"
47. ↑ "Why the world still awaits its first space elevator". The Economist. 30 January 2018. https://www.economist.com/the-economist-explains/2018/01/30/why-the-world-still-awaits-its-first-space-elevator. "The chief obstacle is that no known material has the necessary combination of lightness and strength needed for the cable, which has to be able to support its own weight. Carbon nanotubes are often touted as a possibility, but they have only about a tenth of the necessary strength-to-weight ratio and cannot be made into filaments more than a few centimetres long, let alone thousands of kilometres. Diamond nanothreads, another exotic form of carbon, might be stronger, but their properties are still poorly understood."
48. ↑ Aron, Jacob (13 June 2016). "Carbon nanotubes too weak to get a space elevator off the ground". New Scientist. https://www.newscientist.com/article/2093356-carbon-nanotubes-too-weak-to-get-a-space-elevator-off-the-ground/. "Feng Ding of the Hong Kong Polytechnic University and his colleagues simulated CNTs with a single atom out of place, turning two of the hexagons into a pentagon and heptagon, and creating a kink in the tube. They found this simple change was enough to cut the ideal strength of a CNT to 40 GPa, with the effect being even more severe when they increased the number of misaligned atoms... That’s bad news for people who want to build a space elevator, a cable between the Earth and an orbiting satellite that would provide easy access to space. Estimates suggest such a cable would need a tensile strength of 50 GPa, so CNTs were a promising solution, but Ding’s research suggests they won’t work."
49. ↑ Christensen, Billn (2 June 2006). "Nanotubes Might Not Have the Right Stuff". Space.com. https://www.space.com/2456-nanotubes-stuff.html. "recent calculations by Nicola Pugno of the Polytechnic of Turin, Italy, suggest that carbon nanotube cables will not work... According to their calculations, the cable would need to be twice as strong as that of any existing material including graphite, quartz, and diamond."
50. ↑ Whittaker, Clay (15 June 2016). "Carbon Nanotubes Can't Handle a Space Elevator". Popular Science. https://www.popsci.com/carbon-nanotubes-cant-handle-space-elevator/. "Alright, space elevator plans are back to square one, people. Carbon nanotubes probably aren't going to be our material solution for a space elevator, because apparently even a minuscule (read: atomic) flaw in the design drastically decreases strength."
51. ↑ 51.0 51.1 Calderone, Julia (26 September 2014). "Liquid Benzene Squeezed to Form Diamond Nanothreads". Scientific American. http://www.scientificamerican.com/article/liquid-benzene-squeezed-to-form-diamond-nanothreads/. Retrieved 22 July 2018.
52. ↑ 52.0 52.1 Anthony, Sebastian (23 September 2014). "New diamond nanothreads could be the key material for building a space elevator". Extremetech (Zeff Davis, LLC). http://www.extremetech.com/extreme/190691-new-diamond-nanothreads-could-be-the-key-material-for-building-a-space-elevator.
53. ↑ Raitt, David (March 2025). "The Contribution of Arthur C. Clarke to the Space Elevator." International Space Elevator Consortium" (in en-US). https://www.isec.org/history.
54. ↑ 54.0 54.1 54.2 54.3 54.4 54.5 54.6 54.7 Aravind, P. K. (2007). "The physics of the space elevator". American Journal of Physics 45 (2): 125. doi:10.1119/1.2404957. Bibcode: 2007AmJPh..75..125A. http://users.wpi.edu/~paravind/Publications/PKASpace Elevators.pdf. Retrieved 7 January 2013.
55. ↑ Artuković, Ranko (2000). "The Space Elevator". zadar.net
56. ↑ "Strong Tether Challenge 2013". http://www.isec.org/images/StrongTetherChallenge/2013/Handbook-ts2013.rev0.pdf.
57. ↑ "Terminology". isec.org. http://www.isec.org/sec/index.php/about-the-space-elevator/terminology#MegaYuri.
58. ↑ "Specific Strength in Yuris". keithcu.com. http://keithcu.com/wiki/index.php/Specific_Strength_in_Yuris.
59. ↑ Globus, Al. "NAS-97-029: NASA Applications of Molecular Nanotechnology". NASA. http://www.nas.nasa.gov/assets/pdf/techreports/1997/nas-97-029.pdf.
60. ↑ This 4,960 km "escape length" (calculated by Arthur C. Clarke in 1979) is much shorter than the actual distance spanned because centrifugal forces increase (and gravity decreases) dramatically with height: Clarke, A. C. (1979). "The space elevator: 'thought experiment', or key to the universe?". http://www.islandone.org/LEOBiblio/CLARK2.HTM.
