Electrical resistance and conductance

Opposition to the passage of an electric current

This article is about specific applications of conductivity and resistivity in electrical elements. For other types of conductivity, see Conductivity. For electrical conductivity in general, see Electrical resistivity and conductivity.

"Resistive" redirects here. For the term used when referring to touchscreens, see Resistive touchscreen.

Articles about

Electromagnetism
Solenoid

* Electricity
* Magnetism
* History
* Textbooks

Electrostatics

* Electric charge
* Coulomb's law
* Conductor
* Charge density
* Permittivity
* Electric dipole moment
* Electric field
* Electric potential
* Electric flux / potential energy
* Electrostatic discharge
* Gauss's law
* Induction
* Insulator
* Polarization density
* Static electricity
* Triboelectricity

Magnetostatics

* Ampère's law
* Biot–Savart law
* Gauss's law for magnetism
* Magnetic field
* Magnetic flux
* Magnetic dipole moment
* Magnetic permeability
* Magnetic scalar potential
* Magnetization
* Magnetomotive force
* Magnetic vector potential
* Right-hand rule

Electrodynamics

* Lorentz force law
* Electromagnetic induction
* Faraday's law
* Lenz's law
* Displacement current
* Maxwell's equations
* Electromagnetic field
* Electromagnetic pulse
* Electromagnetic radiation
* Maxwell tensor
* Poynting vector
* Liénard–Wiechert potential
* Jefimenko's equations
* Eddy current
* London equations

* Mathematical descriptions of the electromagnetic field

Electrical network

* Alternating current
* Capacitance
* Direct current
* Electric current
* Electrolysis
* Current density
* Joule heating
* Electromotive force
* Impedance
* Inductance
* Ohm's law
* Parallel circuit
* Resistance
* Resonant cavities
* Series circuit
* Voltage
* Waveguides

Covariant formulation

* Electromagnetic tensor
(stress–energy tensor)

* Four-current
* Electromagnetic four-potential

Scientists

* Ampère
* Biot
* Coulomb
* Davy
* Einstein
* Faraday
* Fizeau
* Gauss
* Heaviside
* Henry
* Hertz
* Hopkinson
* Jefimenko
* Joule
* Lenz
* Liénard
* Lorentz
* Maxwell
* Neumann
* Ørsted
* Ohm
* Poynting
* Ritchie
* Savart
* Singer
* Steinmetz
* Tesla
* Thomson
* Volta
* Weber
* Wiechert
* Poisson

* v
* t
* e

The electrical resistance of an object is a measure of its opposition to the flow of electric current. Its reciprocal quantity is electrical conductance, measuring the ease with which an electric current passes. Electrical resistance shares some conceptual parallels with mechanical friction. The SI unit of electrical resistance is the ohm (Ω), while electrical conductance is measured in siemens (S) (formerly called the 'mho' and then represented by ℧).

The resistance of an object depends in large part on the material it is made of. Objects made of electrical insulators like rubber tend to have very high resistance and low conductance, while objects made of electrical conductors like metals tend to have very low resistance and high conductance. This relationship is quantified by resistivity or conductivity. The nature of a material is not the only factor in resistance and conductance, however; it also depends on the size and shape of an object because these properties are extensive rather than intensive. For example, a wire's resistance is higher if it is long and thin, and lower if it is short and thick. All objects resist electrical current, except for superconductors, which have a resistance of zero.

The resistance R of an object is defined as the ratio of voltage V across it to current I through it, while the conductance G is the reciprocal: Failed to parse (Conversion error. Server ("https://wikimedia.org/api/rest_") reported: "Cannot get mml. Server problem."): {\displaystyle R={\frac {V}{I}},\qquad G={\frac {I}{V}}={\frac {1}{R}}}

For a wide variety of materials and conditions, V and I are directly proportional to each other, and therefore R and G are constants (although they will depend on the size and shape of the object, the material it is made of, and other factors like temperature or strain). This proportionality is called Ohm's law, and materials that satisfy it are called ohmic materials.

In other cases, such as a transformer, diode or battery, V and I are not directly proportional. The ratio V/I is sometimes still useful, and is referred to as a chordal resistance or static resistance,[1][2] since it corresponds to the inverse slope of a chord between the origin and an I–V curve. In other situations, the derivative d V d I {\textstyle {\frac {\mathrm {d} V}{\mathrm {d} I}}} may be most useful; this is called the differential resistance.

