Design for manufacturability

Designing products to facilitate manufacturing

This article may require cleanup to meet Wikipedia's quality standards. No cleanup reason has been specified. Please help improve this article if you can. (January 2011) (Learn how and when to remove this template message)

|

Redesigned for manufacturability

Design for manufacturability (also sometimes known as design for manufacturing or DFM) is the general engineering practice of designing products in such a way that they are easy to manufacture. The concept exists in almost all engineering disciplines, but the implementation differs widely depending on the manufacturing technology. DFM describes the process of designing or engineering a product in order to facilitate the manufacturing process in order to reduce its manufacturing costs. DFM will allow potential problems to be fixed in the design phase which is the least expensive place to address them. Other factors may affect the manufacturability such as the type of raw material, the form of the raw material, dimensional tolerances, and secondary processing such as finishing.

Depending on various types of manufacturing processes there are set guidelines for DFM practices. These DFM guidelines help to precisely define various tolerances, rules and common manufacturing checks related to DFM.

While DFM is applicable to the design process, a similar concept called DFSS (design for Six Sigma) is also practiced in many organizations.

## For printed circuit boards (PCB)[edit]

In the PCB design process, DFM leads to a set of design guidelines that attempt to ensure manufacturability. By doing so, probable production problems may be addressed during the design stage.

Ideally, DFM guidelines take into account the processes and capabilities of the manufacturing industry. Therefore, DFM is constantly evolving.

As manufacturing companies evolve and automate more and more stages of the processes, these processes tend to become cheaper. DFM is usually used to reduce these costs.[1] For example, if a process may be done automatically by machines (i.e. SMT component placement and soldering), such process is likely to be cheaper than doing so by hand.

## For integrated circuits (IC)[edit]

Achieving high-yielding designs, in the state of the art VLSI technology has become an extremely challenging task due to the miniaturization as well as the complexity of leading-edge products. Here, the DFM methodology includes a set of techniques to modify the design of integrated circuits (IC) in order to make them more manufacturable, i.e., to improve their functional yield, parametric yield, or their reliability.

### Background[edit]

Traditionally, in the pre-nanometer era, DFM consisted of a set of different methodologies trying to enforce some soft (recommended) design rules regarding the shapes and polygons of the physical layout of an integrated circuit. These DFM methodologies worked primarily at the full chip level. Additionally, worst-case simulations at different levels of abstraction were applied to minimize the impact of process variations on performance and other types of parametric yield loss. All these different types of worst-case simulations were essentially based on a base set of worst-case (or corner) SPICE device parameter files that were intended to represent the variability of transistor performance over the full range of variation in a fabrication process. Additionally, SPICE models should have mismatches built into them for analog circuit simulations. Many mismatches are size and orientation dependent, which can be well modeled. Always "copy exactly" when doing analog layouts as many mismatches are not well understood or controlled (i.e. if one device has North to South current flow, all matched devices should have North to South current flow).

### Taxonomy of yield loss mechanisms[edit]

The most important yield loss models (YLMs) for VLSI ICs can be classified into several categories based on their nature.

* Functional yield loss is still the dominant factor and is caused by mechanisms such as misprocessing (e.g., equipment-related problems), systematic effects such as printability or planarization problems, and purely random defects.
* High-performance products may exhibit parametric design marginalities caused by either process fluctuations or environmental factors (such as supply voltage or temperature).
* The test-related yield losses, which are caused by incorrect testing, can also play a significant role.

### Techniques[edit]

After understanding the causes of yield loss, the next step is to make the design as resistant as possible. Techniques used for this include:

* Substituting higher yield cells where permitted by timing, power, and routability.
* Changing the spacing and width of the interconnect wires, where possible
* Optimizing the amount of redundancy in internal memories.
* Substituting fault tolerant (redundant) vias in a design where possible

All of these require a detailed understanding of yield loss mechanisms, since these changes trade off against one another. For example, introducing redundant vias will reduce the chance of via problems, but increase the chance of unwanted shorts. Whether this is good idea, therefore, depends on the details of the yield loss models and the characteristics of the particular design.

## For CNC machining[edit]

### Objective[edit]

The objective is to design for lower cost. The cost is driven by time, so the design must minimize the time required to not just machine (remove the material), but also the set-up time of the CNC machine, NC programming, fixturing and many other activities that are dependent on the complexity and size of the part.

### Set-Up time of operations (flip of the part)[edit]

Unless a 4th and/or 5th axis is used, a CNC can only approach the part from a single direction. One side must be machined at a time (called an operation or op). Then the part must be flipped from side to side to machine all of the features. The geometry of the features dictates whether the part must be flipped over or not. The more ops (flip of the part), the more expensive the part because it incurs substantial set-up and load/unload time.

