Inline skates

Boots with wheels arranged in a single line

Recreational skates Urban skates

Inline skates are boots with wheels arranged in a single line from front to back, allowing one to move in an ice skate-like fashion. Inline skates are technically a type of roller skate, but most people associate the term roller skates with quad skates, another type of roller skate with a two-by-two wheel arrangement similar to a car. Quad skates were popularized in the late 19th and early 20th centuries. Inline skates became prominent in the late 1980s with the rise of Rollerblade, Inc., and peaked in the late 1990s. The registered trademark Rollerblade has since become a generic trademark due to its popularity. To this day, "rollerblades" continues to be used in everyday language to refer to inline skates, along with the accompanying verb "rollerblading" describing their use.

In the 21st century, inline skates come in many varieties, suitable for different types of inline skating activities and sports such as recreational skating, urban skating, roller hockey, street hockey, speed skating, slalom skating, aggressive skating, vert skating, and artistic inline skating. Inline skaters can be found at traditional roller rinks, street hockey rinks, skateparks, and on urban streets. In cities around the world, skaters organize urban group skates. Paris Friday Night Fever Skate (Randonnée du Vendredi Soir) is renowned for its large crowd size, as well as its iconic +10 mile urban routes.[1][2] Wednesday Night Skate NYC is its equivalent in New York City, also run by volunteers, albeit smaller in size.[3][4]

## History

[edit]

Main article: History of inline skates

The documented history of inline skates dates back to the early 18th century, when enterprising inventors sought to make boots roll on wheels to emulate the gliding of ice blades on dry land. Because these wheeled skates were modeled after ice blades, their wheels were arranged in a single line. Skates were simply assumed to have a single runner, whether it was a steel blade on an ice skate or a row of wheels on a wheeled skate.[5]

### Wheeled skates

[edit]

First patented wheeled skate - 1819

The first patented wheeled skate was filed in France in 1819 by Charles-Louis Petibled.[6] From that point forward, more patents and documented designs continued to explore wheeled alternatives to ice skates.[7] Around 1960, wheeled skates began to gain popularity, and new patents appeared under names such as roller-skates and parlor skates. As inventions increased, roller skates began to diverge from the original single-line layout.[8] Inventors experimented with two rows of wheels as a learning platform for beginner skaters.[9] These double-row skates offered greater stability, but they were difficult to turn.[10]

### Roller skates

[edit]

Plimpton prototype 1863-1866

In 1863, James Plimpton invented a roller skate with four wheels arranged in a two-by-two configuration, similar to a wagon, and added a clever mechanism for turning.[11] It was the first double-row skate that allowed beginners to steer easily by simply leaning in the desired direction.[12] Plimpton's invention sparked a rapid rise in roller skate popularity and spread across both sides of the Atlantic, creating a period of "rinkomania" during the 1860s and 1870s.[13] His design also redefined the term roller skate, which no longer referred to all wheeled skates but became synonymous with the two-by-two Plimpton style.[A]

### After Plimpton

[edit]

Racing Roller Skates - 1904

The development of precision ball bearings in the mid-19th century helped make bicycles more efficient and practical.[15] By the 1880s, Plimpton-style roller skates similarly incorporated ball bearings into their wheel assemblies, making skates roll more efficiently.[16] At the same time, manufacturers began operating skating rinks as promotional ventures from the 1880s through the 1910s. All of these further fueled the Plimpton skate craze.[7]: 19–20, 25

Although Plimpton's roller skates took center stage, inventors and enterprises continued to introduce new roller skates with a single line of wheels between the 1870s and the 1910s.[17] These models included features such as brakes, pneumatic tires, and foot stands placed below the center of the wheels.