## Contents

* 1 Introduction
* 2 Conductors and resistors
* 3 Ohm's law
* 4 Relation to resistivity and conductivity
* 5 Measurement
* 6 Typical values
* 7 Static and differential resistance
* 8 AC circuits
* 8.1 Impedance and admittance
* 8.2 Frequency dependence
* 9 Energy dissipation and Joule heating
* 10 Dependence on other conditions
* 10.1 Temperature dependence
* 10.2 Strain dependence
* 10.3 Light illumination dependence
* 11 Superconductivity
* 12 See also
* 13 Footnotes
* 14 References
* 15 External links

## Introduction[edit | edit source]

File:ResistanceHydraulicAnalogy.svg

The hydraulic analogy compares electric current flowing through circuits to water flowing through pipes. When a pipe (left) is filled with hair (right), it takes a larger pressure to achieve the same flow of water. Pushing electric current through a large resistance is like pushing water through a pipe clogged with hair: It requires a larger push (electromotive force) to drive the same flow (electric current).

In the hydraulic analogy, current flowing through a wire (or resistor) is like water flowing through a pipe, and the voltage drop across the wire is like the pressure drop that pushes water through the pipe. Conductance is proportional to how much flow occurs for a given pressure, and resistance is proportional to how much pressure is required to achieve a given flow.

The voltage drop (i.e., difference between voltages on one side of the resistor and the other), not the voltage itself, provides the driving force pushing current through a resistor. In hydraulics, it is similar: the pressure difference between two sides of a pipe, not the pressure itself, determines the flow through it. For example, there may be a large water pressure above the pipe, which tries to push water down through the pipe. But there may be an equally large water pressure below the pipe, which tries to push water back up through the pipe. If these pressures are equal, no water flows. (In the image at right, the water pressure below the pipe is zero.)

The resistance and conductance of a wire, resistor, or other element is mostly determined by two properties:

* geometry (shape), and
* material

Geometry is important because it is more difficult to push water through a long, narrow pipe than a wide, short pipe. In the same way, a long, thin copper wire has higher resistance (lower conductance) than a short, thick copper wire.

Materials are important as well. A pipe filled with hair restricts the flow of water more than a clean pipe of the same shape and size. Similarly, electrons can flow freely and easily through a copper wire, but cannot flow as easily through a steel wire of the same shape and size, and they essentially cannot flow at all through an insulator like rubber, regardless of its shape. The difference between copper, steel, and rubber is related to their microscopic structure and electron configuration, and is quantified by a property called resistivity.

In addition to geometry and material, there are various other factors that influence resistance and conductance, such as temperature; see below.

## Conductors and resistors[edit | edit source]

A 75 Ω resistor, as identified by its electronic color code (violet–green–black–gold–red). An ohmmeter could be used to verify this value.

Substances in which electricity can flow are called conductors. A piece of conducting material of a particular resistance meant for use in a circuit is called a resistor. Conductors are made of high-conductivity materials such as metals, in particular copper and aluminium. Resistors, on the other hand, are made of a wide variety of materials depending on factors such as the desired resistance, amount of energy that it needs to dissipate, precision, and costs.

## Ohm's law[edit | edit source]

Main article: Ohm's law

File:FourIVcurves.svg

The current–voltage characteristics of four devices: Two resistors, a diode, and a battery. The horizontal axis is voltage drop, the vertical axis is current. Ohm's law is satisfied when the graph is a straight line through the origin. Therefore, the two resistors are ohmic, but the diode and battery are not.

For many materials, the current I through the material is proportional to the voltage V applied across it:

I ∝ V {\displaystyle I\propto V}

over a wide range of voltages and currents. Therefore, the resistance and conductance of objects or electronic components made of these materials is constant. This relationship is called Ohm's law, and materials which obey it are called ohmic materials. Examples of ohmic components are wires and resistors. The current–voltage graph of an ohmic device consists of a straight line through the origin with positive slope.

Other components and materials used in electronics do not obey Ohm's law; the current is not proportional to the voltage, so the resistance varies with the voltage and current through them. These are called nonlinear or non-ohmic. Examples include diodes and fluorescent lamps. The current-voltage curve of a nonohmic device is a curved line.

## Relation to resistivity and conductivity[edit | edit source]

Main article: Electrical resistivity and conductivity

File:Resistivity geometry.png

A piece of resistive material with electrical contacts on both ends.