61. ↑ 61.0 61.1 Scharr, Jillian (29 May 2013). "Space Elevators On Hold At Least Until Stronger Materials Are Available, Experts Say". Huffington Post. https://www.huffingtonpost.com/2013/05/29/space-elevators-stronger-materials_n_3353697.html.
62. ↑ Feltman, R. (7 March 2013). "Why Don't We Have Space Elevators?". Popular Mechanics. http://www.popularmechanics.com/science/space/nasa/why-dont-we-have-space-elevators-15185070.
63. ↑ Templeton, Graham (6 March 2014). "60,000 miles up: Space elevator could be built by 2035, says new study". Extreme Tech. http://www.extremetech.com/extreme/176625-60000-miles-up-geostationary-space-elevator-could-be-built-by-2035-says-new-study.
64. ↑ Wang, X.; Li, Q.; Xie, J.; Jin, Z.; Wang, J.; Li, Y.; Jiang, K.; Fan, S. (2009). "Fabrication of Ultralong and Electrically Uniform Single-Walled Carbon Nanotubes on Clean Substrates". Nano Letters 9 (9): 3137–3141. doi:10.1021/nl901260b. PMID 19650638. Bibcode: 2009NanoL...9.3137W. http://www.chem.pku.edu.cn/page/liy/labhomepage/publications/2009/2009NL.pdf.
65. ↑ 65.0 65.1 Lang, David D.. "Space Elevator Dynamic Response to In-Transit Climbers". http://spaceelevatorwiki.com/wiki/images/2/2b/Paper_Lang_Climber_Transit.pdf.
66. ↑ Gassend, Blaise. "Falling Climbers". http://gassend.net/spaceelevator/falling-climbers/index.html.
67. ↑ "Space elevator to low orbit?". 19 May 2010. http://www.endlessskyway.com/2010/05/space-elevator-to-low-orbit.html.
68. ↑ Gassend, Blaise. "Why the Space Elevator's Center of Mass is not at GEO". http://gassend.net/spaceelevator/center-of-mass/index.html.
69. ↑ Cohen, Stephen S.; Misra, Arun K. (2009). "The effect of climber transit on the space elevator dynamics". Acta Astronautica 64 (5–6): 538–553. doi:10.1016/j.actaastro.2008.10.003. Bibcode: 2009AcAau..64..538C.
70. ↑ Courtland, Rachel. "Space elevator trips could be agonisingly slow" (in en-US). https://www.newscientist.com/article/dn16223-space-elevator-trips-could-be-agonisingly-slow/.
71. ↑ Fawcett, Bill; Laine, Michael; Nugent Jr., Tom (2006) (in en). LIFTPORT. Canada: Meisha Merlin Publishing, Inc.. p. 103. ISBN 978-1-59222-109-7.
72. ↑ Swan, P. A.; Swan, C. W.; Penny, R. E.; Knapman, J. M.; Glaskowsky, P. N.. "Design Consideration for Space Elevator Tether Climbers". ISEC. http://isec.org/pdfs/isec_reports/2013_ISEC_Design_Considerations_for_Space_Elevator_Tether_Climbers_Final_Report.pdf. "During the last ten years, the assumption was that the only power available would come from the surface of the Earth, as it was inexpensive and technologically feasible. However, during the last ten years of discussions, conference papers, IAA Cosmic Studies, and interest around the globe, many discussions have led some individuals to the following conclusions: • Solar Array technology is improving rapidly and will enable sufficient energy for climbing • Tremendous advances are occurring in lightweight deployable structures."
73. ↑ Chodosh, Sara (29 March 2017). "This building hanging from an asteroid is absurd – but let's take it seriously for a second" (in en). Popular Science. https://www.popsci.com/building-hanging-from-an-asteroid/.
74. ↑ Engel, Kilian A.. "IAC-04-IAA.3.8.3.04 Lunar transportation scenarios utilising the space elevator". www.spaceelevator.com. http://www.spaceelevator.com/docs/iac-2004/iac-04-iaa.3.8.3.04.engel.pdf.
75. ↑ Forward, Robert L. and Moravec, Hans P. (22 March 1980) Space Elevators. Carnegie Mellon University. "Interestingly enough, they are already more than strong enough for constructing skyhooks on the moon and Mars."
76. ↑ Weinstein, Leonard M. (January 2003). "Space Colonization Using Space-Elevators from Phobos" (in en). AIP Conference Proceedings 654: 1227–1235. doi:10.1063/1.1541423. Bibcode: 2003AIPC..654.1227W. https://space.nss.org/wp-content/uploads/2003-Space-Colonization-Using-Space-Elevators-From-Phobos.pdf. Retrieved 23 December 2022.
77. ↑ Weinstein, Leonard (2003). "AIP Conference Proceedings". AIP Conference Proceedings. 654. pp. 1227–1235. doi:10.1063/1.1541423. Bibcode: 2003AIPC..654.1227W.
78. ↑ 78.0 78.1 Pearson, Jerome; Levin, Eugene; Oldson, John; Wykes, Harry (2005). "Lunar Space Elevators for Cislunar Space Development Phase I Final Technical Report". http://www.niac.usra.edu/files/studies/final_report/1032Pearson.pdf.
79. ↑ Shepard, Michael K. et al. (2017). "Radar observations and shape model of asteroid 16 Psyche". Icarus 281: 388–403. doi:10.1016/j.icarus.2016.08.011. Bibcode: 2017Icar..281..388S.
80. ↑ Calculated based on known parameters:
