Ethernet physical layer

Short description: Electrical or optical properties between network devices

Ethernet physical layer 220px

A standard 8P8C (often called RJ45) connector used most commonly on category 5 cable, one of the types of cabling used in Ethernet networks
Standard  | IEEE 802.3 (1983 onwards)
Physical media  | Twisted pair, optical fiber, coaxial cable
Network topology  | Point-to-point, star, bus
Major variants  | 10BASE5, 10BASE2, 10BASE-T, 100BASE-TX, 1000BASE-T, 10GBASE-R
Maximum distance  | 100 m (328 ft) over twisted pair, up to 100 km over optical fiber
Mode of operation  | optical, differential (balanced), single-ended
Maximum bit rate  | 1 Mbit/s to 800 Gbit/s
Voltage levels  | ± 2.5 V (over twisted pair)
Common connector types  | 8P8C, LC, SC, ST, MPO

The physical-layer specifications of the Ethernet family of computer network standards are published by the Institute of Electrical and Electronics Engineers (IEEE), which defines the electrical or optical properties and the transfer speed of the physical connection between a device and the network or between network devices. It is complemented by the MAC layer and the logical link layer. An implementation of a specific physical layer is commonly referred to as PHY.

The Ethernet physical layer has evolved over its existence starting in 1980 and encompasses multiple physical media interfaces and several orders of magnitude of speed from 1 Mbit/s to 800 Gbit/s. The physical medium ranges from bulky coaxial cable to twisted pair and optical fiber with a standardized reach of up to 80 km. In general, network protocol stack software will work similarly on all physical layers.

Many Ethernet adapters and switch ports support multiple speeds by using autonegotiation to set the speed and duplex for the best values supported by both connected devices. If autonegotiation fails, some multiple-speed devices sense the speed used by their partner,[1] but this may result in a duplex mismatch. With rare exceptions, a 100BASE-TX port (10/100) also supports 10BASE-T while a 1000BASE-T port (10/100/1000) also supports 10BASE-T and 100BASE-TX. Most 10GBASE-T ports also support 1000BASE-T,[2] some even 100BASE-TX or 10BASE-T. While autonegotiation can practically be relied on for Ethernet over twisted pair, few optical-fiber ports support multiple speeds. In any case, even multi-rate fiber interfaces only support a single wavelength (e.g. 850 nm for 1000BASE-SX or 10GBASE-SR).

10 Gigabit Ethernet was already used in both enterprise and carrier networks by 2007, with 40 Gbit/s[3][4] and 100 Gigabit Ethernet[5] ratified.[6] In 2024, the fastest additions to the Ethernet family were 800 Gbit/s variants.[7]

## Contents

* 1 Naming conventions
* 2 Physical layers
* 2.1 Early implementations and 10 Mbit/s
* 2.2 100 Mbit/s
* 2.3 1 Gbit/s
* 2.4 2.5 and 5 Gbit/s
* 2.5 10 Gbit/s
* 2.6 25 Gbit/s
* 2.7 40 Gbit/s
* 2.8 50 Gbit/s
* 2.9 100 Gbit/s
* 2.10 200 Gbit/s
* 2.11 400 Gbit/s
* 2.12 800 Gbit/s
* 2.13 1.6 Tbit/s
* 2.14 First mile
* 3 Sublayers
* 4 Twisted-pair cable
* 5 Minimum cable lengths
* 6 Related standards
* 7 References
* 8 External links

## Naming conventions

Generally, layers are named by their specifications:[8]

* 10, 100, 1000, 10G, ... – the nominal, usable speed at the top of the physical layer (no suffix = megabit/s, G = gigabit/s), excluding line codes but including other physical layer overhead (preamble, SFD, IPG); some WAN PHYs (W) run at slightly reduced bitrates for compatibility reasons; encoded PHY sublayers usually run at higher bitrates
* BASE, BROAD, PASS – indicates baseband, broadband, or passband signaling respectively
* -T, -T1, -S, -L, -E, -Z, -C, -K, -H ... – medium (PMD): T = twisted pair, -T1 = single-pair twisted pair, S = 850 nm short wavelength (multi-mode fiber), L = 1300 nm long wavelength (mostly single-mode fiber), E or Z = 1500 nm extra long wavelength (single-mode), B = bidirectional fiber (mostly single-mode) using WDM, P = passive optical (PON), C = copper/twinax, K = backplane, 2 or 5 or 36 = coax with 185/500/3600 m reach (obsolete), F = fiber, various wavelengths, H = plastic optical fiber
* X, R – PCS encoding method (varying with the generation): X for 8b/10b block encoding (4B5B for Fast Ethernet), R for large block encoding (64b/66b)
* 1, 2, 4, 10 – for LAN PHYs indicates number of lanes used per link; for WAN PHYs indicates reach in kilometers

For 10 Mbit/s, no encoding is indicated as all variants use Manchester code. Most twisted pair layers use unique encoding, so most often just -T is used.

The reach, especially for optical connections, is defined as the maximum achievable link length that is guaranteed to work when all channel parameters are met (modal bandwidth, attenuation, insertion losses etc.). With better channel parameters, often a longer, stable link length can be achieved. Vice versa, a link with worse channel parameters can also work but only over a shorter distance. Reach and maximum distance have the same meaning.

## Physical layers

The following sections provide a brief summary of official Ethernet media types. In addition to these official standards, many vendors have implemented proprietary media types for various reasons--often to support longer distances over fiber optic cabling.

### Early implementations and 10 Mbit/s

See also: Classic Ethernet

Early Ethernet standards used Manchester coding so that the signal was self-clocking and not adversely affected by high-pass filters.

Name  | Standard (Clause)  | Common connectors  | Link reach  | Required cable  | Description

|
|
|
|
|

Coaxial cable
Xerox experimental Ethernet  | Proprietary (1976)  | Vampire tap | 1 km  | 75 Ω coaxial
10BASE5 | 802.3-1985 (8)  | AUI, N, vampire tap | 500 m  | RG-8/U  | Original standard uses a single coaxial cable in which a connection is made by tapping into the single cable, drilling in to make contact with the core and the screen. Widespread deployment in the early 1980s. Was known also as DIX Standard (pre 802.3) and later as Thick-Ethernet (in contrast to 10BASE2, thinnet). 10 Mbit/s over expensive RG-8/U 50 Ω coaxial cabling, electrical bus topology with collision detection. Deprecated 2003.
10BASE2 | 802.3a-1985 (10)  | BNC, EAD/TAE-E | 185 m  | RG-58  | 50 Ω coaxial cable connects machines together, each machine using a T-connector to connect to its NIC. Requires terminators at each end. For many years during the mid to late 1980, this was the dominant Ethernet standard. Also called Thin Ethernet, Thinnet or Cheapernet. 10 Mbit/s over RG-58 coaxial cabling, bus topology with collision detection. Deprecated 2011.
10BROAD36 | 802.3b-1985 (11)  | F | 1800 m @VF0.87[9] | 75 Ω coaxial  | An early standard supporting Ethernet over longer distances. It utilized broadband modulation techniques, similar to those employed in cable modem systems, and operated over coaxial cable. 10 Mbit/s, scrambled NRZ signaling modulated (PSK) over high-frequency carrier, broad bandwidth coaxial cabling, bus topology with collision detection. Deprecated 2003.
Twisted-pair cable
1BASE5  | 802.3e-1987 (12)  | 8P8C (IEC 60603-7)  | 250 m  | voice-grade  | Also called StarLAN. Operated at 1 Mbit/s over twisted pair to an active hub, star topology. Although a commercial failure, 1BASE5 pioneered the use of twisted-pair cabling and defined the architecture for all subsequent Ethernet evolution on that medium. Deprecated 2003.
StarLAN 10  | Proprietary (1988)  | 8P8C  | 100 m  | voice-grade  | 10 Mbit/s over copper twisted pair cabling, star topology - evolved into 10BASE-T
LattisNet UTP  | Proprietary (1987)  | 8P8C  | 100 m  | voice-grade  | 10 Mbit/s over copper twisted pair cabling, star topology - evolved into 10BASE-T
10BASE-T | 802.3i-1990 (14)  | 8P8C (IEC 60603-7)  | 100 m  | Cat-3  | Runs over four wires (two twisted pairs). A repeater hub or switch sits in the middle and has a port for each node. This is also the configuration used for 100BASE-T. Copper twisted pair cabling, star topology - direct evolution of 1BASE-5. As of 2024[update], still widely supported.
10BASE-Te | 802.3az-2010 (14)  | 100 m  | Cat-5  | Energy-Efficient Ethernet variant of 10BASE-T using a reduced amplitude signal over Category 5 cable, completely interoperable with 10BASE-T nodes.
10BASE-T1L | 802.3cg-2019 (146)  | IEC 63171-1, IEC 63171-6  | 1000 m  |  | Ethernet over a single twisted pair - long reach, for industrial applications
10BASE-T1S | 802.3cg-2019 (147)  | 25 m  |  | Ethernet over a single twisted pair - short reach, for automotive applications with shared medium support, including PoDL
10BASE-T1M | 802.3da-2026

