Standard cost accounting

Short description: Cost accounting method utilizing efficiencies

Standard cost accounting is a traditional cost accounting method introduced in the 1920s,[1] as an alternative for the traditional cost accounting method based on historical costs.[2][3]

## Contents

* 1 Overview
* 2 History
* 3 Standard cost accounting, topics
* 3.1 Historical costs
* 3.2 Variance analysis
* 4 See also
* 5 References
* 6 Further reading

## Overview

Standard cost accounting uses ratios called efficiencies that compare the labor and materials actually used to produce a good with those that the same goods would have required under "standard" conditions. As long as actual and standard conditions are similar, few problems arise. Unfortunately, standard cost accounting methods developed about 100 years ago, when labor comprised the most important cost of manufactured goods. Standard methods continue to emphasize labor efficiency even though that resource now constitutes a (very) small part of the cost in most cases. [4]

Standard cost accounting can hurt managers, workers, and firms in several ways. For example, a policy decision to increase inventory can harm a manufacturing manager's performance evaluation. Increasing inventory requires increased production, which means that processes must operate at higher rates. When something goes wrong, the process takes longer and uses more than the standard labor time. The manager appears responsible for the excess, even though they have no control over the production requirement or the problem.

In adverse economic times, firms use the same efficiencies to downsize, right size, or otherwise reduce their labor force. Workers laid off, under those circumstances, have even less control over excess inventory and cost efficiencies than their managers.

Many financial and cost accountants have agreed on the desirability of replacing standard cost accounting . They have not, however, found a successor.

## History

One of the first authors to foresee standard costing was the British accountant George P. Norton in his 1889 Textile Manufacturers' Bookkeeping.[5] John Whitmore, a disciple of Alexander Hamilton Church, is credited for actually presenting "...the first detailed description of a standard cost system..."[6] in 1906/08. The Anglo-American management consultant G. Charter Harrison is credited for designing one of the earliest known complete standard cost systems in the early 1910s.[7]

When cost accounting was developed in the 1890s, labor was the largest fraction of product cost and could be considered a variable cost. Workers often did not know how many hours they would work in a week when they reported on Monday morning because time-keeping systems (based in time book) were rudimentary. Cost accountants, therefore, concentrated on how efficiently managers used labor since it was their most important variable resource. Now, however, workers who come to work on Monday morning almost always work 40 hours or more; their cost is fixed rather than variable. However, today, many managers are still evaluated on their labor efficiencies, and many downsizing, rightsizing, and other labor reduction campaigns are based on them.

Traditional standard costing (TSC), used in cost accounting, dates back to the 1920s and is a central method in management accounting practiced today because it is used for financial statement reporting for the valuation of an income statement and balance sheets line items such as the cost of goods sold (COGS) and inventory valuation. Traditional standard costing must comply with generally accepted accounting principles (GAAP) and actually aligns itself more with answering financial accounting requirements rather than providing solutions for management accountants. Traditional approaches limit themselves by defining cost behavior only in terms of production or sales volume.

## Standard cost accounting, topics

### Historical costs

Historical costs are costs whereby materials and labor may be allocated based on past experience. Historical costs are costs incurred in the past. Predetermined costs are computed in advance on basis of factors affecting cost elements.

In modern cost account of recording historical costs was taken further, by allocating the company's fixed costs over a given period of time to the items produced during that period, and recording the result as the total cost of production. This allowed the full cost of products that were not sold in the period they were produced to be recorded in inventory using a variety of complex accounting methods, which was consistent with the principles of Generally Accepted Accounting Principles (GAAP). It also essentially enabled managers to ignore the fixed costs, and look at the results of each period in relation to the "standard cost" for any given product.

For example: if the railway coach company normally produced 40 coaches per month, and the fixed costs were still $1000/month, then each coach could be said to incur an Operating Cost/overhead of $25 =($1000 / 40). Adding this to the variable costs of $300 per coach produced a full cost of $325 per coach.

This method tended to slightly distort the resulting unit cost, but in mass-production industries that made one product line, and where the fixed costs were relatively low, the distortion was very minor.

For example: if the railway coach company made 100 coaches one month, then the unit cost would become $310 per coach ($300 + ($1000 / 100)). If the next month the company made 50 coaches, then the unit cost = $320 per coach ($300 + ($1000 / 50)), a relatively minor difference.

### Variance analysis

An important part of standard cost accounting is a variance analysis, which breaks down the variation between actual cost and standard costs into various components (volume variation, material cost variation, labor cost variation, etc.) so managers can understand why costs were different from what was planned and take appropriate action to correct the situation.

## See also

* Management accounting

## References

1. ↑ Richard Vangermeersch. "Control: Classic model," in: History of Accounting: An International Encyclopedia. Michael Chatfield, Richard Vangermeersch eds. 1996/2014. p. 174-75.
2. ↑ Thomas Downie (1927). The mechanism of standard (or predetermined) cost accounting and efficiency records. p. 7, p. 54
3. ↑ Adolph Matz (1962) Cost accounting. p. 584.
4. ↑ Statler, Elaine; Grabel, Joyce (2016). "2016". The Master Guide to Controllers' Best Practices. 10 Paragon Drive, Suite 1, Montvale, NJ 07645-1760: The Association of Acccountants and Financial Professionals in Business. p. 352. ISBN 978-0-996-72932-1. ".
5. ↑ Solomons, David. "Costing Pioneers: Some Links with the Past*." The Accounting Historians Journal 21.2 (1994): 136.
6. ↑ Michael Chatfield. "Whitmore, John," in: History of Accounting: An International Encyclopedia. Michael Chatfield, Richard Vangermeersch eds. 1996/2014. p. 607-8.
7. ↑ Michael Chatfield. "Harrison, G. Charter 1881-," in: Michael Chatfield, Richard Vangermeersch (eds.), The History of Accounting (RLE Accounting): An International Encyclopedia 2014\. p. 291.

## Further reading

* Cheatham, Carole B., and Leo R. Cheatham. "Redesigning cost systems: Is standard costing obsolete?." Accounting Horizons 10 (1996): 23-31.
* Epstein, Marc J. The effect of scientific management on the development of the standard cost system. New York: Arno Press, 1978.
* Fleischman, Richard K., and Thomas N. Tyson. "The evolution of standard costing in the UK and US: from decision making to control." Abacus 34.1 (1998): 92-119.
* Henrici, Stanley B. Standard costs for manufacturing. McGraw-Hill, 1960.
* Nicholson, Jerome Lee, and John Francis Deems Rohrbach. Cost accounting. New York: Ronald Press, 1919.

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Standard cost accounting. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Finance:Standard_cost_accounting&oldid=4189767"