Each operation (flip of the part) has set-up time, machine time, time to load/unload tools, time to load/unload parts, and time to create the NC program for each operation. If a part has only 1 operation, then parts only have to be loaded/unloaded once. If it has 5 operations, then load/unload time is significant.

The low hanging fruit is minimizing the number of operations (flip of the part) to create significant savings. For example, it may take only 2 minutes to machine the face of a small part, but it will take an hour to set the machine up to do it. Or, if there are 5 operations at 1.5 hours each, but only 30 minutes total machine time, then 7.5 hours is charged for just 30 minutes of machining.[2]

Lastly, the volume (number of parts to machine) plays a critical role in amortizing the set-up time, programming time and other activities into the cost of the part. In the example above, the part in quantities of 10 could cost 7–10 times the cost in quantities of 100.

Typically, the law of diminishing returns presents itself at volumes of 100–300 because set-up times, custom tooling and fixturing can be amortized into the noise.[3]

### Material type[edit]

The most easily machined types of metals include aluminum, brass, and softer metals. As materials get harder, denser and stronger, such as steel, stainless steel, titanium, and exotic alloys, they become much harder to machine and take much longer, thus being less manufacturable. Most types of plastic are easy to machine, although additions of fiberglass or carbon fiber can reduce the machinability. Plastics that are particularly soft and gummy may have machinability problems of their own.

### Material form[edit]

Metals come in all forms. In the case of aluminum as an example, bar stock and plate are the two most common forms from which machined parts are made. The size and shape of the component may determine which form of material must be used. It is common for engineering drawings to specify one form over the other. Bar stock is generally close to 1/2 of the cost of plate on a per pound basis. So although the material form isn't directly related to the geometry of the component, cost can be removed at the design stage by specifying the least expensive form of the material.

### Tolerances[edit]

A significant contributing factor to the cost of a machined component is the geometric tolerance to which the features must be made. The tighter the tolerance required, the more expensive the component will be to machine. When designing, specify the loosest tolerance that will serve the function of the component. Tolerances must be specified on a feature by feature basis. There are creative ways to engineer components with lower tolerances that still perform as well as ones with higher tolerances.

### Design and shape[edit]

As machining is a subtractive process, the time to remove the material is a major factor in determining the machining cost. The volume and shape of the material to be removed as well as how fast the tools can be fed will determine the machining time. When using milling cutters, the strength and stiffness of the tool which is determined in part by the length to diameter ratio of the tool will play the largest role in determining that speed. The shorter the tool is relative to its diameter the faster it can be fed through the material. A ratio of 3:1 (L:D) or under is optimum.[4] If that ratio cannot be achieved, a solution like this depicted here can be used.[5] For holes, the length to diameter ratio of the tools are less critical, but should still be kept under 10:1.

There are many other types of features which are more or less expensive to machine. Generally chamfers cost less to machine than radii on outer horizontal edges. 3D interpolation is used to create radii on edges that are not on the same plane which incur 10X the cost.[6] Undercuts are more expensive to machine. Features that require smaller tools, regardless of L:D ratio, are more expensive.

## Design for inspection[edit]

The concept of design for inspection (DFI) should complement and work in collaboration with design for manufacturability (DFM) and design for assembly (DFA) to reduce product manufacturing cost and increase manufacturing practicality. There are instances when this method could cause calendar delays since it consumes many hours of additional work such as the case of the need to prepare for design review presentations and documents. To address this, it is proposed that instead of periodic inspections, organizations could adopt the framework of empowerment, particularly at the stage of product development, wherein the senior management empowers the project leader to evaluate manufacturing processes and outcomes against expectations on product performance, cost, quality and development time.[7] Experts, however, cite the necessity for the DFI because it is crucial in performance and quality control, determining key factors such as product reliability, safety, and life cycles.[8] For an aerospace components company, where inspection is mandatory, there is the requirement for the suitability of the manufacturing process for inspection. Here, a mechanism is adopted such as an inspectability index, which evaluates design proposals.[9] Another example of DFI is the concept of cumulative count of conforming chart (CCC chart), which is applied in inspection and maintenance planning for systems where different types of inspection and maintenance are available.[10]

## Design for additive manufacturing[edit]

Main article: Design for additive manufacturing

Additive manufacturing broadens the ability of a designer to optimize the design of a product or part (to save materials for example). Designs tailored for additive manufacturing are sometimes very different from designs tailored for machining or forming manufacturing operations.

In addition, due to some size constraints of additive manufacturing machines, sometimes the related bigger designs are split into smaller sections with self-assembly features or fasteners locators.