(188)

| 50 m  |  | Ethernet over a single twisted pair - medium reach, for automotive applications with shared medium support, including PoDL
Fiber-optical cable
FOIRL  | 802.3d-1987 (9.9)  | ST  | 1000 m  | FDDI-style MMF  | Fiber-optic inter-repeater link; the original standard for Ethernet over fiber, superseded by 10BASE-FL, deprecated 2011
10BASE-F | 802.3j-1993 (15)  |  |  |  | A generic term for the family of 10 Mbit/s Ethernet standards using fiber optic cable: 10BASE-FL, 10BASE-FB and 10BASE-FP. Of these only 10BASE-FL gained widespread use. 10 Mbit/s over fiber pair
10BASE-FL | 802.3j-1993 (15&18)  | ST  | 2000 m  | FDDI-style MMF  | An updated version of the FOIRL standard for end nodes, 2 km reach over FDDI-style multi-mode fiber, 850 nm wavelength
10BASE-FB | 802.3j-1993 (15&17)  | 2000 m  | Intended for backbones connecting a number of hubs or switches as a direct successor to FOIRL; deprecated 2011.[10]
10BASE‑FP | 802.3j-1993 (15&16)  | 1000 m  | A passive star network that required no repeater, it was never implemented.[10] Deprecated 2003.

### 100 Mbit/s

Main article: Fast Ethernet

All Fast Ethernet variants use a star topology and generally use 4B5B line coding.

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Twisted-pair cable
100BASE‑T | 802.3u-1995 (21) |  | A term for any of the three standards for 100 Mbit/s Ethernet over twisted pair cable. Includes 100BASE-TX, 100BASE-T4 and 100BASE-T2. As of 2009[update], 100BASE-TX has totally dominated the market, and may be considered synonymous with 100BASE-T in informal usage.
100BASE-TX | 802.3u-1995 (24, 25) | 8P8C (FDDI TP-PMD standard, ANSI INCITS 263-1995) | 4B5B MLT-3 coded signaling, Category 5 cable using two twisted pairs. The specifications are largely borrowed from FDDI's TP-PMD.[11] As of 2018[update], still very popular.
100BASE-T4 | 802.3u-1995 (23) | 8P8C (IEC 60603-7) | 8B6T PAM-3 coded signaling, Category 3 cable (as used for 10BASE-T installations) using four twisted pairs. Limited to half-duplex. Deprecated 2003.
100BASE-T2 | 802.3y-1998 (32) | 8P8C (IEC 60603-7) | PAM-5 coded signaling, CAT3 copper cabling with two twisted pairs, star topology. Supports full-duplex. It is functionally equivalent to 100BASE-TX, but supports old telephone cable. However, special sophisticated digital signal processors are required to handle the encoding schemes it uses, making this option fairly expensive at the time. It arrived well after 100BASE-TX was established in the market. 100BASE-T2 and 100BASE-T4 were not widely adopted but some of the technology developed for them is used in 1000BASE-T.[10] Deprecated 2003.
100BASE-T1 | 802.3bw-2015 (96) | none specified | Uses PAM-3 modulation at 66.7 MBd over a single, bi-directional twisted pair of up to 15 m; three bits are encoded as two ternary symbols. It is intended for automotive applications.
100BaseVG | 802.12-1994 | 8P8C | Standardized by a different IEEE 802 subgroup, 802.12, because it used a different, more centralized form of media access (demand priority). Proposed by Hewlett-Packard. Inherently half-duplex, it needed four pairs in a Cat-3 cable. Now obsolete, the standard has been withdrawn in 2001.
HDMI Ethernet Channel | HDMI 1.4 (2009) | HDMI | HEC uses a hybrid to mix and separate 100BASE-TX's transmit and receive signals through a single twisted pair.
Fiber-optical cable
100BASE‑FX | 802.3u-1995 (24, 26) | ST, SC | 4B5B NRZI coded signaling, two strands of multi-mode optical fiber using 1300 nm wavelength. Maximum length is 400 meters for half-duplex connections (to ensure collisions are detected) or 2 kilometers for full-duplex. The specifications are largely borrowed from FDDI.
100BASE‑SX | TIA-785 (2000) | ST, SC | 100 Mbit/s Ethernet over multi-mode fiber. Maximum length is 300 meters. 100BASE-SX used short wavelength (850 nm) optics that was sharable with 10BASE-FL, thus making an autonegotiation scheme possible with 10/100 fiber adapters.
100BASE‑BX10 | 802.3ah-2004 (58, 66) | ST, SC, LC | 100 Mbit/s Ethernet bidirectionally over a single strand of single-mode optical fiber. An optical multiplexer is used to split transmit and receive signals into different wavelengths (1530 and 1310 nm) allowing them to share the same fiber. Supports up to 10 km, full-duplex only.[12]
100BASE-LX10 | 802.3ah-2004 (58) | ST, SC, LC | 100 Mbit/s Ethernet up to 10 km over a pair of single-mode fibers, using 1310 wavelength, full-duplex only.[12]

### 1 Gbit/s

Main article: Gigabit Ethernet

All Gigabit Ethernet variants use a star topology. 1000BASE-X variants use 8b/10b PCS encoding. Initially, half-duplex mode was included in the standard but has since been abandoned.[13] Very few devices support gigabit speed in half-duplex.