The resistance of a given object depends primarily on two factors: what material it is made of, and its shape. For a given material, the resistance is inversely proportional to the cross-sectional area; for example, a thick copper wire has lower resistance than an otherwise-identical thin copper wire. Also, for a given material, the resistance is proportional to the length; for example, a long copper wire has higher resistance than an otherwise-identical short copper wire. The resistance R and conductance G of a conductor of uniform cross section, therefore, can be computed as

Failed to parse (Conversion error. Server ("https://wikimedia.org/api/rest_") reported: "Cannot get mml. Server problem."): {\displaystyle {\begin{aligned}R&=\rho {\frac {\ell }{A}},\\\\[5pt]G&=\sigma {\frac {A}{\ell }}\,.\end{aligned}}}

where  ℓ {\displaystyle \ell } is the length of the conductor, measured in metres (m), A is the cross-sectional area of the conductor measured in square metres (m2), σ (sigma) is the electrical conductivity measured in siemens per meter (S·m−1), and ρ (rho) is the electrical resistivity (also called specific electrical resistance) of the material, measured in ohm-metres (Ω·m). The resistivity and conductivity are proportionality constants, and therefore depend only on the material the wire is made of, not the geometry of the wire. Resistivity and conductivity are reciprocals: Failed to parse (Conversion error. Server ("https://wikimedia.org/api/rest_") reported: "Cannot get mml. Server problem."): {\displaystyle \rho =1/\sigma } . Resistivity is a measure of the material's ability to oppose electric current.

This formula is not exact, as it assumes the current density is totally uniform in the conductor, which is not always true in practical situations. However, this formula still provides a good approximation for long thin conductors such as wires.

Another situation for which this formula is not exact is with alternating current (AC), because the skin effect inhibits current flow near the center of the conductor. For this reason, the geometrical cross-section is different from the effective cross-section in which current actually flows, so resistance is higher than expected. Similarly, if two conductors near each other carry AC current, their resistances increase due to the proximity effect. At commercial power frequency, these effects are significant for large conductors carrying large currents, such as busbars in an electrical substation,[3] or large power cables carrying more than a few hundred amperes.

The resistivity of different materials varies by an enormous amount: For example, the conductivity of teflon is about 1030 times lower than the conductivity of copper. Loosely speaking, this is because metals have large numbers of "delocalized" electrons that are not stuck in any one place, so they are free to move across large distances. In an insulator, such as Teflon, each electron is tightly bound to a single molecule so a great force is required to pull it away. Semiconductors lie between these two extremes. More details can be found in the article: Electrical resistivity and conductivity. For the case of electrolyte solutions, see the article: Conductivity (electrolytic).

Resistivity varies with temperature. In semiconductors, resistivity also changes when exposed to light. See below.

## Measurement[edit | edit source]

Main article: Ohmmeter

File:Sanwa SM-1005s.jpg

An ohmmeter

An instrument for measuring resistance is called an ohmmeter. Simple ohmmeters cannot measure low resistances accurately because the resistance of their measuring leads causes a voltage drop that interferes with the measurement, so more accurate devices use four-terminal sensing.

## Typical values[edit | edit source]

See also: Electrical resistivities of the elements (data page) and Electrical resistivity and conductivity

Typical resistance values for selected objects  Component  | Resistance (Ω)

|

1 meter of copper wire with 1 mm diameter  | 0.02[a]
1 km overhead power line (typical)  | 0.03[5]
AA battery (typical internal resistance)  | 0.1[b]
Incandescent light bulb filament (typical)  | 200–1000[c]
Human body  | 1000–100,000[d]

## Static and differential resistance[edit | edit source]

See also: Small-signal model

File:DifferentialChordalResistance.svg

The current–voltage curve of a non-ohmic device (purple). The static resistance at point A is the inverse slope of line B through the origin. The differential resistance at A is the inverse slope of tangent line C.

File:Negative differential resistance.svg

The current–voltage curve of a component with negative differential resistance, an unusual phenomenon where the current–voltage curve is non-monotonic.

Many electrical elements, such as diodes and batteries do not satisfy Ohm's law. These are called non-ohmic or non-linear, and their current–voltage curves are not straight lines through the origin.

