Jones Counter

Jones Counters: Upper- NYRRC model. Middle- Oerth model. Lower- Model JR

The Jones Counter is a type of bicycle odometer which adds the function of a surveyor's wheel to a bicycle. It was developed in 1971 by Alan Jones to accurately measure the length of road running race courses.[1] The counter has gears that drive a mechanical digital counter. One count typically corresponds to about 1/20 of a wheel revolution (this varies if a different gear ratio is used); this provides a resolution of about 10 cm in course length, although overall accuracy, depending on calibration and other factors, is lower, but normally better than 1 part in 1,000.

Almost all road running courses in the world are measured with this device. The Jones Counter has been used to measure all Olympic Marathon courses since the 1976 Montreal Olympics except for the 1980 Moscow Olympics. In addition, it has often been used to measure Olympic Road Race Walking Courses.

## Contents

* 1 Models
* 1.1 Clain Jones Counter
* 1.2 NYRRC Jones Counter
* 1.3 Jones-Oerth Counter
* 1.4 Jones-Oerth-Lacroix Counter
* 1.5 Jones Counter model JR
* 2 Use for measuring road-race courses
* 3 See also
* 4 References
* 5 External links

## Models

### Clain Jones Counter

Error creating thumbnail: Unable to save thumbnail to destinationOriginal Jones Counter, 1975

The original production version was manufactured by Alan Jones's son Clain from 1973 to 1982. The gearing produces 20 counts per revolution of the bicycle wheel.

### NYRRC Jones Counter

Production was taken over by New York Road Runners from 1983 to approximately 1990.

### Jones-Oerth Counter

Paul Oerth took up production in approximately 1990 and continued to about 2006. These models have a different gear ratio (260/11 counts per wheel revolution). In 2006, production of the necessary gears ceased, and an alternative plastic-encapsulated set of gears was introduced. This was short-lived, and the Oerth model went out of production.

### Jones-Oerth-Lacroix Counter

The JOL counter is a variation of the Jones-Oerth model. Created by Laurent Lacroix in 2000,[2][3] its distinguishing feature is a 27" rotary cable that allows the user to mount the Veeder-Root Counter on the handlebars.

### Jones Counter model JR

Development of a new model started in 2007.[4] The first production units became available in April 2008 and were used for the measurement of the London Marathon, which took place on April 13, 2008.

The gearing (260/11 counts per wheel revolution) is identical to that of the Jones-Oerth model.

## Use for measuring road-race courses

Error creating thumbnail: Jones Counter on the front wheel of a bicycle

To measure road-race courses, the counter is fitted to a bicycle between the left fork leg and the front wheel.[5] The tab or tabs on the large ring gear engage with the spokes, thus providing drive to a Veeder-Root counter.

Before the counter is used, the bicycle must first be calibrated by being ridden on a straight section of road between marks whose separation has been accurately measured by steel tape. A calibration can then be calculated in terms of counts per kilometer. Next, the bicycle is ridden over the race course to determine its length. Finally, the bicycle is recalibrated by riding again over the calibration distance. This is done to check for changes in bicycle-wheel diameter due to temperature changes, air leakage, and other causes.

## See also

* Short course prevention factor

## References

1. ↑ "The History of the Jones Counter". http://legacy.usatf.org/About/Committees/Long-Distance-Running/Road-Running-Technical-Council/Historical-Information/Jones-Counter.aspx.
2. ↑ Lacroix Counter
3. ↑ "Measurement News No 132 Summer 2006 page 32". http://www.usatf.org/events/courses/certification/measurement_news/MN132Summer06.pdf.
4. ↑ Course measurement forum. Designers' web site
5. ↑ Picture in course measurement lesson

## External links

* The Measurement of Road Race Courses (handbook of the IAAF)

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Jones Counter. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:Jones_Counter&oldid=2605703"