### Precursors

[edit]

Chicago Roller-Blade - 1965

From the 1910s through the 1970s, many new variations of single-line wheeled skates were patented and manufactured.[18] While still in the shadow of 2x2 roller skates, some models began to gain popularity among ice hockey players by the 1960s and 1970s, due to their better emulation of ice blades. In particular, off-season training skates used by USSR speed skaters inspired Gordon Ware of the Chicago Roller Skate Company to develop and patent a wheeled skate,[19] which was sold through Montgomery Ward in 1965 under the name "Roller-Blade".[20][B] In 1973, Ralph Backstrom promoted the Super Sport Skate,[21] a joint venture with his friend Maury Silver, as an off-season training tool for hockey players.[22][C] Both of these skate models became direct precursors to modern inline skates.

CCM Tacks boot riveted to Super Street Skate ca. 1980

In a related development, the ski boot manufacturer Lange introduced the first molded plastic ski boots with internal liners in the 1960s.[24] In the 1970s, Lange entered the ice hockey market with similar hard plastic boots featuring hinged cuffs and achieved some success.[25] Meanwhile, skateboarding reached new heights during the 1970s, thanks to the introduction of polyurethane wheels and their superior performance.[26] The confluence of molded plastic boots with hinged cuffs, polyurethane wheels, Super Sport Skates, and the earlier Chicago Roller-Blade laid the foundation for the emergence of Rollerblade in the 1980s and its widespread appeal among the general public.[27]: 12–16 [20]

### Modern inline skates

[edit]

Lightning TRS from Rollerblade - 1988 Urban inline skates - 2024

In 1979, Scott Olson, a hockey player from Minneapolis, discovered the Super Sport Skate. He began selling them to local hockey players as a licensed distributor and soon started modifying them.[28] Olson, his brothers, and his friends replaced the stock boots with customers' old hockey boots and swapped out the original wheels for polyurethane ones.[29] Through further tinkering, prototyping and road testing everywhere he could, Olson eventually arrived at a skate design with an adjustable/expandable frame, polyurethane wheels and double ball bearings.[30] The skate rolled faster, and remained more reliable on road surfaces. However, a patent search revealed that the Chicago Roller-Blade already covered many of these features. In 1981, Olson persuaded the Chicago Roller Skate Company to transfer the patent to him in exchange for a share of future profits.[31]

Thus began the modern history of inline skates, with Olson's company eventually becoming known as Rollerblade, Inc. by around 1988.[32] The registered trademark "Rollerblade" became so well-known that it entered common usage as a generic term.[33][34] Around this time, the company began promoting the term in-line skating in an effort to prevent "rollerblading" from becoming a verb.[35] The campaign proved effective, as media outlets, newspapers, and competitors adopted "in-line skating" as the preferred term by 1990.[36] The phrase was soon shortened to inline, the name by which these skates are known today.

Modern inline skates became practical for mass production and appealing as a recreational activity once key technologies came together. These included polyurethane wheels, ISO 608 standard ball bearings, and molded plastic boots. These skates incorporate double ball bearings with dual-purpose axles from Chomin Harry (1925), single-piece frames from Christian Siffert (1938), adjustable wheel rockering from Gordon Ware (1966), single-unit boot/frame, longer frames and larger wheels from Maury Silver (1975), plus additional innovations.

## Design and function

[edit]

### Components

[edit]

Boot, frame, wheels, bearings, axles and tool

All modern inline skates share a common basic blueprint. A skate comprises a boot, worn on the foot. To the bottom of the boot is attached a frame, the most rigid part of the skate. The frame holds a number of wheels in place with wheel axles. In between a wheel and an axle are two bearings. Bearings allow a wheel to rotate freely around its axle. Finally, a rubber brake typically attaches to the frame of the right boot, on recreational skates.[27]: 17–27 [37]: 14–39 [38]: 41–51

For many skaters, the frame is never removed or replaced. But wheels are consumables, as they wear down with use, and require periodic mounting rotations and even replacements.[33]: 81–86  Inline skates usually come with a skate tool for wheel, bearing and frame maintenance. The tool will have a hex wrench or a Torx wrench for removing wheel axles from a frame, and wherever applicable, for removing bearings from a wheel, and for removing a frame from a boot.[39][27]: 39–45 [37]: 39–51