Resistance and conductance can still be defined for non-ohmic elements. However, unlike ohmic resistance, non-linear resistance is not constant but varies with the voltage or current through the device; i.e., its operating point. There are two types of resistance:[1][2]

Static resistance

Also called chordal or DC resistance

This corresponds to the usual definition of resistance; the voltage divided by the current Failed to parse (Conversion error. Server ("https://wikimedia.org/api/rest_") reported: "Cannot get mml. Server problem."): {\displaystyle R_{\mathrm {static} }={\frac {U}{I}}\,.} It is the slope of the line (chord) from the origin through the point on the curve. Static resistance determines the power dissipation in an electrical component. Points on the current–voltage curve located in the 2nd or 4th quadrants, for which the slope of the chordal line is negative, have negative static resistance. Passive devices, which have no source of energy, cannot have negative static resistance. However active devices such as transistors or op-amps can synthesize negative static resistance with feedback, and it is used in some circuits such as gyrators.
Differential resistance

Also called dynamic, incremental, or small-signal resistance

Differential resistance is the derivative of the voltage with respect to the current; the slope of the current–voltage curve at a point Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle R_\mathrm{diff} = \frac { {\mathrm d}U}{ {\mathrm d}I} \,.} If the current–voltage curve is nonmonotonic (with peaks and troughs), the curve has a negative slope in some regions—so in these regions the device has negative differential resistance. Devices with negative differential resistance can amplify a signal applied to them, and are used to make amplifiers and oscillators. These include tunnel diodes, Gunn diodes, IMPATT diodes, magnetron tubes, and unijunction transistors.

## AC circuits[edit | edit source]

### Impedance and admittance[edit | edit source]

Main articles: Electrical impedance and Admittance

File:VI phase.svg

The voltage (red) and current (blue) versus time (horizontal axis) for a capacitor (top) and inductor (bottom). Since the amplitude of the current and voltage sinusoids are the same, the absolute value of impedance is 1 for both the capacitor and the inductor (in whatever units the graph is using). On the other hand, the phase difference between current and voltage is −90° for the capacitor; therefore, the complex phase of the impedance of the capacitor is −90°. Similarly, the phase difference between current and voltage is +90° for the inductor; therefore, the complex phase of the impedance of the inductor is +90°.

When an alternating current flows through a circuit, the relation between current and voltage across a circuit element is characterized not only by the ratio of their magnitudes, but also the difference in their phases. For example, in an ideal resistor, the moment when the voltage reaches its maximum, the current also reaches its maximum (current and voltage are oscillating in phase). But for a capacitor or inductor, the maximum current flow occurs as the voltage passes through zero and vice versa (current and voltage are oscillating 90° out of phase, see image below). Complex numbers are used to keep track of both the phase and magnitude of current and voltage:

Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \begin{array}{cl} u(t) &= \mathfrak{Re}\left(U_0 \cdot e^{j\omega t}\right) \\\ i(t) &= \mathfrak{Re}\left(I_0 \cdot e^{j(\omega t + \varphi)}\right) \\\ Z &= \frac{U}{I} \\\ Y &= \frac{1}{Z} = \frac{I}{U} \end{array}}

where:

* t is time;
* u(t) and i(t) are the voltage and current as a function of time, respectively;
* U0 and I0 indicate the amplitude of the voltage and current, respectively;
* Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \omega} is the angular frequency of the AC current;
* Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \varphi} is the displacement angle;
* U and I are the complex-valued voltage and current, respectively;
* Z and Y are the complex impedance and admittance, respectively;
* Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \mathfrak{Re}} indicates the real part of a complex number; and
* Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle j=\sqrt{-1}} is the imaginary unit.

The impedance and admittance may be expressed as complex numbers that can be broken into real and imaginary parts: Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \begin{align} Z &= R + jX \\\ Y &= G + jB \end{align}}

where R is resistance, G is conductance, X is reactance, and B is susceptance. For ideal resistors, Z and Y reduce to R and G respectively. But for AC networks containing capacitors and inductors, X and B are nonzero.

Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle Z = 1/Y} for AC circuits, just as Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle R = 1/G} for DC circuits.

### Frequency dependence[edit | edit source]

A key feature of AC circuits is that the resistance and conductance can be frequency-dependent, a phenomenon known as the universal dielectric response.[8] One reason, mentioned above is the skin effect (and the related proximity effect). Another reason is that the resistivity itself may depend on frequency (see Drude model, deep-level traps, resonant frequency, Kramers–Kronig relations, etc.)

## Energy dissipation and Joule heating[edit | edit source]

Main article: Joule heating

File:Cartridge-heater-hot.jpg

Running current through a material with resistance creates heat, in a phenomenon called Joule heating. In this picture, a cartridge heater, warmed by Joule heating, is glowing red hot.