* Surface area: 4πr2
* Surface gravity: ⁠GM/r2⁠
* Escape velocity: √⁠2GM/r⁠
* Rotation velocity: ⁠rotation period/circumference⁠
81. ↑ Ben Shelef, the Spaceward Foundation. Asteroid Slingshot Express – Tether-based Sample Return .
82. ↑ Graham FG (2009). "Preliminary Design of a Cable Spacecraft Connecting Mutually Tidally Locked Planetary Bodies". 45th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit. doi:10.2514/6.2009-4906. ISBN 978-1-60086-972-3.
83. ↑ Hein, A. M., Producing a Space Elevator Tether Using a NEO: A Preliminary Assessment, International Astronautical Congress 2012, IAC-2012, Naples, Italy, 2012.
84. ↑ "Space elevators: 'First floor, deadly radiation!'". New Scientist. Reed Business Information Ltd.. 13 November 2006. https://www.newscientist.com/article/dn10520.
85. ↑ "Smallsat Rideshare Program". SpaceX. 1 March 2022. https://www.spacex.com/rideshare/#:~:text=$275k for 50kg to,LEO, GTO, and TLI..
86. ↑ The Spaceward Foundation. "The Space Elevator FAQ". Mountain View, California. http://www.spaceward.org/elevator-faq.
87. ↑ Pournelle, Jerry (23 April 2003). "Friday's VIEW post from the 2004 Space Access Conference". http://www.jerrypournelle.com/archives2/archives2view/view306.html#Friday.
88. ↑ Ramadge, Andrew; Schneider, Kate (17 November 2008). "Race on to build world's first space elevator". news.com.au. http://www.news.com.au/news/race-to-build-worlds-first-space-elevator/story-fna7dq6e-1111118059040.
89. ↑ "ISEC IRS filing". https://apps.irs.gov/app/eos/displayAll.do?dispatchMethod=displayAllInfo&Id=4984679&ein=800302896&country=US&deductibility=all&dispatchMethod=searchAll&isDescending=false&city=&ein1=80-0302896&postDateFrom=&exemptTypeCode=al&submitName=Search&sortColumn=orgName&totalResults=1&names=&resultsPerPage=25&indexOfFirstRow=0&postDateTo=&state=IL.
90. ↑ 90.0 90.1 "What is ISEC? : About Us". ISEC. http://www.isec.org/index.php/what-is-isec.
91. ↑ "NSS Affiliates". http://www.nss.org/about/affiliates.html.
92. ↑ David, Leonard (22 September 2014). "Space Elevator Advocates Take Lofty Look at Innovative Concepts" (in en). https://www.space.com/27225-space-elevator-technology.html.
93. ↑ "The International Space Elevator Consortium (ISEC) 2017 Space Elevator Conference" (in en-US). National Space Society. 14 August 2017. https://space.nss.org/the-international-space-elevator-consortium-isec-2017-space-elevator-conference/.
94. ↑ Boucher, Marc (17 July 2012). "Annual Space Elevator Conference Set for August 25–27". https://spaceref.com/newspace-and-tech/annual-space-elevator-conference-set-for-august-25-27/.
95. ↑ "Japan Space Elevator Association". http://www.jsea.jp/links/.
96. ↑ "Eurospaceward". 30 August 2015. http://www.eurospaceward.org/.
97. ↑ Akira, Tsuchida (2 October 2014). "Homepage of the Study Group 3.24, Road to Space Elevator Era". http://iaaweb.org/content/view/624/823/.
98. ↑ "IAC 2014 Meeting Schedule". http://www.iafastro.org/events/iac/iac-2014/meetings/.
99. ↑ "CLIMB: The Journal of the International Space Elevator Consortium", Volume 1, Number 1, December 2011, This journal is cited as an example of what is generally considered to be under the term "Space Elevator" by the international community. [1] .
100. ↑ Moravec, Hans P. (October–December 1977). "A Non-Synchronous Orbital Skyhook". Journal of the Astronautical Sciences 25: 307–322. Bibcode: 1977JAnSc..25..307M.
101. ↑ 101.0 101.1 Quine, B. M.; Seth, R. K.; Zhu, Z. H. (2009). "A free-standing space elevator structure: A practical alternative to the space tether". Acta Astronautica 65 (3–4): 365. doi:10.1016/j.actaastro.2009.02.018. Bibcode: 2009AcAau..65..365Q. http://pi.library.yorku.ca/dspace/bitstream/handle/10315/2587/AA_3369_Quine_Space_Elevator_Final_2009.pdf.
102. ↑ Landis, Geoffrey (1998). "Compression structures for Earth launch". 34th AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit. doi:10.2514/6.1998-3737.
103. ↑ Hjelmstad, Keith, "Structural Design of the Tall Tower", Hieroglyph, 30 November 2013. Retrieved 1 September 2015.
104. ↑ Van Pelt, Micheal (2009), "Space Elevators" (in en-us), Space Tethers and Space Elevators, New York, New York: Springer, pp. 143–178, doi:10.1007/978-0-387-76556-3_6, ISBN 978-0-387-76556-3, https://doi.org/10.1007/978-0-387-76556-3_6, retrieved 2023-12-27 .
105. ↑ "Space Shaft: Or, the story that would have been a bit finer, if only one had known...." (in en-US). https://ksj.mit.edu/tracker-archive/space-shaft-or-story-would-have-been-bit/.

