Design for X

Short description: Procedure and discipline in various fields

This article has an unclear citation style. The references used may be made clearer with a different or consistent style of citation and footnoting. (September 2009) (Learn how and when to remove this template message)

|

Design for excellence (DfX or DFX) is a term and abbreviation used interchangeably in the existing literature,[1][2][3] where the X in design for X is a variable which can have one of many possible values.[4] In many fields (e.g., very-large-scale integration (VLSI) and nanoelectronics) X may represent several traits or features including: manufacturability, power, variability, cost, yield, or reliability.[5] This gives rise to the terms design for manufacturability (DfM, DFM), design for inspection (DFI), design for variability (DfV), design for cost (DfC). Similarly, other disciplines may associate other traits, attributes, or objectives for X.

Under the label design for X, a wide set of specific design guidelines are summarized. Each design guideline addresses a given issue that is caused by, or affects the traits of, a product. The design guidelines usually propose an approach and corresponding methods that may help to generate and apply technical knowledge to control, improve, or even invent particular traits of a product. From a knowledge-based view, the design guideline represents an explicit form of procedural or knowing-how-to knowledge. However, two problems are prevalent. First, this explicit knowledge (i.e. the design guidelines) were transformed from a tacit form of knowledge (i.e., by experienced engineers, or other specialists). Thus, it is not granted that a freshman or someone who is outside the subject area will comprehend this generated explicit knowledge. This is because it still contains embedded fractions of knowledge or respectively include non-obvious assumptions, also called context-dependency. Second, the traits of a product are likely to exceed the knowledge base of one human. There exists a wide range of specialized fields of engineering, and considering the whole life cycle of a product will require non-engineering expertise. For this purpose, examples of design guidelines are listed in the following.

## Contents

* 1 Rules, guidelines, and methodologies along the product life cycle
* 1.1 Development phase
* 1.2 Production-operations phase
* 1.2.1 Design rules
* 1.2.2 Design guidelines
* 1.3 Use phase
* 1.3.1 Comparison: consumer durables vs. capital goods
* 1.4 Disposal phase
* 2 Similar concepts in product development
* 3 References
* 4 External links

## Rules, guidelines, and methodologies along the product life cycle

DfX methodologies address different issues that may occur in one or more phase of a product life cycle:

* Development phase
* Production phase
* Use phase
* Disposal phase

Each phase is explained with two dichotomous categories of tangible products to show differences in prioritizing design issues in certain product life cycle phases:

* Consumer durables
* Capital goods

Non-durables that are consumed physically when used, e.g. chocolate or lubricants, are not discussed. There also exist a wide range of other classifications because products are either (a) goods, (b) service, or (c) both (see OECD and Eurostat, 2005:48). Thus, one can also refer to whole product, augmented product, or extended product. Also the business unit strategy of a firm are ignored, even though it significantly influences priority-setting in design.

### Development phase

* Design rules
* Basic rules of embodiment design: clarity, simplicity, safety (Pahl and Beitz, 1996: 205–236)
* Organizational process
* Design for short time to market (Bralla, 1996: 255–266)
* System design, testing & validation
* Design for reliability (Bralla, 1996: 165–181), Synonyms: reliability engineering (VDI4001-4010)
* Design for test
* Design for safety (Bralla, 1996: 195–210; VDI2244); Synonyms: safety engineering, safe-life design
* Design for quality (Bralla, 1996: 149–164; VDI2247), Synonyms: quality engineering
* Design against corrosion damage (Pahl and Beitz, 1996: 294–304)
* Design for minimum risk (Pahl and Beitz, 1996:373–380)

### Production-operations phase

* Design rules
* Design to cost (Pahl and Beitz, 1996: 467–494; VDI2234; VDI 2235), see Target costing, Value engineering
* Design to standards (Pahl and Beitz, 1996:349–356), see Interchangeable parts, product modularity, product architecture, product platform
* Design Guidelines
* Design for assembly (Bralla, 1996: 127–136), (Pahl and Beitz, 1996: 340–349)
* Design for inspection (Hitchens Carl (2014) Guide to Engineering Metrology)
* Design for manufacturability (Bralla, 1996: 137–148), (Pahl and Beitz, 1996: 317–340)
* Design for logistics, design for postponement (see Delayed differentiation)
* Specific situations
* Design for electronic assemblies (Bralla, 1996: 267–279)
* Design for low-quantity production (Bralla, 1996: 280–288)

#### Design rules

Design to cost and design to standards serves cost reduction in production operations, or respectively supply chain operations. Except for luxury goods or brands (e.g., Swarovski crystals, Haute couture fashion, etc.), most goods, even exclusive products, rely on cost reduction, if these are mass produced. The same is valid for the functional production strategy of mass customization. Through engineering design physical interfaces between a) parts or components or assemblies of the product and b) the manufacturing equipment and the logistical material flow systems can be changed, and thus cost reducing effects in operating the latter may be achieved.