Resistors (and other elements with resistance) oppose the flow of electric current; therefore, electrical energy is required to push current through the resistance. This electrical energy is dissipated, heating the resistor in the process. This is called Joule heating (after James Prescott Joule), also called ohmic heating or resistive heating.

The dissipation of electrical energy is often undesired, particularly in the case of transmission losses in power lines. High voltage transmission helps reduce the losses by reducing the current for a given power.

On the other hand, Joule heating is sometimes useful, for example in electric stoves and other electric heaters (also called resistive heaters). As another example, incandescent lamps rely on Joule heating: the filament is heated to such a high temperature that it glows "white hot" with thermal radiation (also called incandescence).

The formula for Joule heating is: Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle P=I^2R} where P is the power (energy per unit time) converted from electrical energy to thermal energy, R is the resistance, and I is the current through the resistor.

## Dependence on other conditions[edit | edit source]

### Temperature dependence[edit | edit source]

Main article: Electrical resistivity and conductivity § Temperature dependence

Near room temperature, the resistivity of metals typically increases as temperature is increased, while the resistivity of semiconductors typically decreases as temperature is increased. The resistivity of insulators and electrolytes may increase or decrease depending on the system. For the detailed behavior and explanation, see Electrical resistivity and conductivity.

As a consequence, the resistance of wires, resistors, and other components often change with temperature. This effect may be undesired, causing an electronic circuit to malfunction at extreme temperatures. In some cases, however, the effect is put to good use. When temperature-dependent resistance of a component is used purposefully, the component is called a resistance thermometer or thermistor. (A resistance thermometer is made of metal, usually platinum, while a thermistor is made of ceramic or polymer.)

Resistance thermometers and thermistors are generally used in two ways. First, they can be used as thermometers: by measuring the resistance, the temperature of the environment can be inferred. Second, they can be used in conjunction with Joule heating (also called self-heating): if a large current is running through the resistor, the resistor's temperature rises and therefore its resistance changes. Therefore, these components can be used in a circuit-protection role similar to fuses, or for feedback in circuits, or for many other purposes. In general, self-heating can turn a resistor into a nonlinear and hysteretic circuit element. For more details see Thermistor#Self-heating effects.

If the temperature T does not vary too much, a linear approximation is typically used: Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle R(T) = R_0[1+\alpha (T - T_0)]} where Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \alpha} is called the temperature coefficient of resistance, Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle T_0} is a fixed reference temperature (usually room temperature), and Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle R_0} is the resistance at temperature Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle T_0} . The parameter Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \alpha} is an empirical parameter fitted from measurement data. Because the linear approximation is only an approximation, Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \alpha} is different for different reference temperatures. For this reason it is usual to specify the temperature that Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \alpha} was measured at with a suffix, such as Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \alpha_{15}} , and the relationship only holds in a range of temperatures around the reference.[9]

The temperature coefficient Failed to parse (SVG (MathML can be enabled via browser plugin): Invalid response ("Math extension cannot connect to Restbase.") from server "https://wikimedia.org/api/rest_v1/":): {\displaystyle \alpha} is typically +3×10−3 K−1 to +6×10−3 K−1 for metals near room temperature. It is usually negative for semiconductors and insulators, with highly variable magnitude.[e]

### Strain dependence[edit | edit source]

Main article: Strain gauge

Just as the resistance of a conductor depends upon temperature, the resistance of a conductor depends upon strain.[10] By placing a conductor under tension (a form of stress that leads to strain in the form of stretching of the conductor), the length of the section of conductor under tension increases and its cross-sectional area decreases. Both these effects contribute to increasing the resistance of the strained section of conductor. Under compression (strain in the opposite direction), the resistance of the strained section of conductor decreases. See the discussion on strain gauges for details about devices constructed to take advantage of this effect.

### Light illumination dependence[edit | edit source]

Main articles: Photoresistor and Photoconductivity

Some resistors, particularly those made from semiconductors, exhibit photoconductivity, meaning that their resistance changes when light is shining on them. Therefore, they are called photoresistors (or light dependent resistors). These are a common type of light detector.

## Superconductivity[edit | edit source]

Main article: Superconductivity

Superconductors are materials that have exactly zero resistance and infinite conductance, because they can have V = 0 and I ≠ 0. This also means there is no joule heating, or in other words no dissipation of electrical energy. Therefore, if superconductive wire is made into a closed loop, current flows around the loop forever. Superconductors require cooling to temperatures near 4 K with liquid helium for most metallic superconductors like niobium–tin alloys, or cooling to temperatures near 77 K with liquid nitrogen for the expensive, brittle and delicate ceramic high temperature superconductors. Nevertheless, there are many technological applications of superconductivity, including superconducting magnets.