Securing the foot

Hard boot

Soft boot

Hybrid boot

In the 1980s and 1990s, all inline skates had hard boots, borrowed from ski boot designs. A removable liner in a hard boot provides a snug yet comfortable fit between a skater's foot and the hard shell. Around 1996, K2 introduced soft boots with an exoskeleton. These provide the most comfortable fit, at the expense of reduced rigidity. In the 2010s, hybrid (soft) boots with an endoskeleton were introduced to the high-end market. A hybrid boot has an integrated, non-removable liner. This is glued to a rigid endoskeleton shell integrated with the sole, providing direct power transfer from the foot to the wheels.[40]: 142 [41][42]

All three types are able to secure a foot in them without slack, with proper closure systems. Soft boots are often laced, and hard shells are usually secured with buckles. Velcro straps are also common in all types of boots. Well-designed boots provide proper heel support and ankle support to a skater.[37]: 14–39 [38]: 47–52 [40]: 142

Trade-offs

The length of a frame positively affects stability and negatively affects turning agility. Longer frames accommodate more wheels, and taller frames larger wheels; both positively affect top skating speed. Modern inline skates are equipped with polyurethane wheels. Softer wheels provide a better grip on smooth indoor surfaces, while harder wheels wear down less on rough outdoor surfaces. Beginners skate with all wheels touching the ground, for enhanced stability, known as a "flat" wheel setup. Advanced skaters may choose to configure wheels in a "rockered" setup for enhanced maneuverability. The weight of a skate is an important consideration for some disciplines. Lighter boots, frames, and wheels are preferred. However, weight reduction is only achieved with escalating costs and diminishing returns.[37]: 14–39 [43]: 19–33

### Striding and gliding

[edit]

Striding

Gliding

Recreational inline skating involves a continuous interplay between striding and gliding. As one foot pushes laterally against the ground during the striding phase, it converts sideways force into forward momentum. Meanwhile, the opposite foot glides ahead, supporting the skater’s weight. These phases overlap fluidly, with each skate alternating between pushing and gliding in a coordinated rhythm that sustains forward motion.[44][38]: 57–75

These two movements place distinct and often conflicting demands on skate design. A powerful stride benefits from a large contact area between the wheels and the ground, maximizing friction for a more forceful push-off. In contrast, a smooth and sustained glide calls for minimal contact to reduce friction and rolling resistance. Much of inline skate design involves balancing these opposing requirements to achieve both propulsion and efficiency.[45][46]

### Edging and turning

[edit]

Edging for fast turns Three edging angles

Modern inline skate design was heavily influenced by ice hockey. Early inline skates from the 1980s aimed to replicate the feel of hockey skate blades, often using a rockered wheel setup to allow easier turning and quick directional changes. While slalom skaters relied on these rockered setups and hockey players made rapid turns using crossover maneuvers, recreational skaters soon realized that even a flat wheel setup could support effective turning, thanks to the grip provided by polyurethane wheels on pavement. As with ice skating, inline skaters could shift their body weight and apply pressure to one side of the skate to gradually turn while gliding.[33]: 81–86 [44][45][46]

This technique is known as edging, which involves tilting the skate to roll on one side of the wheels. Skaters use both sides of the wheels for different maneuvers. The inside edge refers to the side of the wheel facing the skater’s body, while the outside edge faces away. Edging is essential not only for turning but also for powerful stride pushes, which require a strong edge angle. Deep edging, however, requires proper support from the boot, frame, and wheels to prevent the foot from wobbling within the boot and to keep the wheels from sliding out from under the skater.[D][37]: 37–38 [43]: 19–24 [38]: 47–52 [37]: 19–20

### Heel support

[edit]

Heel support refers to the ability of a boot to keep a skater's heel comfortably seated and firmly locked down in the heel pocket of the boot, even during aggressive maneuvering.

