Bus duct

Short description: Low resistance electrical conductor for high current transmission and distribution

Relevant topics on

Electrical installations
Wiring practice by region or country

* North American practice
* United Kingdom practice

Regulation of electrical installations

* BS 7671 UK wiring regulations
* IEC 60364 IEC international standard
* Canadian Electrical Code (CE Code)
* U.S. National Electrical Code (NEC)

Cabling and accessories

* AC power plugs and sockets
* Cable tray
* Electrical conduit
* Mineral-insulated copper-clad cable
* Multiway switching
* Steel wire armoured cable
* Ring main unit
* Ring circuit
* Thermoplastic-sheathed cable

Switching and protection devices

* AFCI
* ELCB
* Electrical busbar system
* Circuit breakers
* Disconnector
* Fuse
* Residual-current device
* Distribution board
* Consumer unit
* Electrical switch
* Earthing system

* v
* t
* e

5000 ampere copper and 4000 A aluminium bus ducts

In electric power distribution, a bus duct (also called busway) typically uses sheet metal, welded metal[1] or cast resin to contain and isolate copper or aluminium busbars for the purpose of conducting a substantial current of electricity. It is an alternative means of conducting electricity to power cables or cable bus.

Originally a busway consisted of bare copper conductors supported on inorganic insulators, such as porcelain, mounted within a non-ventilated steel housing.[2]

## Contents

* 1 History
* 2 Construction
* 3 See also
* 4 References
* 5 External links

## History

Busways were produced due to request of the automotive industry in Detroit in the late 1920s. Since that time, busways improved and became an integrated part of secondary network for industrial plants.[2]

## Construction

* Section of aluminium bus duct with sandwiched bus bars

* Innards of bus duct showing plastic wrappings of sandwiched busbars and hollow plastic tube spacers.

* Individual busbar wrapping

* Bus duct, also called busway, is available with (3) finger-safe #8AWG copper wires in steel housing.

Some bus ducts are rectangular similar to cable tray, but have thicker, cold-formed steel side rails and thinner sheet metal coverings. Others can be circular.[3] Busbars inside may be separated with distinct and even gaps between them, or “sandwiched” together.

Typically, individual busbars are wrapped or coated with a non-conducting, covalent material, such as plastic or (in older systems) electrical tape.

At the connection point, busbars flare out to enable connection to the next segment.

A plug-in bus duct system or busway can have disconnect switches and other devices mounted on it, for example, to distribute power along a long building. Many forms of busway allow plug-in devices such as switches and motor starters to be easily moved; this provides flexibility for changes on an assembly line, for example.[4] In addition to powering floor fixtures, busways can provide power to plug-in light fixtures and even IoT devices.[5]

Feeder busway is used to interconnect equipment, such as between a transformer and a switchgear line up. A variant type is a low-impedance busway, which is designed to have lower voltage drop by virtue of close spacing of bus bars, which reduces inductive reactance.

A trolley busway provides power to equipment that must be frequently moved. The busway is open at the bottom, and a movable collector assembly "trolley" is used to connect between the fixed bus bars in the busway and the cable connected to moving equipment.[4] Bus ducts are building service penetrants that are required to be externally firestopped where they penetrate fire separations required to have a fire-resistance rating.

## See also

* Bus (computing)
* Busbar
* Isolated-phase bus
* Duct (flow)

## References

1. ↑ "Isolated Phase Bus Duct" (in en-US). https://www.stacelectric.com/products/isolated-phase-bus-duct/.
2. ↑ 2.0 2.1 "IEEE 3001.5-2013 - IEEE Recommended Practice for the Application of Power Distribution Apparatus in Industrial and Commercial Power Systems". 2013-12-11. https://standards.ieee.org/findstds/standard/3001.5-2013.html.
3. ↑ "Isolated Phase Bus Duct" (in en-US). https://www.stacelectric.com/products/isolated-phase-bus-duct/.
4. ↑ 4.0 4.1 Terrel Croft, Wilford Summers (ed)American Electricians Handbook Eleventh Edition, McGraw-Hill 1987, ISBN 0-07013932-6, pages 9-114 through 9-132
5. ↑ "Why busSTRUT" (in en-US). https://busstrut.com/why-busstrut/.

## External links

* Merriam Webster Definition of Bus Duct
* YouTube Bus Duct Installation
* YouTube Bus Duct Construction and Installation
* Underwriters Laboratories Standard UL857 abstract
* IEEE C37.23 Standard For Metal Enclosed Bus
* Interpretations for IEEE Std C37.23-1987 IEEE Guide for Metal-Enclosed Bus and Calculating Losses in Isolated-Phase Bus
* IEEE P3004.7 - Recommended Practice for the Protection of Power Cables and Busway Used in Industrial and Commercial Power Systems
* IEEE Busway Short Circuit Testing Procedures
* IEEE Mathematical model of high voltage sandwich bus duct

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Bus duct. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:Bus_duct&oldid=4118935"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template