## Further reading

* A conference publication based on findings from the Advanced Space Infrastructure Workshop on Geostationary Orbiting Tether "Space Elevator" Concepts (PDF), held in 1999 at the NASA Marshall Space Flight Center, Huntsville, Alabama. Compiled by D.V. Smitherman Jr., published August 2000
* "The Political Economy of Very Large Space Projects" HTML PDF, John Hickman, Ph.D. Journal of Evolution and Technology Vol. 4 – November 1999
* A Hoist to the Heavens By Bradley Carl Edwards
* Ziemelis K. (2001) "Going up". In New Scientist 2289: 24–27. Republished in SpaceRef . Title page: "The great space elevator: the dream machine that will turn us all into astronauts."
* The Space Elevator Comes Closer to Reality. An overview by Leonard David of space.com, published 27 March 2002
* Krishnaswamy, Sridhar. Stress Analysis – The Orbital Tower (PDF)
* LiftPort's Roadmap for Elevator To Space SE Roadmap (PDF)
* Shiga, David (28 March 2008). "Space elevators face wobble problem". New Scientist. https://www.newscientist.com/article/dn13552-space-elevators-face-wobble-problem/.
* Alexander Bolonkin, "Non Rocket Space Launch and Flight". Elsevier, 2005. 488 pgsISBN 978-0-08044-731-5.