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Twisted-pair cable
1000BASE-T  | 802.3ab-1999 (40)  | 8P8C (IEC 60603-7)  | PAM-5 coded signaling, at least Category 5 cable, with Category 5e strongly recommended copper cabling with four twisted pairs. Each pair is used in both directions simultaneously. Extremely wide adoption.
1000BASE-T1  | 802.3bp-2016 (97)  | none specified  | Uses a single, bi-directional twisted pair in full duplex mode only; cables specified for a reach of 15 m (automotive link segment) or 40 m (optional link segment), intended for automotive and industrial applications; it uses 80B/81B encoding in the PCS, PAM-3 signalling at 750 MBd (three bits transmitted as two ternary symbols) and includes Reed–Solomon error correction.
1000BASE-TX  | TIA-854 (2001)  | 8P8C (IEC 60603-7)  | Category 6 cable required. Unimplemented, withdrawn.
Fiber-optic cable
1000BASE-SX  | 802.3z-1998 (38)  | ST, SC, LC  | 8b/10b NRZ coded signaling on 850 nm carrier, short-range multi-mode fiber (up to 550 m).
1000BASE-LX  | 802.3z-1998 (38)  | SC, LC  | 8b/10b NRZ coded signaling on 1310 nm carrier, multi-mode fiber (up to 550 m) or single-mode fiber of up to 5 km; most current implementations are actually 1000BASE-LX10 with 10 km reach
1000BASE-BX10  | 802.3ah-2004 (59)  | SC, LC  | up to 10 km on 1490 and 1310 nm carriers; bidirectional over single strand of single-mode fiber; often called just 1000BASE-BX
1000BASE-LX10  | 802.3ah-2004 (59)  | SC, LC  | identical to 1000BASE-LX but increased power and sensitivity for up to 10 km over a pair of single-mode fiber; commonly called just 1000BASE-LX or, prior to 802.3ah, 1000BASE-LH; vendor-specific extensions exist for up to 40 km reach
1000BASE‑PX10‑D  | 802.3ah-2004 (60)  | SC, LC  | downstream (from head-end to tail-ends) over single-mode fiber using point-to-multipoint topology (supports at least 10 km).
1000BASE‑PX10‑U  | 802.3ah-2004 (60)  | upstream (from a tail-end to the head-end) over single-mode fiber using point-to-multipoint topology (supports at least 10 km).
1000BASE‑PX20‑D  | 802.3ah-2004 (60)  | downstream (from head-end to tail-ends) over single-mode fiber using point-to-multipoint topology (supports at least 20 km).
1000BASE‑PX20‑U  | 802.3ah-2004 (60)  | upstream (from a tail-end to the head-end) over single-mode fiber using point-to-multipoint topology (supports at least 20 km).
1000BASE-EX
1000BASE-ZX  | multi-vendor  | SC, LC  | up to 40 or 100 km over single-mode fiber on 1550 nm carrier[14]
Other
SFP | INF-8074i (2001) | SFP  | not a complete PHY in its own right but highly popular for adding modular transceivers; single lane, usually 1.25 Gbit/s
1000BASE-CX  | 802.3z-1998 (39)  | DE-9, FC style-2/IEC 61076-3-103, CX4/SFF-8470  | 8b/10b NRZ coded signaling over up to 25 m shielded, balanced copper cable (150 Ω). Predates 1000BASE-T and is rarely used.
1000BASE‑KX  | 802.3ap-2007 (70)  |  | 1 m over backplane
1000BASE-RHA
1000BASE-RHB
1000BASE-RHC  | 802.3bv-2017 (115)  | RHA: clamping fixture
RHB/RHC: none specified  | 1000BASE-RHA, -RHB, -RHC run over up to 50, 40, and 15 m of duplex plastic optical fiber (POF) using ~650 nm wavelength, 64b/65b encoding, and PAM16 symbols at 325 MBd; intended for home, industrial and automotive use, respectively

### 2.5 and 5 Gbit/s

Main article: 2.5GBASE-T and 5GBASE-T

2.5GBASE-T and 5GBASE-T are scaled-down variants of 10GBASE-T and provide longer reach over pre-Cat 6A cabling. These physical layers support twisted-pair copper cabling and backplanes only.

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Twisted-pair cable
2.5GBASE-T | 802.3bz-2016 (126) | 8P8C - IEC 60603-7-4 (unscreened) or IEC 60603-7-5 (screened) | 100 m of Cat 5e
5GBASE-T | 100 m of Cat 6
2.5GBASE-T1 | 802.3ch-2020 (149) |  | use a single, bi-directional twisted pair in full duplex mode only, intended for automotive and industrial applications
5GBASE-T1
Fiber-optical cable
2.5GBASE-AU | 802.3cz-2023 (166) | undefined | up to 40 m of OM3 for automotive
5GBASE-AU | up to 40 m of OM3 for automotive
Other
2.5GBASE-KX | 802.3cb-2018 (128) |  | 2.5 Gbit/s over 1 m of backplane, upscaled 1000BASE-KX
5GBASE-KR | 802.3cb-2018 (130) |  | 5 Gbit/s over 1 m of backplane, downscaled 10GBASE-KR

### 10 Gbit/s

Main article: 10 Gigabit Ethernet

10 Gigabit Ethernet is a version of Ethernet with a nominal data rate of 10 Gbit/s, ten times as fast as Gigabit Ethernet. The first 10 Gigabit Ethernet standard, IEEE Std 802.3ae-2002, was published in 2002. Subsequent standards encompass media types for single-mode fiber (long haul), multi-mode fiber (up to 400 m), copper backplane (up to 1 m) and copper twisted pair (up to 100 m). All 10-gigabit standards were consolidated into IEEE Std 802.3-2008. Most 10-gigabit variants use 64b/66b PCS code (-R). 10 Gigabit Ethernet, specifically 10GBASE-LR and 10GBASE-ER, enjoys significant market shares in carrier networks.

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Twisted-pair cable
10GBASE-T | 802.3an-2006 (55)  | 8P8C (IEC 60603-7-4 (unscreened) or IEC 60603-7-5 (screened))  | Uses Cat 6A twisted-pair wiring, four lanes at 800 MBd each, PAM-16 with DSQ128 line code
10GBASE-T1 | 802.3ch-2020 (149) |  | Uses a single, bi-directional twisted pair in full duplex mode only, intended for automotive and industrial applications
Fiber-optical cable
10GBASE-SR | 802.3ae-2002 (52)  | SC, LC  | Designed to support short distances over deployed multi-mode fiber cabling using 850 nm wavelength; it has a range of between 26 m and 400 m depending on cable type (modal bandwidth:reach: 160 MHz·km(FDDI):26 m, 200 MHz·km(OM1):33 m, 400 MHz·km:66 m, 500 MHz·km(OM2):82 m, 2000 MHz·km(>OM3):300 m, 4700 MHz·km(>OM4):400 m)[15]
10GBASE-LX4 | 802.3ae-2002 (53)  | SC, LC  | Uses four 8b/10b lanes with wavelength division multiplexing (1275, 1300, 1325, and 1350 nm) over deployed/legacy multi-mode cabling to support ranges of between 240 m and 300 m (400/500 MHz·km modal bandwidth). Also supports 10 km over single-mode fiber.
10GBASE-LR | 802.3ae-2002 (52)  | SC, LC  | Supports 10 km over single-mode fiber using 1,310 nm wavelength
10GBASE-ER | 802.3ae-2002 (52)  | SC, LC  | Supports 30 km over single-mode fiber using 1,550 nm wavelength (40 km over engineered links)
10GBASE-ZR | Multi-vendor  | SC, LC  | Offered by various vendors; supports 80 km or more over single-mode fiber using 1,550 nm wavelength
10GBASE-SW | 802.3ae-2002 (52)  |  | A variation of 10GBASE-SR with 9.58464 Gbit/s, designed to be mapped directly as OC-192/STM-64 SONET/SDH streams (850 nm wavelength)
10GBASE-LW | 802.3ae-2002 (52)  |  | A variation of 10GBASE-LR with 9.58464 Gbit/s, designed to be mapped directly as OC-192/STM-64 SONET/SDH streams (1,310 nm wavelength)
10GBASE-EW | 802.3ae-2002 (52)  |  | A variation of 10GBASE-ER with 9.58464 Gbit/s, designed to be mapped directly as OC-192/STM-64 SONET/SDH streams (1,550 nm wavelength)
10GBASE-LRM | 802.3aq-2006 (68)  | SC, LC  | Up to 220 m over deployed 500 MHz·km multi-mode fiber (1,310 nm wavelength)
10GBASE-PR | 802.3av-2009 (75)  |  | Providing P2MP 10 Gbit/s Ethernet links over PONs, at the distance of 10 or 20 km.
10GBASE-BR10
10GBASE-BR20
10GBASE-BR40  | 802.3cp-2021 (158)  | SC, LC  | bidirectional over a single strand of single-mode fiber for up to 10, 20 or 40 km using 1330 (-D; OLT→ONU) and 1270 nm (-U; ONU→OLT) wavelengths; pre-standard variants offered by various vendors, often called 10GBASE-BX or BiDi
10GBASE-AU | 802.3cz-2023 (166) | undefined | up to 40 m of OM3 for automotive
Other
10GBASE-CX4 | 802.3ak-2004 (54)  | CX4/SFF-8470/IEC 61076-3-113  | Designed to support short distances over copper cabling, it uses InfiniBand 4x connectors and CX4 twinaxial cabling and allows a cable length of up to 15 m. Was specified in IEEE 802.3ak-2004 which has been incorporated into IEEE 802.3-2008. Shipping has all but stopped in favor of 10GBASE-T and SFP+ direct attach.
10GBASE-KX4 | 802.3ap-2007 (71)  |  | 1 m over 4 lanes of backplane
10GBASE-KR | 802.3ap-2007 (72)  |  | 1 m over a single lane of backplane
10GPASS-XR | 802.3bn-2016 (100–102) |  | EPON Protocol over Coax (EPoC) – up to 10 Gbit/s downstream and 1.6 Gbit/s upstream for a passive optical, point-to-multipoint network using passband OFDM with up to 16384-QAM
SFP+ direct attach | SFF-8431 (2009)  | SFP+  | Up to 7 m using passive twinaxial cables, up to 15 m using active cables, or up to 100 m using active optical cables (AOC); single lane, usually 10.3125 Gbit/s

