7.62×38mmR

Short description: Russian revolver cartridge

7.62×38mmR

Commercial production 7.62×38mmR (right) in comparison with .32 Smith & Wesson Long and .32 H&R Magnum

Type| Revolver
Place of origin| Belgium
Russian Empire
Service history
In service| 1895–present
Used by| Russian Empire
USSR
Russia
Wars| Russo-Japanese War
World War I
Russian Civil War
World War II
Post 1945 conflicts
Production history
Designer| Léon Nagant
Designed| 1895
Specifications
Case type| Rimmed
Bullet diameter| 7.82 (.308)
Neck diameter| 7.26 mm (0.286 in)
Shoulder diameter| 8.38 mm (0.330 in)
Base diameter| 8.94 mm (0.352 in)
Rim diameter| 9.855 mm (0.3880 in)
Case length| 38.86 mm (1.530 in)
Overall length| 38.86 mm (1.530 in)
Primer type| Berdan or boxer small pistol
Ballistic performance
| Bullet mass/type | Velocity | Energy

|
|

6.3 g (97 gr) FMC | 327 m/s (1,070 ft/s) | 340 J (250 ft⋅lbf)
7 g (108 gr) FMC Flat Nose | 306 m/s (1,000 ft/s) | 324 J (239 ft⋅lbf)
Test barrel length: 114 mm (4.5 in)
Source(s): [1][2][3]

7.62×38mmR (also known as 7.62 mm Nagant and Cartridge, Type R) is an ammunition cartridge designed for use in the Russian Nagant M1895 revolver.

A small number of experimental submachine guns (e.g., Tokarev 1927), designed by Fedor Tokarev, were also produced in a 7.62 mm Nagant chambering.[4] None, however, were accepted into Soviet service.[5][6]

## Contents

* 1 Background
* 2 Handloading
* 3 Producers
* 4 See also
* 5 References

## Background

The projectile is seated below the mouth of the cartridge, with the cartridge crimp sitting just above the bullet. When fired in the Nagant revolver, the crimp expands into the forcing cone, completing the gas seal and ostensibly increasing muzzle velocity by approximately 23 m/s (75 ft/s).

Commercially manufactured and loaded 7.62×38R cartridges are no longer difficult to find.

Most commercially loaded ammunition for the Nagant, including Fiocchi and the "СССР"-marked yellow box imports, are target ammunition, and do not have great stopping power. The low power of these rounds has given the Nagant a reputation as an underpowered sidearm. However, the original military ball cartridges fired bullets in the 6.5 g (100 grains) range at up to 330 m/s (1,100 ft/s), making them close to the .32-20 Winchester and .32 H&R Magnum in power. One advantage of the round, if proper brass can be found, is that it leaves the chambers totally clean, and there is no need to scrape lead and powder residue out.

Soviet 7,62 mm Nagant Revolver ctgs of 1930s with brass and copper-washed steel (right) cases.

## Handloading

7.62×38R (7.62 Nagant) cartridge (left) next to a .32 S&W Long Cartridge and a .22 LR cartridge for comparison.

7.62×38R Soviet military ammunition

Many users of this caliber handload their own ammunition. The proper brass cases are also expensive and difficult to come by. Handloaders have had success using dies for the .32-20 and .30 Carbine to handload the rounds. 32-20 brass cases are inexpensive, readily available, and can be reformed and used safely in guns chambered for 7.62×38R, but the resulting cartridges are too short to achieve the gas seal. Cut down 223 brass reformed in 30 carbine dies can be utilized to load for the Nagant also. These will achieve the gas seal, but the case rims will be undersized.[citation needed]

Three other cartridges—.32 S&W, .32 S&W Long, and .32 H&R Magnum—will also generally chamber and fire in the revolver, but will not achieve the gas seal. The case head of the .32 S&W/H&R is about the same size as the case diameter of the Nagant cartridge, so the case head will sometimes actually end up moving into the chamber, thus preventing an adequate primer strike. Due to the dimensional differences between these cartridges and the original 7.62×38R cartridge, this practice is done at the shooter's own risk. The .32 H&R Magnum in particular develops much higher pressures than the 7.62 Nagant or either of the .32 S&W cartridges, which are both late 19th century developments. The most common anomaly when firing these cartridges is bulged cases.[7]

## Producers

* Belgium
* Russian Empire
* Soviet Union[8]
* Second Polish Republic \- From 1929 until 1939[9]
* Italy - Fiocchi manufactures cartridges in this chambering; they fire 6.4 g (98 gr) FMJ bullets at about 260 m/s (850 ft/s), which works out to an energy of 213 J (157 ft·lbf)—comparable to a .32 ACP semi-automatic.
* Serbia - Prvi Partizan, a Serbian company produces a 7.62×38R load similar to Fiocchi's, originally under the "HotShot" brand but now under the standard Prvi Partizan label.[10]

## See also

* 7.62 mm caliber
* 7 mm caliber
* List of handgun cartridges
* Table of handgun and rifle cartridges

## References

1. ↑ Schreier, Philip (July 18, 2022). "The Model 1895 Nagant Revolver". https://www.shootingillustrated.com/content/the-model-1895-nagant-revolver/.
2. ↑ Campbell, Dave (August 9, 2020). "The 1895 Nagant Revolver: A Look Back". https://www.americanrifleman.org/content/the-1895-nagant-revolver-a-look-back/.
3. ↑ Herbert, Terril (June 6, 2017). "GUN REVIEW: RUSSIAN M1895 NAGANT REVOLVER IN 7.62X38R". https://www.guns.com/news/review/gun-review-the-russian-m1895-nagant-revolver-in-7-62x38r-video.
4. ↑ Williams, Anthony G. (2012). Sub-Machine Gun: The Development of Sub-Machine Guns and their Ammunition from World War 1 to the Present Day. The Crowood Press UK. p. 62. ISBN 978-1847972934.
5. ↑ Bolotin, David (1995). Soviet Small-Arms and Ammunition. Suomen Asemuseosaatio (Finnish Arms Museum Foundation, Finland). p. 44. ISBN 951-97184-1-9.
6. ↑ Ezell, Edward (1988). The AK-47 Story: Evolution of the Kalashnikov Weapons. Stackpole Books. ISBN 0-8117-2247-3.
7. ↑ "Nagant 1895". http://www.sff.net/people/sanders/nagant.html.
8. ↑ 7,62-мм револьверные патроны "Наган" // А. И. Благовестов. То, из чего стреляют в СНГ: Справочник стрелкового оружия. / под общ. ред. А. Е. Тараса. Минск, «Харвест», 2000. стр.524-525
9. ↑ Александр Борцов. Патроны Польши // журнал "Мастер-ружьё", № 9 (114) 2006. стр.70-73
10. ↑ BPrvi Partizan 7,62 mm Nagant

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/7.62×38mmR. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:7.62×38mmR&oldid=3243265"