## External links

* The Economist: Waiting For The Space Elevator (8 June 2006 – subscription required)
* CBC Radio Quirks and Quarks November 3, 2001 Riding the Space Elevator
* Times of London Online: Going up ... and the next floor is outer space
* The Space Elevator: 'Thought Experiment', or Key to the Universe? . By Sir Arthur C. Clarke. Address to the XXXth International Astronautical Congress, Munich, 20 September 1979
* International Space Elevator Consortium Website
* Space Elevator entry at The Encyclopedia of Science Fiction

* v
* t
* e

Space elevator

Main articles|

* History
* Structure
* Construction
* Economics
* Safety
* In fiction

Technologies|

* Electromagnetic propulsion
* Counterweight
* Carbon nanotube
* Nanotechnology
* Space tether
* Momentum exchange tether

Related concepts|

* Launch loop
* Lunar space elevator
* Orbital ring
* Skyhook
* Space fountain

Competitions|

* List of competitions
* Elevator

People|

* Yuri Artsutanov
* Bradley C. Edwards
* Jerome Pearson
* Konstantin Tsiolkovsky

Organizations|

* KC Space Pirates
* LaserMotive
* LiftPort Group

* Non-rocket spacelaunch
* Spaceflight
* Megascale engineering

* v
* t
* e

Non-rocket spacelaunch

Spaceflight

Static structures|

| Compressive|

* Space tower
* Pneumatic freestanding tower

|

Tensile|

| Orbiting skyhooks|

* Skyhook
* Momentum exchange tether

|

Space elevators|

Space elevator

Dynamic structures|

* Space fountain
* Orbital ring
* Launch loop
* Endo-atmospheric tether

Projectile launchers|

| Electrical|

* Coilgun
* Mass driver
* Railgun
* StarTram

|

Chemical|

* Space gun
* Blast wave accelerator
* Ram accelerator

Mechanical|

* Slingatron

Reaction drives|

* Air launch
* Spaceplanes
* Laser propulsion
* Beam-powered propulsion

Buoyant lifting|

* Balloon
* Buoyant space port
* High-altitude platform

See also
Rocket sled launch
Megascale engineering

* Category

* v
* t
* e

Emerging technologies

Fields|

| Agriculture|

* Agricultural robot
* Cellular agriculture
* Closed ecological systems
* Cultured meat
* Genetically modified food
* Precision agriculture
* Vertical farming

|

Architecture|

* Arcology
* Building printing
* Contour crafting
* Domed city

Biomedical|

* Artificial uterus
* Ampakine
* Brain transplant
* Cryonics
* Cryoprotectant
* Cryopreservation
* Vitrification
* Suspended animation
* De-extinction
* Genetic engineering
* Gene therapy
* Head transplant
* Isolated brain
* Life extension
* Strategies for Engineered Negligible Senescence
* Nanomedicine
* Nanosensors
* Organ printing
* Personalized medicine
* Regenerative medicine
* Stem-cell therapy
* Tissue engineering
* Robot-assisted surgery
* Synthetic biology
* Synthetic genomics
* Virotherapy
* Oncolytic virus
* Tricorder
* Whole genome sequencing

Displays|

| Next generation|

* FED
* FLCD
* iMoD
* Laser
* LPD
* OLED
* OLET
* QD-LED
* SED
* TPD
* TDEL
* TMOS
* MicroLED

|

Screenless|

* Bionic contact lens
* Head-mounted display
* Head-up display
* Optical head-mounted display
* Virtual retinal display

Other|

* Autostereoscopy
* Flexible display
* Holographic display
* Computer-generated holography
* Multi-primary color display
* Ultra HD
* Volumetric display

Electronics|

* Electronic nose
* E-textiles
* Flexible electronics
* Molecular electronics
* Nanoelectromechanical systems
* Memristor
* Spintronics
* Thermal copper pillar bump
* Twistronics

Energy|

| Production|

* Airborne wind turbine
* Artificial photosynthesis
* Biofuels
* Carbon-neutral fuel
* Concentrated solar power
* Fusion power
* Home fuel cell
* Hydrogen economy
* Methanol economy
* Molten salt reactor
* Nantenna
* Photovoltaic pavement
* Space-based solar power
* Vortex engine

|

Storage|

* Beltway battery
* Compressed air energy storage
* Flywheel energy storage
* Grid energy storage
* Lithium–air battery
* Molten-salt battery
* Nanowire battery
* Research in lithium-ion batteries
* Silicon–air battery
* Thermal energy storage
* Ultracapacitor