### 25 Gbit/s

Main article: 25 Gigabit Ethernet

Single-lane 25-gigabit Ethernet is based on one 25.78125 GBd lane of the four from the 100 Gigabit Ethernet standard developed by the P802.3by task force.[16] 25GBASE-T over twisted pair was approved alongside 40GBASE-T within IEEE 802.3bq.[17][18]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Twisted-pair cable
25GBASE-T  | 802.3bq-2016 (113)  | 8P8C (IEC 60603-7-51 and IEC 60603-7-81, 2000 MHz)  | Scaled-down version of 40GBASE-T – up to 30 m Category 8 or ISO/IEC TR 11801-9905 [B1] cabling
Fiber-optical cable
25GBASE-SR  | 802.3by-2016 (112)  | LC, SC  | 850 nm over multi-mode cabling with 100 m (OM4) or 70 m (OM3) reach
25GBASE-EPON
Nx25-EPON  | 802.3ca-2020 (141)  |  | Providing P2MP 25 Gbit/s Ethernet links over PONs, at a distance of at least 20 km.
25GBASE-LR  | 802.3cc-2017 (114)  | LC, SC  | 1310 nm over single-mode cabling with 10 km reach
25GBASE-ER  | 802.3cc-2017 (114)  | LC, SC  | 1300 nm over single-mode cabling with 30 km reach (40 km over engineered links)
25GBASE-BR10
25GBASE-BR20
25GBASE-BR40 | 802.3cp-2021 (159)  | SC, LC  | bidirectional over a single strand of single-mode fiber for up to 10, 20 or 40 km using 1330 (-D; OLT→ONU) and 1270 nm (-U; ONU→OLT) wavelengths for -BR10, or 1314/1290 nm wavelengths for -BR20 and -BR40
25GBASE-AU | 802.3cz-2023 (166) | undefined | up to 40 m of OM3 for automotive
Other
25GBASE-CR
25GBASE-CR-S  | 802.3by-2016 (110)  | SFP28 (SFF-8402/SFF-8432)  | Direct-attach cable (DAC) over twinaxial cabling with 3 m (-CR-S) and 5 m (-CR-L) reach
25GBASE-KR
25GBASE-KR-S  | 802.3by-2016 (111)  |  | For printed-circuit backplane, derived from 100GBASE-KR4
SFP28  | SFF-8402 (2014) | SFP28  | Popular for adding modular transceivers

### 40 Gbit/s

Main article: 100 Gigabit Ethernet

This class of Ethernet was standardized in June 2010 as IEEE 802.3ba. The work also included the first 100 Gbit/s generation, published in March 2011 as IEEE 802.3bg.[19][20] A 40 Gbit/s twisted-pair standard was published in 2016 as IEEE 802.3bq-2016.

Name[21] | Standard (Clause)  | Common connectors  | Description

|
|
|

Twisted-pair cable
40GBASE-T  | 802.3bq-2016 (113)  | 8P8C (IEC 60603-7-51 and IEC 60603-7-81, 2000 MHz)  | Requires Category 8 cabling, up to 30 m
Fiber-optical cable
40GBASE-SR4  | 802.3ba-2010 (86)  | MPO  | At least 100 m over 2000 MHz·km multi-mode fiber (OM3) at least 150 m over 4700 MHz·km multi-mode fiber (OM4)
40GBASE-LR4  | 802.3ba-2010 (87)  | SC, LC  | At least 10 km over single-mode fiber, CWDM with 4 lanes using 1270, 1290, 1310 and 1330 nm wavelength
40GBASE-ER4  | 802.3ba-2010 (87)  | SC, LC  | At least 30 km over single-mode fiber, CWDM with 4 lanes using 1270, 1290, 1310 and 1330 nm wavelength (40 km over engineered links)
40GBASE-FR  | 802.3bg-2011 (89)  | SC, LC  | Single lane, single-mode fiber over 2 km, 1550 nm wavelength
Other
40GBASE-KR4  | 802.3ba-2010 (84)  |  | At least 1 m over a backplane
40GBASE-CR4  | 802.3ba-2010 (85)  | QSFP+ (SFF-8436)  | Up to 7 m over twinaxial copper cable assembly (4 lanes, 10 Gbit/s each)

### 50 Gbit/s

The IEEE 802.3cd task force developed 50 Gbit/s along with next-generation 100 and 200 Gbit/s standards using 50 Gbit/s lanes.[22]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Fiber-optical cable
50GBASE-SR  | 802.3cd-2018 (138)  | LC, SC  | 100 m over OM4 multi-mode fiber using PAM-4 at 26.5625 GBd, 70 m over OM3
50GBASE-FR  | 802.3cd-2018 (139)  | LC, SC  | 2 km over single-mode fiber using PAM-4
50GBASE-LR  | 802.3cd-2018 (139)  | LC, SC  | 10 km over single-mode fiber using PAM-4
50GBASE-ER  | 802.3cd-2018 (139)  | LC, SC  | 30 km over single-mode fiber using PAM-4, 40 km over engineered links
50GBASE-BR10
50GBASE-BR20
50GBASE-BR40 | 802.3cp-2021 (160)  | SC, LC  | bidirectional over a single strand of single-mode fiber for up to 10, 20 or 40 km using 1330 (-D; OLT→ONU) and 1270 nm (-U; ONU→OLT) wavelengths for -BR10, or 1314/1290&nm wavelengths for -BR20 and -BR40
50GBASE-AU | 802.3cz-2023 (166) | undefined | up to 40 m of OM3 for automotive
Other
50GBASE-CR  | 802.3cd-2018 (136)  | SFP28, QSFP28, microQSFP, QSFP-DD, OSFP  | 3 m over twinaxial cable
50GBASE-KR  | 802.3cd-2018 (137)  |  | Printed-circuit backplane, consistent with 802.3bs Clause 124