A contoured heel pocket and a proper closure system work together to lock in the heel

A heel pocket is formed by the shell, inner liner and sole of a boot. A properly designed boot has a heel pocket that hugs the heel, with an anatomical contour. A proper closure system causes the "facing" (where eyelet tabs are) to push the instep against the heel pocket, preventing the foot from shifting or lifting during maneuvers. As a result, the heel remains in contact with the footbed at all times.[37]: 15–18

### Heel lock

[edit]

Proper heel lock serves as a stable foundation for the entire foot. It allows a skater to adopt an athletic stance for skating by flexing the lower leg forward, without raising the heel. A snug fit means reduced movement of the foot within the skate, and thus reduced opportunity for friction to cause blisters. At the same time, the whole skate becomes transfixed to the foot as an extension of it, allowing efficient strides with a faithful transfer of power from the foot to the ground.[47]: 35–36, 79–80

### Ankle support

[edit]

Rigid carbon-fiber quarter panels of this hockey boot prevents sideway wobbles of the foot while allowing the shin to flex forward

Ankle support refers to the ability of a boot to prevent sideways movement of a skater's ankle and lower leg, while allowing the shin to flex forward into an athletic stance. In some skates, such as recreational and aggressive skates, this is achieved via a hinged cuff. In other skates, such as hockey skates, this is enabled by rigid, and anatomically shaped quarter panels that lock both ankle bones in place, from two sides, leaving the shin to freely pivot forward.[37]: 5, 15–18 [48][40]: 142 [49]

Proper ankle support allows a skater to keep a skate upright as a straight extension of their entire leg, when observed from the front. Without rigid support on both sides of the ankle, the foot may wobble within the boot, causing the skate to tilt inward or outward. This creates pronation, making it harder for a skater to glide on a single skate at best, and resulting in sprains and other injuries at worst.[50]

### Forward flex

[edit]

Dorsiflexion (left) vs leg extended straight (right)

A properly designed boot does not hinder the mobility of the ankle joint, allowing a skater to pivot the lower leg (the shin) forward, adopting a squatting (athletic) stance. This forward flex (or forward leaning) is known as dorsiflexion of the foot. It places the center of body mass atop the ball of the foot, a balancing skill crucial to most skating moves. Without such a squatting stance, the leg and the skate form a 90° angle, placing the entire body weight of a skater on the rear wheel of the skate. This is dangerous for a beginner because a small backward shift of the upper body will cause a skater to pivot their entire body on the rear wheel, and thus fall uncontrollably backward.[37]: 67–77 [38]: 57–59 [44]

## Types

[edit]

Main article: Types of inline skates

Inline hockey in Sweden

There are a variety of ways to design and make modern inline skates. Different types of inline skates reflect needs specific to different inline skating disciplines, such as recreational skating, urban skating, roller hockey, street hockey, speed skating, slalom skating, aggressive skating, and artistic inline skating.

Manufacturers and resellers generally classify inline skates based on disciplines, such as aggressive skates, speed skates and hockey skates.[37]: 30–38  Some disciplines are not large enough to warrant their own classification. Thus, dissimilar disciplines with similar equipment needs are grouped under a single skate category. For instance, freestyle skating, slalom skating, wizard skating, city commuting, and urban skating may be crammed into a single "urban skates" category.[51] Then, there are the rest of skaters who casually skate, skate for fitness, or skate for cross-training. These purposes constitute 90% of actual inline skate sales. Skates suitable for these activities are often grouped together as "recreational skates".[41]

### Recreational

[edit]

Recreational skates

Fitness skates

Main article: Types of inline skates § Recreational

Some makers refer to recreational skates as "fitness skates". Others split them into two or more categories: recreational, fitness, and cross-training. Usually, the fitness and cross-training categories reflect increasing cost and thus quality of skates.[E] Soft boots with an exoskeleton are usually the least expensive. Hard boots with removable liners are often priced higher. Hybrid boots with an endoskeleton are high-end models.[48][42]