#### Design guidelines

* Design for manufacturability ensures the fabrication of single parts or components that are based on an integral design in mechanical engineering terms. Every production technology has its own specific design guideline that needs to be consulted depending on the situation.
* Design for assembly addresses the combination of single parts or components to subassemblies, assemblies, modules, systems, etc., that are based on a differential design in mechanical engineering terms. An important issue is how the embodied interfaces within a product are designed (mechanical engineering, electrical engineering). Contrary, software or respectively firmware interfaces (software engineering, electrical engineering) are not significant for assembly operations, because these can be easily flash installed within one production step. That is a cost efficient way to enable a wide range of product variants.
* Design for logistics covers issues along supply chain partners (i.e., legally independent firms) but is by its means closely related to the design for assembly guidelines. In academic research, design for logistics is tangent to the strategic alliances, supply chain management, and the engineering part of new product development. For example, Sanchez and Mahoney (1996) argued that product modularity (i.e., how physical sub-systems of a product are sub-divided through interfaces; also called product or system architecture), and organizational modularity (i.e., how organisational entities are structured), depend on each other. Fixson et al. (2005) found that the relationship between product architecture and organisational structure is reciprocal in the contexts of early supplier involvement during system design and the concept phase of the product development process.[6]

### Use phase

* User focused, see Product design, Industrial design
* Design for user-friendliness (Bralla, 1996: 237–254), see Usability, Ben Shneiderman, Emotional Design
* Design for ergonomics (Pahl and Beitz, 1996: 305–310)
* Design for aesthetics (Pahl and Beitz, 1996: 311–316)
* After-sales focused
* Design for serviceability (Bralla, 1996: 182–194; Pahl and Beitz, 1996: 357–359),
* Design for maintainability (Bralla, 1996: 182–194; Pahl and Beitz, 1996: 357–359; VDI2246),
* Design for repair-reuse-recyclability, a key part of the International Design Excellence Awards criteria

#### Comparison: consumer durables vs. capital goods

User focused design guidelines may be associated with consumer durables, and after-sales focused design guidelines may be more important for capital goods. However, in case of capital goods design for ergonomics is needed to ensure clarity, simplicity, and safety between the human-machine interface. The intent is to avoid shop-accidents as well as to ensure efficient work flows. Also design for aesthetics has become more and more important for capital goods in recent years. In business-to-business (B2B) markets, capital goods are usually ordered, or respectively business transaction are initiated, at industrial trade fairs. The functional traits of capital goods in technical terms are assumed generally as fulfilled across all exhibiting competitors. Therefore, a purchaser may be subliminally influenced by the aesthetics of a capital good when it comes to a purchasing decision. For consumer durables the aspect of after sales highly depends on the business unit's strategy in terms of service offerings, therefore generally statements are not possible to formulate.

### Disposal phase

* Design for Environment (Bralla, 1996: 182–194), see also Life cycle assessment, Technology assessment, sustainable engineering, sustainable design
* Design for recycling (Pahl and Beitz, 1996: 360–372), design for disassembly
* Active disassembly
* Remanufacturing
* Recycling of electrical and electronical equipment – Disassembly and processing (VDI2343)
* Recycling oriented product development (VDI 2243)

## Similar concepts in product development

Several other concepts in product development and new product development are very closely related:

* Engineering Design: Design for X
* Time dimension: product life cycle, Product Life Cycle Engineering, product life cycle management (that is not the same like the product cycle in business studies and economics, see e.g. Vernon (1966)). Primarily, the unit of analysis here is a product, or more clearly, one item
* Meso-level organisation: concurrent engineering (American), simultaneous engineering (British), and overlapping-parallel product development processes
* Micro-level organisation: cross-functional teams, inter-disciplinary teams, etc.

Looking at all life stages of a product (product life cycle (engineering)) is essential for design for X, otherwise the X may be suboptimized, or make no sense. When asking what competencies are required for analysing situations that may occur along the life of a product, it becomes clear that several departmental functions are required. An historical assumption is that new product development is conducted in a departmental-stage process (that can be traced back to the classical theory of the firm, e.g. Max Weber's bureaucracy or Henri Fayol's administration principles), i.e., new product development activities are closely associated with certain department of a firm. At the start of the 1990s, the concept of concurrent engineering gained popularity to overcome dysfunctions of departmental stage processes. Concurrent engineering postulates that several departments must work closely together for certain new product development activities (see Clark and Fujimoto, 1991). The logical consequence was the emergence of the organisational mechanism of cross-functional teams. For example, Filippini et al. (2005) found evidence that overlapping product development processes only accelerate new product development projects if these are executed by a cross-functional team, vice versa.