### 100 Gbit/s

Main article: 100 Gigabit Ethernet

The first generation of 100 Gigabit Ethernet using 10 and 25 Gbit/s lanes was standardized in June 2010 as IEEE 802.3ba alongside 40 Gigabit Ethernet.[19] The second generation using 50 Gbit/s lanes was developed by the IEEE 802.3cd task force along with 50 and 200 Gbit/s standards.[22] The third generation using a single 100 Gbit/s lane was standardized in September 2022 as IEEE 802.3ck along with 200 and 400 Gbit/s Ethernet.[23][24]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Fiber-optical cable
100GBASE-SR10  | 802.3ba-2010 (86)  | MPO  | At least 100 m over 2000 MHz·km multi-mode fiber (OM3), at least 150 m over 4700 MHz·km multi-mode fiber (OM4)
100GBASE-SR4  | 802.3bm-2015 (95)  | MPO  | 4 lanes, at least 70 m over 2000 MHz·km multi-mode fiber (OM3), at least 100 m over 4700 MHz·km multi-mode fiber (OM4)
100GBASE-SR2  | 802.3cd-2018 (138)  | MPO  | Two 50 Gbit/s lanes using PAM-4 at 26.5625 GBd over OM4 multi-mode fiber with 100 m reach, 70 m over OM3, using RS-FEC(544,514) (Clause 91)
100GBASE-LR4  | 802.3ba-2010 (88)  | SC, LC  | At least 10 km over single-mode fiber, DWDM with 4 lanes using 1296, 1300, 1305 and 1310 nm wavelength
100GBASE-ER4  | 802.3ba-2010 (88)  | SC, LC  | At least 30 km over single-mode fiber, DWDM with 4 lanes using 1296, 1300, 1305 and 1310 nm wavelength (40 km over engineered links)
100GBASE-DR  | 802.3cu-2021 (140)  | LC, SC  | At least 500 m over single-mode fiber using a single lane, using RS-FEC and PAM4, 1310 nm wavelength
100GBASE-FR1  | At least 2 km over single-mode fiber using a single lane, using RS-FEC and PAM4, 1310 nm wavelength
100GBASE-LR1  | At least 10 km over single-mode fiber using a single lane, using RS-FEC and PAM4, 1310 nm wavelength
100GBASE-ZR  | 802.3ct-2021 (153 & 154)  | At least 80 km over single-mode fiber using a single wavelength over a DWDM system, also forming the base for 200GBASE-ZR and 400GBASE-ZR
Other
100GBASE-CR10  | 802.3ba-2010 (85)  | CXP10 (SFF-8642)  | Up to 7 m over twinaxial copper cable assembly (10 lanes, 10 Gbit/s each)
100GBASE-CR4  | 802.3bj-2014 (92)  | QSFP28 4X (SFF-8665)  | Up to 5 m over twinaxial copper cable assembly (4 lanes, 25 Gbit/s each)
100GBASE-CR2  | 802.3cd-2018 (136)  | QSFP28, microQSFP, QSFP-DD, OSFP  | Over twinaxial cable with 3 m reach (two 50 Gbit/s lanes), using RS-FEC
100GBASE-CR1  | 802.3ck-2022 (162)  |  | Single-lane over twin-axial copper with at least 2 m reach
100GBASE-KR4  | 802.3bj-2014 (93)  |  | Four lanes 25 Gbit/s each over a backplane
100GBASE-KR2  | 802.3cd-2018 (137)  |  | Two 50 Gbit/s lanes over printed-circuit backplane, consistent with 802.3bs Clause 124, using RS-FEC
100GBASE-KR1  | 802.3ck-2022 (163)  |  | Single-lane over electrical backplanes supporting an insertion loss of up to 28 dB at 26.5625 GBd
100GBASE-KP4  | 802.3bj-2014 (94)  |  | Using PAM4 modulation on four lanes 12.5 GBd each over a backplane, using RS-FEC

### 200 Gbit/s

First generation 200 Gbit/s have been defined by the IEEE 802.3bs task force and standardized in 802.3bs-2017.[25] The IEEE 802.3cd task force has developed 50 and next-generation 100 and 200 Gbit/s standards using one, two, or four 50 Gbit/s lanes respectively.[22] The next generation using 100 Gbit/s lanes was standardized in September 2022 as IEEE 802.3ck along with 100 and 400 Gbit/s PHYs and attachment unit interfaces (AUI) using 100 Gbit/s lanes.[23][24]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Fiber-optical cable
200GBASE-DR4  | 802.3bs-2017 (121) | MPO  | Four PAM-4 lanes (26.5625 GBd) using individual strands of single-mode fiber with 500 m reach (1310 nm)
200GBASE-FR4  | 802.3bs-2017 (122) | SC, LC  | Four PAM-4 lanes (26.5625 GBd) using four wavelengths (CWDM) over single-mode fiber with 2 km reach (1270/1290/1310/1330 nm)
200GBASE-LR4  | 802.3bs-2017 (122) | SC, LC  | Four PAM-4 lanes (26.5625 GBd) using four wavelengths (DWDM, 1296/1300/1305/1309 nm) over single-mode fiber with 10 km reach
200GBASE-SR4  | 802.3cd-2018 (138) | MPO  | Four PAM-4 lanes at 26.5625 GBd each over OM4 multi-mode fiber with 100 m reach, 70 m over OM3
200GBASE-ER4  | 802.3cn-2019 (122)  |  | Four-lane using four wavelengths (DWDM, 1296/1300/1305/1309 nm) over single-mode fiber with 30 km reach, 40 km over engineered links
TBD | 802.3df |  | single-pair single-mode fiber with 500 m reach
TBD |  | single-pair single-mode fiber with 2 km reach
Other
200GBASE-CR4  | 802.3cd-2018 (136) | QSFP28, microQSFP, QSFP-DD, OSFP  | Four PAM-4 lanes (26.5625 GBd) over twinaxial cable with 3 m reach
200GBASE-KR4  | 802.3cd-2018 (137) |  | Four PAM-4 lanes (26.5625 GBd) over printed-circuit backplane, consistent with 802.3bs Clause 124
200GBASE-CR2  | 802.3ck-2022 (162) |  | Two-lane over twin-axial copper with at least 2 m reach
200GBASE-KR2  | 802.3ck-2022 (163) |  | Two-lane over electrical backplanes supporting an insertion loss of up to 28 dB at 26.56 GBd
TBD | 802.3df |  | single-pair twinaxial cable with 1 m reach

### 400 Gbit/s

Main article: Terabit Ethernet

An Ethernet standard capable of 200 and 400 Gbit/s is defined in IEEE 802.3bs-2017.[25] 1 Tbit/s may be a further goal.[26]

In May 2018, IEEE 802.3 started the 802.3ck task force to develop standards for 100, 200, and 400 Gbit/s PHYs and attachment unit interfaces (AUI) using 100 Gbit/s lanes.[23] The new standards were approved in September 2022.[24]

