Xylan (coating)

Xylan is a fluoropolymer-based industrial coating, most commonly used in non-stick cookware. Generally, it is applied in a thin film to the target material to improve its durability and non-stick properties.

## Contents

* 1 Development
* 2 Applications
* 3 Properties
* 4 References

## Development

Consumer demand for non-stick coatings with improved durability drove research in the 1960s. DuPont, at that time focused on improving housewares, developed important properties of nonstick coatings through research. DuPont scientists found that adding Fluorinated ethylene propylene to the hard, adhesion-promoting binder resins produced one-coat products that were more durable than earlier Teflon formulations. In 1969, when Xylan was developed, Tefal and Teflon accounted for nearly all of the fluoropolymer coatings industry.[1]

## Applications

Xylan is generally used to reduce friction, improve wear resistance, and for non-stick applications. Additionally, it can be used to protect a metal from corrosion. The most commonly known application is in non-stick cookware but Xylan coatings have also been used extensively in the automotive industry and for corrosion protection in the oil and gas industry.[2]

Xylan is the umbrella trademark for most of the Whitford Corporation fluoropolymer coatings line. Xylan is made of low friction, wear resistant composites of fluoropolymers and reinforcing binder resins. Xylan coatings can be one-, two- (primer and top-coat), and three- (primer, mid-coat, top-coat) coat conventional and reinforced (filled) coating systems.

The fluoropolymers utilized in Xylan coatings consist of PTFE, PFA, and FEP. The properties listed below may not apply to all Xylan coatings as the fluoropolymer and resin content and type can have significant effects on each property.[3]

## Properties

Xylan coating properties[4] Parameter | Test Standard | CGS Vaue | SI Value

|
|
|

Tensile Strength | ASTM D1708 | 4000 – 5000 psi | 27.58–34.47 MPa
Elongation | ASTM D4894 | 50% | 50%
Impact Strength | ASTM D256 | 13 ft – lb/in |
Hardness | ASTM D2240 | 60 – 90 HB (shore D) |
Abrasion Resistance | TABER | > 15 mg | \-
Coefficient of Friction | ASTM D1894 | .15 – .35 static |
Dielectric Strength | ASTM D149 | 1400 volts/mil | 55118 kV/m
Use Temperature | - | −100 °F to 500 °F max | −73.3 °C to 260 °C
Melting Point | - | n/a | n/a
thermal conductivity | - | n/a | n/a
Chemical Resistance | ASTM D543 | Good | Good
Salt Spray Resistance | ASTM B117 | Excellent | Excellent
Water Absorption | ASTM D570 | < .03 % | < .03 %
Thickness | - | .0008" - .002" | 20.32 - 50.8 μm

## References

1. ↑ Ebnesajjad, Sina (11 May 2013). Introduction to Fluoropolymers: Materials, Technology and Applications. Elsevier Science. ISBN 9781455775514.
2. ↑ "PPG XYLAN® | PPG Industrial Coatings". https://www.ppgindustrialcoatings.com/en-US/products/ppg-xylan.
3. ↑ "Whitford Xylan® Coatings – Licensed Applicator Plas-Tech Coatings" (in en-US). https://www.plastechcoatings.com/whitford-coatings/xylan-coatings/.
4. ↑ "Xylan Coating". Metal Coatings Corporation. http://www.metcoat.com/xylan-coatings.htm.

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Xylan (coating). Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:Xylan_(coating)&oldid=972250"