## References

1. ↑ Andrew B. Kahng, DfX and Signoff: The Coming Challenges and Opportunities, Keynote Address, IEEE Computer Society Annual Symposium on VLSI (ISVLSI), 2012.
2. ↑ Saraju Mohanty, DFX for Nanoelectronic Embedded Systems, Keynote Address at First IEEE Sponsored International Conference on Control, Automation, Robotics and Embedded System, CARE-2013, http://care.iiitdmj.ac.in/Keynote_Speakers.html
3. ↑ The DfX concept, http://www.ami.ac.uk/courses/topics/0248_dfx/
4. ↑ "DFA Transforms Computer Chassis". http://www.assemblymag.com/articles/84261-dfa-transforms-computer-chassis.
5. ↑ Saraju Mohanty, Chapter 3 Nanoelectronics Issues in Design for excellence, "Nanoelectronic Mixed-Signal System Design", ISBN 978-0071825719 and 0071825711, 1st Edition, McGraw-Hill, 2015.
6. ↑ Fixson, S. K., Ro, Y., & Liker, J. K. (2005). "Modularization and Outsourcing: Who drives whom? - A Study of Generational Sequences in the U.S. Automotive Cockpit Industry", International Journal of Automotive Technology and Management, 5(2): 166–183

Design for X references

* Pahl, G., and Beitz, W. (1996). Engineering Design - A Systematic Approach, 2nd edition, London: Springer. (Google Books Preview)
* Bralla, J. G. (1996). Design for Excellence. New York: McGraw-Hill.
* VDI-guidelines of the "Verein Deutscher Ingenieure" can requested under (www) or purchased from the publisher Beuth (www); most guidelines are bilingual in German and English.

Auxiliary references

* Doz, Y. and Santos, J.F.P. (1997). On the management of knowledge: from the transparency of collocation and co-setting to the quandary of dispersion and differentiation. Fontainebleau, France.
* Sanchez, R. and Mahoney, J.T. (1996) Modularity, flexibility, and knowledge management in product and organization design. Strategic Management Journal, 17, 63–76.
* OECD; Eurostat (2005). Oslo Manual 2005: The Measurement of Scientific and Technological Activities - Proposed guidelines for collecting and interpreting technological innovation data. Organisation for Economic Co-operation and Development, Statistical Office of the European Communities. (pdf)
* Vernon, R. (1966) International Investment and International Trade in the Product Cycle. The Quarterly Journal of Economics, 80, 190–207.
* Clark, K.B. and Fujimoto, T. (1991). Product development performance. Boston, Massachusetts: Harvard Business School Press.
* Filippini, R., Salmaso, L. and Tessarolo, P. (2005) Product Development Time Performance: Investigating the Effect of Interactions between Drivers. Journal of Product Innovation Management, 21, 199–214.

## External links

* DfX-Symposium in Germany
* The IBM Proprinter: A Case Study in Engineering Design
* Mottonen, M., Harkonen, J., Belt, P., Haapasalo, H. and Simila, J. (2009). "Managerial view on design for manufacturing", Industrial Management & Data Systems, Vol. 109, No. 6, pp. 859–872.
* [1]

* v
* t
* e

Design

* Outline
* Designer

Disciplines

| Communication
design|

* Advertising
* Book design
* Corporate design
* Exhibit design
* Film title design
* Graphic design
* Motion
* Postage stamp design
* Print design
* Illustration
* Information design
* Instructional design
* News design
* Photography
* Retail design
* Signage / Traffic sign design
* Typography / Type design
* Video design
* Visual merchandising

|

Environmental
design|

* Architecture
* Architectural lighting design
* Building design
* Passive solar
* Ecological design
* Environmental impact design
* Garden design
* Computer-aided
* Healthy community design
* Hotel design
* Interior architecture
* Interior design
* EID
* Keyline design
* Landscape architecture
* Sustainable
* Landscape design
* Spatial design
* Urban design

Industrial
design|

* Automotive design
* Automotive suspension design
* CMF design
* Corrugated box design
* Electric guitar design
* Furniture design
* Sustainable
* Hardware interface design
* Motorcycle design
* Packaging and labeling
* Photographic lens design
* Product design
* Production design
* Sensory design
* Service design