In 2008, Robert Metcalfe, one of the co-inventors of Ethernet, said he believed commercial applications using Terabit Ethernet may occur by 2015, though it might require new Ethernet standards.[27] It was predicted this would be followed rapidly by a scaling to 100 Terabit, possibly as early as 2020. These were theoretical predictions of technological ability, rather than estimates of when such speeds would actually become available at a practical price point.[28]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Fiber-optical cable
400GBASE-SR16  | 802.3bs-2017 (123) | MPO-32  | Sixteen lanes (26.5625 Gbit/s) using individual strands of OM4/OM5 multi-mode fiber with 100 m reach or 70 m over OM3
400GBASE-DR4  | 802.3bs-2017 (124) | MPO  | Four PAM-4 lanes (53.125 GBd) using individual strands of single-mode fiber with 500 m reach (1310 nm)
400GBASE-FR8  | 802.3bs-2017 (122) | SC, LC  | Eight PAM-4 lanes (26.5625 GBd) using eight wavelengths (CWDM) over single-mode fiber with 2 km reach
400GBASE-LR8  | 802.3bs-2017 (122) | SC, LC  | Eight PAM-4 lanes (26.5625 GBd) using eight wavelengths (DWDM) over single-mode fiber with 10 km reach
400GBASE-FR4  | 802.3cu-2021 (151) | SC, LC  | Four lanes/wavelengths (CWDM, 1271/1291/1311/1331 nm) over single-mode fiber with 2 km reach, using PAM4
400GBASE-LR4-6  | Four lanes/wavelengths (CWDM, 1271/1291/1311/1331 nm) over single-mode fiber with 6 km reach, using PAM4
400GBASE-SR8  | 802.3cm-2020 (138) | MPO-24, MPO-16  | Eight-lane using individual strands of multi-mode fiber with 100 m reach
400GBASE-SR4.2  | 802.3cm-2020 (150) | MPO-12  | Eight-lane using four multi-mode fiber pairs and two wavelengths (850 and 910 nm) with 70/100/150 m reach over OM3/OM4/OM5 respectively
400GBASE-ER8  | 802.3cn-2019 (122) | SC, LC  | Eight-lane using eight wavelengths over single-mode fiber with 40 km reach
400GBASE-ZR  | 802.3cw (155 & 156)  | SC, LC  | At least 80 km over single-mode fiber using a single wavelength with 16QAM over a DWDM system
TBD | 802.3df |  | two pairs of single-mode fiber with 500 m reach
Other
400GBASE-CR4  | 802.3ck-2022 (162) |  | Four-lane over twin-axial copper with at least 2 m reach
400GBASE-KR4  | 802.3ck-2022 (163) |  | Four-lane over electrical backplanes supporting an insertion loss of up to 28 dB at 26.56 GBd
TBD | 802.3df |  | two pairs of twin-axial copper with 1 m reach

### 800 Gbit/s

The Ethernet Technology Consortium proposed an 800 Gbit/s Ethernet PCS variant based on tightly bundled 400GBASE-R in April 2020.[29]

In February 2024, the IEEE 802.3df Task Force defined variants for 800 Gbit/s Ethernet over twinaxial copper, electrical backplanes, single-mode and multi-mode optical fiber along with new 200 and 400 Gbit/s variants using 100 Gbit/s lanes.[30]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Fiber-optical cable
800GBASE-VR8 | 802.3df-2024 (167) | MPO-16 | eight pairs of OM5 multi-mode fiber, 53.125 GBd with PAM-4, for 50 m reach
800GBASE-SR8 | MPO-16 | eight pairs of OM5 multi-mode fiber, 53.125 GBd with PAM-4, for 100 m reach
800GBASE-DR8 | 802.3df-2024 (124) | MPO-16 | eight pairs of single-mode fiber, 53.125 GBd with PAM-4, for 2–500 m reach,
800GBASE-DR8-2 | MPO-16 | eight pairs of single-mode fiber, 53.125 GBd with PAM-4, for 2–2000 m reach
Other
800GBASE-CR8 | 802.3df-2024 (162) | QSFP-DD800
OSFP | eight lanes over twinax, 53.125 GBd with PAM-4, for 2 m reach
800GBASE-KR8 | 802.2df-2024 (163) |  | eight lanes over electrical backplane, 53.125 GBd with PAM-4,
800GBASE-R |  |  | As of April 2020[update], the PCS and PMA sublayers seem to be defined, using eight lanes of 100 Gbit/s each, and connecting with the transceiver module through a C2M or C2C interface defined in 802.3ck.[31]

### 1.6 Tbit/s

In December 2022, IEEE started the P802.3dj Task Force to define variants for 200, 400, 800 and 1600 Gbit/s over twinaxial copper, electrical backplanes, single-mode and multi-mode optical fiber along with new variants using 200 Gbit/s lanes.[32]

Name  | Standard (Clause)  | Common connectors  | Description

|
|
|

Fiber-optical cable
TBD | 802.3dj |  | eight pairs of single-mode fiber for 500 m reach
TBD |  | eight pairs of single-mode fiber for 2 km reach
Other
TBD | 802.3dj |  | eight twinaxial copper pairs for 1 meter reach

### First mile

Ethernet in the first mile provides Internet access service directly from providers to homes and small businesses.

Name  | Standard (Clause)  | Description

|
|

10BaseS  | Proprietary[33] | Ethernet over VDSL, used in Long Reach Ethernet products;[34] uses passband instead of the indicated baseband
2BASE-TL | 802.3ah-2004 (61&63)  | Over telephone wires
10PASS-TS  | 802.3ah-2004 (61&62)
100BASE-LX10  | 802.3ah-2004 (58)  | Single-mode fiber-optics
100BASE-BX10
1000BASE-LX10  | 802.3ah-2004 (59)
1000BASE-BX10
1000BASE-PX10  | 802.3ah-2004 (60)  | Passive optical network
1000BASE-PX20
10GBASE-PR
10/1GBASE-PRX | 802.3av-2009 (75)  | 10 Gbit/s passive optical network with 1 or 10 Gbit/s uplink for 10 or 20 km range
25GBASE-PR
50GBASE-PR | 802.3ca-2020 (141)  | 25 and 50 Gbit/s passive optical network

## Sublayers

Starting with Fast Ethernet, the physical layer specifications are divided into three sublayers in order to simplify design and interoperability:[35]

* PCS (Physical Coding Sublayer) - This sublayer performs auto-negotiation and basic encoding (e.g., 8b/10b), lane separation and recombination. For Ethernet, the bit rate at the top of the PCS is the nominal bit rate, e.g. 10 Mbit/s for classic Ethernet or 1000 Mbit/s for Gigabit Ethernet.
* PMA (Physical Medium Attachment sublayer) - This sublayer performs PMA framing, octet synchronization/detection, and polynomial scrambling/descrambling.
* PMD (Physical Medium Dependent sublayer) - This sublayer consists of a transceiver for the physical medium.

## Twisted-pair cable

Main article: Ethernet over twisted pair

Several varieties of Ethernet were specifically designed to run over 4-pair copper structured cabling already installed in many locations. In a departure from both 10BASE-T and 100BASE-TX, 1000BASE-T and above use all four cable pairs for simultaneous transmission in both directions through the use of echo cancellation.

Using point-to-point copper cabling provides the opportunity to deliver electrical power along with the data. This is called power over Ethernet and there are several variations defined in IEEE 802.3 standards. Combining 10BASE-T (or 100BASE-TX) with Mode A allows a hub or a switch to transmit both power and data over only two pairs. This was designed to leave the other two pairs free for analog telephone signals.[36] The pins used in Mode B supply power over the spare pairs not used by 10BASE-T and 100BASE-TX. 4PPoE defined in IEEE 802.3bt can use all four pairs to supply up to 100 W.