Other|

* Smart grid
* Wireless power

Information and
communications

* Ambient intelligence
* Internet of things
* Artificial intelligence
* Applications of artificial intelligence
* Progress in artificial intelligence
* Machine translation
* Mobile translation
* Machine vision
* Semantic Web
* Speech recognition
* Atomtronics
* Carbon nanotube field-effect transistor
* Cybermethodology
* Fourth-generation optical discs
* 3D optical data storage
* Holographic data storage
* GPGPU
* Memory
* CBRAM
* FRAM
* Millipede
* MRAM
* NRAM
* PRAM
* Racetrack memory
* RRAM
* SONOS
* Optical computing
* RFID
* Chipless RFID
* Software-defined radio
* Three-dimensional integrated circuit

Manufacturing|

* 3D printing
* Claytronics
* Molecular assembler
* Utility fog

Materials science|

* Aerogel
* Amorphous metal
* Artificial muscle
* Conductive polymer
* Femtotechnology
* Fullerene
* Graphene
* High-temperature superconductivity
* High-temperature superfluidity
* Linear acetylenic carbon
* Metamaterials
* Metamaterial cloaking
* Metal foam
* Multi-function structures
* Nanotechnology
* Carbon nanotubes
* Molecular nanotechnology
* Nanomaterials
* Picotechnology
* Programmable matter
* Quantum dots
* Silicene
* Superalloy
* Synthetic diamond

Military|

* Antimatter weapon
* Caseless ammunition
* Directed-energy weapon
* Laser
* Maser
* Particle-beam weapon
* Sonic weapon
* Coilgun
* Railgun
* Plasma weapon
* Pure fusion weapon
* Stealth technology
* Vortex ring gun

Neuroscience|

* Artificial brain
* Brain–computer interface
* Electroencephalography
* Mind uploading
* Brain-reading
* Neuroinformatics
* Neuroprosthetics
* Bionic eye
* Brain implant
* Exocortex
* Retinal implant

Quantum|

* Quantum algorithms
* Quantum amplifier
* Quantum bus
* Quantum channel
* Quantum circuit
* Quantum complexity theory
* Quantum computing
* Quantum cryptography
* Quantum dynamics
* Quantum electronics
* Quantum error correction
* Quantum imaging
* Quantum information
* Quantum key distribution
* Quantum logic
* Quantum logic gates
* Quantum machine
* Quantum machine learning
* Quantum metamaterial
* Quantum metrology
* Quantum network
* Quantum neural network
* Quantum optics
* Quantum programming
* Quantum sensing
* Quantum simulator
* Quantum teleportation

Robotics|

* Domotics
* Nanorobotics
* Powered exoskeleton
* Self-reconfiguring modular robot
* Swarm robotics
* Uncrewed vehicle

Space science|

| Launch|

* Fusion rocket
* Non-rocket spacelaunch
* Mass driver
* Orbital ring
* Skyhook
* Space elevator
* Space fountain
* Space tether
* Reusable launch system

|

Propulsion|

* Beam-powered propulsion
* Ion thruster
* Laser propulsion
* Plasma propulsion engine
* Helicon thruster
* VASIMR
* Nuclear pulse propulsion
* Solar sail

Other|

* Interstellar travel
* Propellant depot
* Laser communication in space

Transport|

| Aerial|

* Adaptive compliant wing
* Backpack helicopter
* Delivery drone
* Flying car
* High-altitude platform
* Jet pack
* Pulse detonation engine
* Scramjet
* Spaceplane
* Supersonic transport

|

Land|

* Airless tire
* Alternative fuel vehicle
* Hydrogen vehicle
* Driverless car
* Ground effect train
* Hyperloop
* Maglev train
* Personal rapid transit
* Transit Elevated Bus
* Vactrain
* Vehicular communication systems

Pipeline|

* Pneumatic transport
* Automated vacuum collection

Other|

* Anti-gravity
* Cloak of invisibility
* Digital scent technology
* Force field
* Plasma window
* Immersive virtual reality
* Magnetic refrigeration
* Phased-array optics

Topics|

* Collingridge dilemma
* Differential technological development
* Disruptive Innovation
* Ephemeralization
* Exploratory engineering
* Fictional technology
* Proactionary principle
* Technological change
* Technological unemployment
* Technological convergence
* Technological evolution
* Technological paradigm
* Technology forecasting
* Accelerating change
* Moore's law
* Technological singularity
* Technology scouting
* Technology readiness level
* Technology roadmap
* Transhumanism

* Category
* List

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Space elevator. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Astronomy:Space_elevator&oldid=4555625"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template