Two-phase electric power

Short description: Electric power distribution system

A simplified diagram of a two-phase alternator[1]

Two-phase electrical power was an early 20th-century polyphase alternating current electric power distribution system. Two circuits were used, with voltage phases differing by one-quarter of a cycle, 90°. Usually circuits used four wires, two for each phase. Less frequently, three wires were used, with a common wire with a larger-diameter conductor. Some early two-phase generators had two complete rotor and field assemblies, with windings physically offset to provide two-phase power. The generators at Niagara Falls installed in 1895 were the largest generators in the world at that time, and were two-phase machines. Three-phase systems eventually replaced the original two-phase power systems for power transmission and utilization. Active two-phase distribution systems remain in Center City Philadelphia, where many commercial buildings are permanently wired for two-phase,[2] and in Hartford, Connecticut.[3]

## Contents

* 1 Comparison with single-phase power
* 2 Comparison with three-phase power
* 3 See also
* 4 References

## Comparison with single-phase power

The advantage of two-phase electrical power over single-phase was that it allowed for simple, self-starting electric motors. In the early days of electrical engineering, it was easier to analyze and design two-phase systems where the phases were completely separated.[4] It was not until the invention of the method of symmetrical components in 1918 that polyphase power systems had a convenient mathematical tool for describing unbalanced load cases. The revolving magnetic field produced with a two-phase system allowed electric motors to provide torque from zero motor speed, which was not possible with a single-phase induction motor (without an additional starting means). Induction motors designed for two-phase operation use a similar winding configuration as capacitor start single-phase motors. However, in a two-phase induction motor, the impedances of the two windings are identical.

Two-phase circuits also have the advantage of constant combined power into an ideal load, whereas power in a single-phase circuit pulsates at twice the line frequency due to the zero crossings of voltage and current.

## Comparison with three-phase power

Three-phase electric power requires less conductor mass for the same voltage and overall power, compared with a two-phase four-wire circuit of the same carrying capacity.[5] It has replaced two-phase power for commercial distribution of electrical energy, but two-phase circuits are still found in certain control systems.

Two-phase circuits typically use two separate pairs of current-carrying conductors. Alternatively, three wires may be used, but the common conductor carries the vector sum of the phase currents, which requires a larger conductor. The vector sum of balanced three-phase currents, however, is zero, allowing for the neutral wires to be eliminated. In electrical power distribution, a requirement of only three conductors, rather than four, represented a considerable distribution-wire cost savings due to the expense of conductors and installation.

While both two-phase and three-phase circuits have a constant combined power for an ideal load, practical devices such as motors can suffer from power pulsations in two-phase systems.[4] These power pulsations tend to cause increased mechanical noise in transformer and motor laminations due to magnetostriction and torsional vibration in generator and motor drive shafts.

Two-phase power can be derived from a three-phase source using two transformers in a Scott connection: One transformer primary is connected across two phases of the supply. The second transformer is connected to a center-tap of the first transformer, and is wound for 86.6% of the phase-to-phase voltage on the three-phase system. The secondaries of the transformers will have two phases 90 degrees apart in time, and a balanced two-phase load will be evenly balanced over the three supply phases.

## See also

* Polyphase system
* Rotary converter
* Single-phase electric power
* Split-phase electric power
* Three-phase electric power

## References

Notes

Specific references

1. ↑ Figure 1253 from the 1917 Hawkins Electrical Guide
2. ↑ Company advertising services for two-phase: http://www.phillyfacility.com/two_phase.htm
3. ↑ Williams, Al (2018-03-15). "A Tale Of Two Phases And Tech Inertia" (in en-US). https://hackaday.com/2018/03/15/a-tale-of-two-phases-and-tech-inertia/.
4. ↑ 4.0 4.1 Blalock, T.J. (March 2004). "The first polyphase system a look back at two-phase power for AC distribution". IEEE Power and Energy Magazine 2 (2): 63–66. doi:10.1109/MPAE.2004.1269626.
5. ↑ Terrell Croft and Wilford Summers (ed), American Electricans' Handbook, Eleventh Edition, McGraw Hill, New York (1987) ISBN:0-07-013932-6 page 3–10, figure 3–23

General references

* Donald G. Fink and H. Wayne Beaty, Standard Handbook for Electrical Engineers, Eleventh Edition, McGraw-Hill, New York, 1978, ISBN:0-07-020974-X
* Edwin J. Houston and Arthur Kennelly, Recent Types of Dynamo-Electric Machinery, copyright American Technical Book Company 1897, published by P. F. Collier and Sons New York, 1902

* v
* t
* e

Electric machines

* AC - Alternating current
* DC - Direct current
* PM - Permanent magnet
* SC - Self-commutated

Components and
accessories

* Armature
* Braking chopper
* Brush
* Commutator
* DC injection braking
* Field coil
* Rotor
* Slip ring
* Stator
* Winding

Generators|

* Alternator
* Electric generator

Motors|

* AC motor
* Induction motor
* Shaded-pole
* Dahlander pole changing motor
* Wound-rotor (WRIM)
* Linear induction
* Synchronous motor
* Repulsion
* DC motor
* Homopolar
* Brushed DC electric motor
* Brushless DC electric motor
* Unipolar
* Universal
* Switched reluctance (SRM)
* Reluctance
* Doubly-fed
* Linear
* Servomotor
* Stepper
* Traction
* Electrostatic
* Piezoelectric
* Ultrasonic
* TEFC
* Axial flux

Motor controllers|

* AC-to-AC converter
* Cycloconverter
* Amplidyne
* Drives
* Variable-frequency drive
* Direct torque control
* Vector control
* Metadyne
* Motor soft starter
* Ward Leonard control

History, education,
recreational use

* Timeline of the electric motor
* Ball bearing motor
* Barlow's wheel
* Lynch motor
* Mendocino motor
* Mouse mill motor

Experimental, futuristic|

* Coilgun
* Railgun
* Superconducting machine

Related topics|

* Blocked-rotor test
* Circle diagram
* Electromagnetism
* Open-circuit test
* Open-loop controller
* Power-to-weight ratio
* Two-phase system
* Inchworm motor
* Starter
* Voltage controller

People|

* Arago
* Barlow
* Botto
* Davenport
* Davidson
* Dolivo-Dobrovolsky
* Faraday
* Ferraris
* Gramme
* Henry
* Jacobi
* Jedlik
* Lenz
* Maxwell
* Ørsted
* Park
* Pixii
* Saxton
* Siemens
* Sprague
* Steinmetz
* Sturgeon
* Tesla

0.00

(0 votes)

Original source: https://en.wikipedia.org/wiki/Two-phase electric power. Read more

|

Retrieved from "https://handwiki.org/wiki/index.php?title=Physics:Two-phase_electric_power&oldid=3280054"
*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template