8P8C wiring (MDI)  Pin | Pair  | Color  | Telephone | 10BASE-T,[37] 100BASE-TX[38] | 1000BASE-T[39] onwards | PoE mode A | PoE mode B

|
|
|
|
|
|
|

1 | 3  |  white/green  |  | TX+ | BI_DA+ | 48 V out |
2 | 3  |  green  |  | TX− | BI_DA– | 48 V out |
3 | 2  |  white/orange  |  | RX+ | BI_DB+ | 48 V return |
4 | 1  |  blue  | ring | unused | BI_DC+ |  | 48 V out
5 | 1  |  white/blue  | tip | unused | BI_DC– |  | 48 V out
6 | 2  |  orange  |  | RX− | BI_DB– | 48 V return |
7 | 4  |  white/brown  |  | unused | BI_DD+ |  | 48 V return
8 | 4  |  brown  |  | unused | BI_DD– |  | 48 V return

The cable requirements depend on the transmission speed and the employed encoding method. Generally, faster speeds require both higher-grade cables and more sophisticated encoding.

## Minimum cable lengths

Some fiber connections have minimum cable lengths due to maximum level constraints on received signals.[40] Fiber ports designed for long-haul wavelengths may require a signal attenuator if used within a building.

10BASE2 installations, running on RG-58 coaxial cable, require a minimum of 0.5 m between stations tapped into the network cable to minimize reflections.[41]

10BASE-T, 100BASE-T, and 1000BASE-T installations running on twisted pair cable use a star topology. No minimum cable length is required for these networks.[42][43]

## Related standards

Some networking standards are not part of the IEEE 802.3 Ethernet standard, but support the Ethernet frame format, and are capable of interoperating with it.

* LattisNet—A SynOptics pre-standard twisted-pair 10 Mbit/s variant.
* 100BaseVG—An early contender for 100 Mbit/s Ethernet. It runs over four pairs of Category 3 cable but was not commercially successful.
* TIA 100BASE-SX—Promoted by the Telecommunications Industry Association. 100BASE-SX is an alternative implementation of 100 Mbit/s Ethernet over fiber; it is incompatible with the official 100BASE-FX standard. Its main feature is interoperability with 10BASE-FL, supporting autonegotiation between 10 and 100 Mbit/s operation – a feature lacking in the official standards due to the use of differing LED wavelengths. It was targeted at the installed base of 10 Mbit/s fiber networks.
* TIA 1000BASE-TX—Promoted by the Telecommunications Industry Association, it was a commercial failure. 1000BASE-TX uses a simpler protocol than the official 1000BASE-T standard so the electronics can be cheaper, but requires Category 6 cable.
* G.hn—A standard developed by ITU-T and promoted by HomeGrid Forum for high-speed (up to 1 Gbit/s) local area networks over existing home wiring (coaxial cables, power lines and phone lines). G.hn defines an Application Protocol Convergence (APC) layer that accepts Ethernet frames and encapsulates them into G.hn MSDUs.

Other networking standards do not use the Ethernet frame format but can still be connected to Ethernet using MAC-based bridging.

* 802.11—Standards for wireless local area networks (LANs), sold as Wi-Fi
* 802.16—Standards for wireless metropolitan area networks (MANs), sold as WiMAX

Other special-purpose physical layers include Avionics Full-Duplex Switched Ethernet and TTEthernet.