This category can be better understood as "unspecialized" inline skates, or generic skates. All other types of skates can be thought of as specialized deviations from this basic type.[41] Recreational skates usually come with four wheels of average size, and a frame of average length, which is just slightly longer than the boot. This places the front wheel halfway ahead of the toe box, and the rear wheel halfway behind the heel pocket, a design that remained unchanged since Scott Olson's adoption of Super Sport Skate from 1979.[21] Recreational skates are equipped with heel brakes. These allow beginners to learn to stop rolling, with a simple pivot of a foot on its heel.[27]: 25–26, 44–45, 52–57

### Aggressive

[edit]

Main article: Types of inline skates § Aggressive

Aggressive skates

Aggressive skates are the most specialized inline skates, in contrast to recreational skates. They are designed for one specific purpose only: grinds. Grinding is the art of sliding on street obstacles such as stairs, rails, benches, curbs, ramps and walls.[40]: 134–163  To support these stunts, aggressive skates are generally built with strong hard boots based on ski boots and bolted to thick frames which are fitted with the smallest wheels in all of inline skating.[52] To help a skater lock onto an obstacle of interest during a grind, an aggressive skate provides channels and surfaces such as H-blocks, frame grooves, backslide grooves, grind plates, soulplates, etc.[53] Transitioning between these stunts, a skater often jumps considerable heights, or rides down a long flight of stairs (known as stair bashing).[37]: 33, 156–168  Thus, aggressive boots are often fitted with shock absorbers to dampen shocks upon landing.

Park skating competition

Rollerblade Lightning TRS has been widely credited for enabling aggressive inline skating as a sport, with its durable boot and nylon-reinforced frame.[54] Aggressive skates co-evolved with the discipline which started as inline stunts.[47]: 98–110  It then turned into streetstyle skating, and finally into aggressive inline skating. The word "street" in street-style meant that skaters performed tricks on and over street obstacles, following nomenclature from skateboarding.[27]: 6, 64–77, 170–174  Skaters grind on street obstacles (termed street skating), perform stunts at skateparks (termed park skating), and take to the air at the top of ramps (termed vert skating).[37]: 33, 156–168

Frame groove and thick frame walls

Aggressive skates have standardized on UFS, the Universal Frame System. Most UFS frames accommodate small wheels up to 60 mm.[55] Some UFS frames with frame grooves and H-blocks are designed with thick walls to prevent wheel bites. allowing them to be used with a flat wheel setup.[53] Other UFS frames without prevention measures against wheel bites can be set up with an anti-rocker wheel configuration, with even smaller and harder "grindwheels" (or "antirockers") in the middle.[56] Some skaters go one step further, replacing the two middle wheels with non-rotating "juice blocks".[57]

The name "aggressive" has been controversial.[58] Many in the community call aggressive skating rollerblading (or simply blading), and thus members bladers.[41] Others call it aggro.[40]: 134–163 [F] Some skate manufacturers eschew the label "aggressive", choosing to market their aggressive skates instead as street skates or park skates.[59]: 40–41 [G]

### Hockey

[edit]

Main article: Types of inline skates § Hockey

Bauer hockey skate

In the 21st century, the boots used for inline hockey skates (roller hockey skates) are constructed using a process that differs significantly from those of other inline skates.[60] They are primarily produced by ice hockey manufacturers such as CCM, Bauer (Mission), True, and Marsblade.[37]: 37–38 [H] In many cases, the same boot is used across both sports, with either a blade holder for ice hockey or an inline frame for roller hockey.[I][J] As a result, inline hockey skates continue to rely on the rivet-based mounting system used in ice hockey, even though replaceable frame standards have become common in other skate categories.[55]

Hockey boot construction

Hockey skates feature some of the shortest frames among all inline skates, enabling players to make tight turns and perform crossovers without interference. Hockey boots are designed to sit as low to the ground as possible, limiting them to smaller wheels. This configuration maximizes stability for hard edging maneuvers. Wheels with a rounder profile are preferred, as they offer improved grip and control during sharp turns at all edging angles.[43]: 19–24 [37]: 37–38  Many hockey skates use a hi-lo wheel setup, with larger wheels in the rear and smaller ones in the front. This raises the heel and lowers the toe cap, thus the name hi-lo. It causes a player to forward flex naturally, for greater stability and stronger strokes.[63]