A common characteristic of additive manufacturing methods, such as fused deposition modeling, is the need for temporary support structures for overhanging part features. Post-processing removal of these temporary support structures increases the overall cost of fabrication. Parts can be designed for additive manufacturing by eliminating or reducing the need for temporary support structures. This can be done by limiting the angle of overhanging structures to less than the limit of the given additive manufacturing machine, material, and process (for example, less than 70 degrees from vertical).

## See also[edit]

* Design for X
* Electronic design automation
* Reliability engineering
* Six Sigma
* Statistical process control
* DFMA

## References[edit]

1. ^ Dolcemascolo, Darren. "DFM helps manufacturers reduce cost while maintaining value". Reliable Plant.
2. ^ "How to Design Cheap Machined Parts and Why? - Parametric Manufacturing". 3 September 2016.
3. ^ "Guide to CNC Machining Prototype & Production - Parametric Manufacturing". August 2016.
4. ^ Inc., eFunda. "Milling: Design Rules". `{{cite web}}`: `|last=` has generic name (help)
5. ^ "Design Guide" (PDF). Pro CNC. Retrieved January 30, 2017.
6. ^ "The #1 Killer to a Low Price CNC Machined Part - Parametric Manufacturing - CNC Machine Shop + Wire EDM". 17 July 2016.
7. ^ Anderson, David (2004). Design for Manufacturability & Concurrent Engineering: How to Design for Low Cost, Design in High Quality, Design for Lean Manufacture, and Design Quickly for Fast Production. Cambria, CA: CIM Press. p. 28\. ISBN 978-1878072238.
8. ^ Gupta, Praveen (2006). Six Sigma Business Scorecard, Chapter 3 - Need for the Six Sigma Business Scorecard. New York: McGraw Hill Professional. p. 4\. ISBN 9780071735117.
9. ^ Stolt, Roland; Elgh, Frederik; Andersson, Petter (2017). "Design for Inspection - Evaluating the Inspectability of Aerospace Components in the Early Stages of Design". Procedia Manufacturing. 11: 1193–1199. doi:10.1016/j.promfg.2017.07.244 - via Elsevier Science Direct.
10. ^ Chan, Ling-Yau; Wu, Shaomin (October 1, 2009). "Optimal design for inspection and maintenance policy based on the CCC chart". Computers & Industrial Engineering. 57 (3): 667–676. doi:10.1016/j.cie.2008.12.009. hdl:1826/4041. ISSN 0360-8352. S2CID 206721473.

## Sources[edit]

* Mentor Graphics - DFM: What is it and what will it do? (must fill request form).
* Mentor Graphics - DFM: Magic Bullet or Marketing Hype (must fill request form).
* Electronic Design Automation For Integrated Circuits Handbook, by Lavagno, Martin, and Scheffer, ISBN 0-8493-3096-3 A survey of the field of EDA. The above summary was derived, with permission, from Volume II, Chapter 19, Design for Manufacturability in the Nanometer Era, by Nicola Dragone, Carlo Guardiani, and Andrzej J. Strojwas.
* Design for Manufacturability And Statistical Design: A Constructive Approach, by Michael Orshansky, Sani Nassif, Duane Boning ISBN 0-387-30928-4
* Estimating Space ASICs Using SEER-IC/H, by Robert Cisneros, Tecolote Research, Inc. (2008) Complete Presentation Archived 2012-02-20 at the Wayback Machine

## External links[edit]

Wikibooks has a book on the topic of: Practical Electronics/PCB Layout

* Why DFM/DFMA is Business Critical
* Design for manufacturing checklist – DFM,DFA(Design for assembly checklist from Quick-teck PCB manufacturer
* Arc Design for Manufacturability Tips
* Design for Manufacturing and Assembly
* Turning designs into reality: The Manufacturability paradigm

* v
* t
* e

Design

* Outline
* Designer

Disciplines

| Communication
design|

* Advertising
* Book design
* Brand design
* Exhibit design
* Film title design
* Graphic design
* Motion
* Postage stamp design
* Print design
* Illustration
* Information design
* Instructional design
* News design
* Photography
* Retail design
* Signage / Traffic sign design
* Typography / Type design
* Video design
* Visual merchandising

|

Environmental
design|

* Architecture
* Architectural lighting design
* Building design
* Passive solar
* Ecological design
* Environmental impact design
* Garden design
* Computer-aided
* Healthy community design
* Hotel design
* Interior architecture
* Interior design
* EID
* Keyline design
* Landscape architecture
* Sustainable
* Landscape design
* Spatial design
* Urban design