## See also[edit | edit source]

* Conductance quantum
* Von Klitzing constant (its reciprocal)
* Electrical measurements
* Contact resistance
* Electrical resistivity and conductivity for more information about the physical mechanisms for conduction in materials.
* Johnson–Nyquist noise
* Quantum Hall effect, a standard for high-accuracy resistance measurements.
* Resistor
* RKM code
* Series and parallel circuits
* Sheet resistance
* SI electromagnetism units
* Thermal resistance
* Voltage divider
* Voltage drop

## Footnotes[edit | edit source]

1. ^ The resistivity of copper is about 1.7×10−8 Ω⋅m.[4]
2. ^ For a fresh Energizer E91 AA alkaline battery, the internal resistance varies from 0.9 Ω at −40 °C, to 0.1 Ω at +40 °C.[6]
3. ^ A 60 W light bulb (in the USA, with 120 V mains electricity) draws RMS current 60 W/120 V = 500 mA, so its resistance is 120 V/500 mA = 240 Ω. The resistance of a 60 W light bulb in Europe (230 V mains) is 900 Ω. The resistance of a filament is temperature-dependent; these values are for when the filament is already heated up and the light is already glowing.
4. ^ 100 kΩ for dry skin contact, 1 kΩ for wet or broken skin contact. High voltage breaks down the skin, lowering resistance to 500 Ω. Other factors and conditions are relevant as well. For more details, see the electric shock article, and NIOSH 98-131.[7]
5. ^ See Electrical resistivity and conductivity for a table. The temperature coefficient of resistivity is similar but not identical to the temperature coefficient of resistance. The small difference is due to thermal expansion changing the dimensions of the resistor.

## References[edit | edit source]

1. ^ a b Brown, Forbes T. (2006). Engineering System Dynamics: A Unified Graph-Centered Approach (2nd ed.). Boca Raton, Florida: CRC Press. p. 43\. ISBN 978-0-8493-9648-9.
2. ^ a b Kaiser, Kenneth L. (2004). Electromagnetic Compatibility Handbook. Boca Raton, Florida: CRC Press. pp. 13–52. ISBN 978-0-8493-2087-3.
3. ^ Fink & Beaty (1923). "Standard Handbook for Electrical Engineers". Nature (11th ed.). 111 (2788): 17–19. Bibcode:1923Natur.111..458R. doi:10.1038/111458a0. hdl:2027/mdp.39015065357108. S2CID 26358546.
4. ^ Cutnell, John D.; Johnson, Kenneth W. (1992). Physics (2nd ed.). New York: Wiley. p. 559\. ISBN 978-0-471-52919-4.
5. ^ McDonald, John D. (2016). Electric Power Substations Engineering (2nd ed.). Boca Raton, Florida: CRC Press. pp. 363ff. ISBN 978-1-4200-0731-2.
6. ^ Battery internal resistance (PDF) (Report). Energizer Corp.
7. ^ "Worker Deaths by Electrocution" (PDF). National Institute for Occupational Safety and Health. Publication No. 98-131. Retrieved 2 November 2014.
8. ^ Zhai, Chongpu; Gan, Yixiang; Hanaor, Dorian; Proust, Gwénaëlle (2018). "Stress-dependent electrical transport and its universal scaling in granular materials". Extreme Mechanics Letters. 22: 83–88. arXiv:1712.05938. doi:10.1016/j.eml.2018.05.005. S2CID 51912472.
9. ^ Ward, M.R. (1971). Electrical Engineering Science. McGraw-Hill. pp. 36–40.
10. ^ Meyer, Sebastian; et al. (2022), "Characterization of the deformation state of magnesium by electrical resistance", Volume 215, Scripta Materialia, vol. 215, p. 114712, doi:10.1016/j.scriptamat.2022.114712, S2CID 247959452

## External links[edit | edit source]

Wikimedia Commons has media related to Electrical resistance and conductance.

* "Resistance calculator". Vehicular Electronics Laboratory. Clemson University. Archived from the original on 11 July 2010.
* "Electron conductance models using maximal entropy random walks". wolfram.com. Wolfram Demonstrantions Project.

*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template