Interaction
design|

* Experience design
* EED
* Game design
* Level design
* Video game design
* Hardware interface design
* Icon design
* Immersive design
* Information design
* Sonic interaction design
* User experience design
* User interface design
* Web design

Other
applied arts|

* Public art design
* Ceramic / glass design
* Fashion design
* Costume design
* Jewelry design
* Floral design
* Game art design
* Property design
* Scenic design
* Sound design
* Stage/set lighting design
* Textile design

Other
design
& engineering|

* Algorithm design
* Behavioural design
* Boiler design
* Database design
* Drug design
* Electrical system design
* Experimental design
* Filter design
* Geometric design
* Job design
* Integrated circuit design
* Circuit design
* Physical design
* Power network design
* Mechanism design
* Nuclear weapon design
* Nucleic acid design
* Organization design
* Process design
* Processor design
* Protein design
* Research design
* Social design
* Software design
* Spacecraft design
* Strategic design
* Systems design

Approaches

* Activity-centered
* Adaptive web
* Affective
* Brainstorming
* By committee
* By contract
* C-K theory
* Closure
* Co-design
* Concept-oriented
* Configuration
* Contextual
* Continuous
* Cradle-to-cradle
* Creative problem-solving
* Creativity techniques
* Critical
* Design fiction
* Defensive
* Design–bid–build
* Design–build
* architect-led
* Domain-driven
* Ecodesign
* Energy neutral
* Engineering design process
* Probabilistic design
* Error-tolerant
* Fault-tolerant
* Framework-oriented
* For assembly
* For behaviour change
* For manufacturability
* For Six Sigma
* For testing
* For X
* Functional
* Generative
* Geodesign
* HCD
* High-level
* Inclusive
* Integrated
* Integrated topside
* Intelligence-based
* Iterative
* KISS principle
* Low-level
* Metadesign
* Mind mapping
* Modular
* New Wave
* Object-oriented
* Open
* Parametric
* Participatory
* Platform-based
* Policy-based
* Process-centered
* Public interest
* Rational
* Regenerative
* Reliability engineering
* Research-based
* Responsibility-driven
* RWD
* Safe-life
* Sustainable
* Systemic
* SOD
* Tableless web
* Theory of constraints
* Top-down and bottom-up
* Transformation
* Transgenerational
* TRIZ
* Universal
* Design for All
* Usage-centered
* Use-centered
* User-centered
* Empathic
* User innovation
* Value-driven
* Value sensitive
* Privacy by

* Design choice
* computing
* controls
* flow
* leadership
* management
* marker
* methods
* pattern
* research
* science
* sprint
* strategy
* theory
* thinking

* Tools
* Intellectual property
* Organizations
* Awards

| Tools|

* AAD
* Architectural model
* Blueprint
* Comprehensive layout
* CAD
* CAID
* Virtual home design software
* CAutoD
* Design quality indicator
* Electronic design automation
* Flowchart
* Mockup
* Product design specification
* Prototype
* Sketch
* Storyboard
* Technical drawing
* Web design program
* Website wireframe

|

Intellectual
property|

* Community design
* Design around
* Design patent
* Fashion design copyright
* Geschmacksmuster
* Industrial design rights
* European Union

Organizations|

* AIGA
* Chartered Society of Designers
* Design and Industries Association
* Design Council
* International Forum Design
* The Design Society
* Design Research Society

Awards|

* European Design Award
* German Design Award
* Good Design Award (Museum of Modern Art)
* Good Design Award (Chicago Athenaeum)
* Good Design Award (Japan)
* Graphex
* IF product design award
* James Dyson Award
* Prince Philip Designers Prize
* Prix Versailles

Related topics

* Aesthetics
* Agile
* Concept art
* Conceptual design
* Creative industries
* Cultural icon
* .design
* Enterprise architecture
* Futures studies
* Indie design
* Innovation Management
* Intelligent design
* Lean Startup
* New product development
* OODA Loop
* Philosophy of design
* Process simulation
* Slow design
* STEAM fields
* Unintelligent design
* Visualization
* Wicked problem

* Design brief
* change
* classic
* competition
* architectural
* student
* director
* education
* elements and principles
* engineer
* firm
* history
* knowledge
* language
* life
* load
* museum
* paradigm
* rationale
* review
* specification
* studio
* technology

* Commons
* Wikibooks
* Wikinews
* Wikiquote
* Wikisource
* Wiktionary

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Design for X. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:Design_for_X&oldid=4339117"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template