Industrial
design|

* Automotive design
* Automotive suspension design
* CMF design
* Corrugated box design
* Electric guitar design
* Furniture design
* Sustainable
* Hardware interface design
* Motorcycle design
* Packaging and labeling
* Photographic lens design
* Product design
* Production design
* Sensory design
* Service design

Interaction
design|

* Experience design
* EED
* Game design
* Level design
* Video game design
* Hardware interface design
* Icon design
* Immersive design
* Information design
* Sonic interaction design
* User experience design
* User interface design
* Web design

Other
applied arts|

* Public art design
* Ceramic / glass design
* Fashion design
* Costume design
* Jewellery design
* Floral design
* Game art design
* Property design
* Scenic design
* Sound design
* Stage/set lighting design
* Textile design

Other
design
& engineering|

* Algorithm design
* Behavioural design
* Boiler design
* Database design
* Drug design
* Electrical system design
* Experimental design
* Filter design
* Geometric design
* Work design
* Integrated circuit design
* Circuit design
* Physical design
* Power network design
* Mechanism design
* Nuclear weapon design
* Nucleic acid design
* Organization design
* Process design
* Processor design
* Protein design
* Research design
* Social design
* Software design
* Spacecraft design
* Strategic design
* Systems design

Approaches

* Activity-centered
* Adaptive web
* Affective
* Brainstorming
* By committee
* By contract
* C-K theory
* Closure
* Co-design
* Concept-oriented
* Configuration
* Contextual
* Continuous
* Cradle-to-cradle
* Creative problem-solving
* Creativity techniques
* Critical
* Design fiction
* Defensive
* Design–bid–build
* Design–build
* architect-led
* Diffuse
* Domain-driven
* Ecological design
* Energy neutral
* Engineering design process
* Probabilistic design
* Error-tolerant
* Fault-tolerant
* Framework-oriented
* For assembly
* For behaviour change
* For manufacturability
* For Six Sigma
* For testing
* For X
* Functional
* Generative
* Geodesign
* HCD
* High-level
* Inclusive
* Integrated
* Integrated topside
* Intelligence-based
* Iterative
* KISS principle
* Low-level
* Metadesign
* Mind mapping
* Modular
* New Wave
* Object-oriented
* Open
* Parametric
* Participatory
* Platform-based
* Policy-based
* Process-centered
* Public interest
* Rational
* Regenerative
* Reliability engineering
* Research-based
* Responsibility-driven
* RWD
* Safe-life
* Sustainable
* Systemic
* SOD
* Tableless web
* Theory of constraints
* Top-down and bottom-up
* Transformation
* Transgenerational
* TRIZ
* Universal
* Design for All
* Usage-centered
* Use-centered
* User-centered
* Empathic
* User innovation
* Value-driven
* Value sensitive
* Privacy by

* Design choice
* computing
* controls
* culture
* flow
* leadership
* management
* marker
* methods
* pattern
* research
* science
* sprint
* strategy
* theory
* thinking

* Tools
* Intellectual property
* Organizations
* Awards

| Tools|

* AAD
* Architectural model
* Blueprint
* Comprehensive layout
* CAD
* CAID
* Virtual home design software
* CAutoD
* Design quality indicator
* Electronic design automation
* Flowchart
* Mockup
* Design specification
* Prototype
* Sketch
* Storyboard
* Technical drawing
* HTML editor
* Website wireframe

|

Intellectual
property|

* Community design
* Design around
* Design infringement
* Design patent
* Fashion design copyright
* Geschmacksmuster
* Industrial design rights
* European Union

Organizations|

* American Institute of Graphic Arts
* Chartered Society of Designers
* Design and Industries Association
* Design Council
* International Forum Design
* Design Research Society

Awards|

* European Design Award
* German Design Award
* Good Design Award (Museum of Modern Art)
* Good Design Award (Chicago Athenaeum)
* Graphex
* IF Product Design Award
* James Dyson Award
* Prince Philip Designers Prize

Related topics

* Agile
* Concept art
* Conceptual design
* Creative industries
* Cultural icon
* .design
* Enterprise architecture
* Form factor
* Futures studies
* Indie design
* Innovation management
* Intelligent design
* Lean startup
* New product development
* OODA loop
* Philosophy of design
* Process simulation
* Slow design
* STEAM fields
* Unintelligent design
* Visualization
* Wicked problem

* Design brief
* change
* classic
* competition
* architectural
* student
* director
* education
* elements
* engineer
* firm
* history
* knowledge
* language
* life
* load
* museum
* paradigm
* principles
* rationale
* review
* specification
* studies
* studio
* technology

* Commons
* Wikibooks
* Wikinews
* Wikiquote
* Wikisource
* Wiktionary

*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template