## References

1. ↑ "Configuring and Troubleshooting Ethernet 10/100/1000Mb Half/Full Duplex Auto-Negotiation". Cisco Systems. http://www.cisco.com/c/en/us/support/docs/lan-switching/ethernet/10561-3.html. "...it is possible for a link partner to detect the speed at which the other link partner operates, even though the other link partner is not configured for auto-negotiation. In order to detect the speed, the link partner senses the type of electrical signal that arrives and sees if it is 10 Mb or 100 Mb."
2. ↑ "Characteristics of 10GBASE-T Technology". fiber-optical-networking.com. 2017-11-08. http://www.fiber-optical-networking.com/characteristics-of-10gbase-t-technology.html.
3. ↑ "Consideration for 40 Gigabit Ethernet". IEEE HSSG. May 2007. https://grouper.ieee.org/groups/802/3/hssg/public/may07/duelk_01_0507.pdf.
4. ↑ "40 gigabit Ethernet answers". IEEE HSSG. May 2007. https://grouper.ieee.org/groups/802/3/hssg/public/may07/kipp_01_0507.pdf.
5. ↑ "HECTO: High-Speed Electro-Optical Components for Integrated Transmitter and Receiver in Optical Communication". Hecto.eu. http://www.hecto.eu/.
6. ↑ "IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force". IEEE. 2010-06-19. http://www.ieee802.org/3/ba/.40Gb/s+and+100Gb/s+Ethernet+Task+Force&rft.atitle=&rft.date=2010-06-19&rft.pub=IEEE&rft_id=http://www.ieee802.org/3/ba/&rfr_id=info:sid/en.wikibooks.org:Ethernet_physical_layer">
7. ↑ "IEEE P802.3df 400 Gb/s and 800 Gb/s Ethernet Task Force". IEEE. https://www.ieee802.org/3/df/public/index.html.400+Gb/s+and+800+Gb/s+Ethernet+Task+Force&rft.atitle=&rft.pub=IEEE&rft_id=https://www.ieee802.org/3/df/public/index.html&rfr_id=info:sid/en.wikibooks.org:Ethernet_physical_layer">
8. ↑ IEEE 802.3 1.2.3 Physical layer and media notation
9. ↑ IEEE 802.3 11.5.3 Delay requirements
10. ↑ 10.0 10.1 10.2 Zimmerman, Joann; Spurgeon, Charles (2014). Ethernet: The Definitive Guide, 2nd Edition. O'Reilly Media, Inc.. ISBN 978-1-4493-6184-6. http://proquest.safaribooksonline.com/book/networking/9781449362980/8dot-10-mb-s-ethernet/_10base_fl_fiber_optic_characteristics_html?uicode=vatech. Retrieved 28 February 2016. "This media system allowed multiple half-duplex Ethernet signal repeaters to be linked in series, exceeding the limit on the total number of repeaters that could be used in a given 10 Mb/s Ethernet system.... For the first few years after the standard was developed, equipment was available from a few vendors, but this equipment is no longer sold."
11. ↑ "The 100BASE-TX PMD (and MDI) is specified by incorporating the FDDI TP-PMD standard, ANSI X3.263: 1995 (TP-PMD), by reference, with the modifications noted below." (section 25.2 of IEEE802.3-2002).
12. ↑ 12.0 12.1 IEEE 802.3 66\. Extensions of the 10 Gb/s Reconciliation Sublayer (RS), 100BASE-X PHY, and 1000BASE-X PHY for unidirectional transport
13. ↑ IEEE 802.3 41\. Repeater for 1000 Mb/s baseband networks
14. ↑ "Cisco Gigabit Ethernet Solutions for Cisco 7x00 Series Routers". http://www.cisco.com/en/US/products/hw/modules/ps2033/products_data_sheet09186a0080091ce7.html.
15. ↑ IEEE 802.3 Table 52-6 10GBASE-S operating range for each optical fiber type
16. ↑ IEEE 802.3by 25 Gb/s Ethernet Task Force
17. ↑ "IEEE P802.3bq 25G/40GBASE-T Task Force". http://www.ieee802.org/3/bq/index.html.
18. ↑ "Approval of IEEE Std 802.3by-2016, IEEE Std 802.3bq-2016, IEEE Std 802.3bp-2016 and IEEE Std 802.3br-2016". IEEE. 2016-06-30. http://www.ieee802.org/3/NGBASET/email/msg00972.html.
19. ↑ 19.0 19.1 Reimer, Jeremy (July 25, 2007). "New Ethernet standard: not 40Gbps, not 100, but both". Ars Technica. https://arstechnica.com/hardware/news/2007/07/new-ethernet-standard-not-40-gbps-not-100-but-both.ars.
20. ↑ "IEEE P802.3bg 40Gb/s Ethernet: Single-mode Fibre PMD Task Force". official task force web site. IEEE 802. April 12, 2011. http://www.ieee802.org/3/bg/.40Gb/s+Ethernet:+Single-mode+Fibre+PMD+Task+Force&rft.atitle=official+task+force+web+site&rft.date=April+12,+2011&rft.pub=IEEE+802&rft_id=http://www.ieee802.org/3/bg/&rfr_id=info:sid/en.wikibooks.org:Ethernet_physical_layer">
21. ↑ Ilango Ganga (May 13, 2009). "Chief Editor's Report". IEEE P802.3ba 40Gb/s and 100Gb/s Ethernet Task Force public record. p. 8. http://www.ieee802.org/3/ba/public/may08/ganga_02_0508.pdf.40Gb/s+and+100Gb/s+Ethernet+Task+Force+public+record&rft.aulast=Ilango+Ganga&rft.au=Ilango+Ganga&rft.date=May+13,+2009&rft.pages=p.+8&rft_id=http://www.ieee802.org/3/ba/public/may08/ganga_02_0508.pdf&rfr_id=info:sid/en.wikibooks.org:Ethernet_physical_layer">
22. ↑ 22.0 22.1 22.2 "IEEE 802.3 50 Gb/s, 100 Gb/s, and 200 Gb/s Ethernet Task Force". IEEE 802.3. 2016-05-17. http://www.ieee802.org/3/cd/.50+Gb/s,+100+Gb/s,+and+200+Gb/s+Ethernet+Task+Force&rft.atitle=&rft.date=2016-05-17&rft.pub=IEEE+802.3&rft_id=http://www.ieee802.org/3/cd/&rfr_id=info:sid/en.wikibooks.org:Ethernet_physical_layer">
23. ↑ 23.0 23.1 23.2 "IEEE P802.3ck 100 Gb/S, 200 Gb/S, and 400 Gb/S Electrical Interfaces Task Force". http://www.ieee802.org/3/ck/.100+Gb/S,+200+Gb/S,+and+400+Gb/S+Electrical+Interfaces+Task+Force&rft.atitle=&rft_id=http://www.ieee802.org/3/ck/&rfr_id=info:sid/en.wikibooks.org:Ethernet_physical_layer">
24. ↑ 24.0 24.1 24.2 Kochuparambil, Beth (21 September 2022). "[802.3_100GEL] FW: IEEE Std 802.3ck-2022, IEEE Std 802.3cs-2022, IEEE Std 802.3db-2022 and IEEE Std 802.3de-2022 approval". STDS-802-3-100GEL (Mailing list).
25. ↑ 25.0 25.1 "[STDS-802-3-400G IEEE P802.3bs Approved!"]. IEEE 802.3bs Task Force. http://www.ieee802.org/3/400GSG/email/msg01519.html.
26. ↑ Snyder, Bob. "IEEE Begins Work on New Ethernet Standard". http://www.proavbiz-europe.com/index.php?option=com_content&view=article&id=6151:ieee-begins-work-on-new-ethernet-standard&catid=15&Itemid=401979.
27. ↑ "Bob Metcalfe on the Terabit Ethernet". Light Reading. February 15, 2008. http://www.lightreading.com/video.asp?section_id=154&doc_id=703860.
28. ↑ "IEEE to introduce new Ethernet speed, up to 1Tb per second - MacNN". http://www.electronista.com/articles/12/08/20/aging.standard.is.still.ahead.of.most.core.networking/.
29. ↑ "25 Gigabit Ethernet Consortium Rebrands to Ethernet Technology Consortium; Announces 800 Gigabit Ethernet (GbE) Specification". 2020-04-06. https://ethernettechnologyconsortium.org/press-room/press-releases/25-gigabit-ethernet-consortium-rebrands-to-ethernet-technology-consortium-announces-800-gigabit-ethernet-gbe-specification-152/.
30. ↑ "Objectives IEEE 802.3 802.3df Task Force". 2021-12-10. https://www.ieee802.org/3/df/proj_doc/objectives_P802d3df_211118.pdf.
31. ↑ "800GSpecification". 2020-03-10. https://ethernettechnologyconsortium.org/wp-content/uploads/2020/03/800G-Specification_r1.0.pdf.
32. ↑ "Adopted IEEE P802.3dj Objectives". https://www.ieee802.org/3/dj/projdoc/objectives_P802d3dj_240314.pdf.
33. ↑ "Infineon Strengthens Leadership in MDU/MTU Market with Ethernet over VDSL Technology Patent Award". News release (Infineon Technologies AG). January 8, 2001. http://www.infineon.com/news/press/101_031e.htm.
34. ↑ "Infineon Announces Second Quarter Results". News release (Infineon Technologies). April 24, 2001. http://www.infineon.com/cms/en/corporate/press/news/releases/2001/130817.html. "...strategic design-win with Cisco for new long-range Ethernet products incorporating Infineon's 10BaseS technology"
35. ↑ IEEE 802.3 Figure 1–1—IEEE 802.3 standard relationship to the ISO/IEC Open Systems Interconnection (OSI) reference model
36. ↑ "Tech Info - LAN and Telephones". Zytrax.com. http://www.zytrax.com/tech/layer_1/cables/mixed.html.
37. ↑ IEEE 802.3 14.5.1 MDI connectors
38. ↑ IEEE 802.3 Table 25–2—Twisted-pair MDI contact assignments
39. ↑ IEEE 802.3 40.8.1 MDI connectors
40. ↑ "Cisco 100BASE-FX SFP Fast Ethernet Interface Converter on Gigabit SFP Ports". Cisco Systems. http://www.cisco.com/en/US/products/hw/modules/ps5455/products_data_sheet0900aecd801ba88e.html.
41. ↑ "IEEE Standard for Ethernet 802.3-2008 Clauses 10.7.2.1-2". http://www.trincoll.edu/Academics/MajorsAndMinors/Engineering/Documents/IEEE Standard for Ethernet.pdf.
42. ↑ "Troubleshooting Ethernet Collisions". http://www.cisco.com/c/en/us/support/docs/interfaces-modules/port-adapters/12768-eth-collisions.html.
43. ↑ Gigabit Ethernet, http://web.cs.dal.ca/~yongzhen/course/6704/report.pdf, retrieved 2016-08-09

## External links

* IEEE GET Program GET 802(R) Standards
* IEEE 802.3 Ethernet Working Group

* v
* t
* e

Ethernet family of local area network technologies

Speeds|

* 10 Mbit/s
* 100 Mbit/s
* 1 Gbit/s
* 2.5 and 5 Gbit/s
* 10 Gbit/s
* 25 and 50 Gbit/s
* 40 and 100 Gbit/s
* 200 and 400 Gbit/s

General|

* Physical layer
* Autonegotiation
* EtherType
* Flow control
* Frames
* Jumbos

Organizations|

* IEEE 802.3
* Ethernet Alliance

Media|

* Twisted pair
* Coaxial
* First mile
* 10G-EPON

Historic|

* CSMA/CD
* StarLAN
* 10BROAD36
* 10BASE-FB
* 10BASE-FL
* 10BASE5
* 10BASE2
* FOIRL
* 100BaseVG
* LattisNet
* Long Reach

Applications|

* Audio
* Carrier
* Data center
* Energy Efficiency
* Industrial
* Metro
* Power
* Synchronous

Transceivers|

* MAU
* GBIC
* SFP/SFP+/QSFP/QSFP+/OSFP
* XENPAK
* XFP
* CFP

Interfaces|

* AUI
* MDI
* MII
* GMII
* XGMII
* XAUI

* Category
* Commons

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Ethernet physical layer. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Ethernet_physical_layer&oldid=4299469"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template