The modern inline skate was originally created by Scott Olson as a substitute for ice hockey skates, featuring a boot with a hard shell, pivoting cuff, and removable liner.[33] This style of boot construction remains popular across all inline disciplines, ironically with the exception of inline hockey. Instead, hockey boots have followed their own path.[64][K] They are built to be as lightweight as economically feasible while still delivering excellent heel and ankle support, along with protection against impacts from flying pucks. Direct and immediate power transfer from foot to wheel is also essential. To achieve this, hockey boots are constructed around an unyielding wall with anatomical contours to hug the heel and both sides of the ankle. This structure is called the quarter package, made of left and right quarter panels bolted to a rigid outsole platform.[62][60] The rest of the boot is built around this base, including a thick tongue that supports the shin in a forward-leaning athletic stance, and a reinforced toe cap. The liner is integrated into the boot and not removable, with strategically varied thickness for best anatomical fit. Hockey skates are secured with eyelets and laces, rather than buckles or straps.[65][61]

### Speed

[edit]

Main article: Types of inline skates § Speed

Speed skate with 100/90 mm wheels

Speed skates (or race skates) are purpose-built inline skates with a single goal: speed. They enable a racer to generate the most efficient strides and to glide with the least amount of friction.[66]: 3–9, 283–318  Joey Mantia holds the world record for the outdoor 10-kilometers at over 27 miles per hour.[67]

Speed skating differs from other inline disciplines in that a speed skater tilts her body trunk forward for up to 60° when racing, to reduce air resistance. A speed skater bends her knees aggressively for up to 80° in a deep-seated squatting position which requires a deep forward leaning of the shin (dorsiflexion) for proper balance. This deep squatting posture produces the most powerful push-offs, with the farthest displacement of the pushing skate.[66]: 5–11

Inline racing

Because of the need for a deep dorsiflexion, speed skates have no eyelets, buckles, or straps above middle eyelets at 45° angle. In order for racers to freely flex their foot around ankle bones, speed boots are cut the lowest among all inline skates, around or below the ankle bones. The removal of shaft and cuff significantly reduces a boot's weight. [37]: 17, 34–36 [66]: 3–30, 308–311  Most speed boots are custom-fitted without much padding, or else heat-moldable, to prevent the foot from the slightest wobbling.[68][L]

The frame may be made of aircraft-quality aluminum, magnesium, or possibly lightweight carbon fiber, such that it flexes very little and transmits power from the foot to the wheels more directly. The length and height of a frame determine the number and size of wheels it can accommodate. More wheels and bigger wheels increase mass, making acceleration harder and slower. But once rolling at speed, a skater can more easily maintain top speed given the rotational inertia. In the 21st century, wheel size ranges from 90 mm to 125 mm. A setup with four 110 mm wheels (4x110mm) is typical for competitive speed skating, and three 125 mm wheels (3x125mm) for marathon skates at marathon events.[37]: 18–24, 34–36 [70] Speed skates generally adopt either the 165mm or the 195mm mounting standard. Both of these 2-point mounting standards feature a built-in heel lift that pitches a skater forward, creating forward flex.[71]

Bullet profile: striding vs gliding

Speed skating generally adopts harder and high-rebound wheels to minimize energy lost to elastic hysteresis. Speed wheels have a pointy bullet profile that reduces friction from drags when gliding upright, while still providing a large contact surface for improved traction and control when pushing off at a deep edging angle.[66]: 315–316  Speed skaters use High-quality bearings with precision ratings, and perform regular cleaning and lubrication to remove trapped dirt and restore them to their optimal performance.[27]: 128–130

### Urban

[edit]

Main article: Types of inline skates § Urban

Urban skate with 3 big wheels

Urban skate is an umbrella term for a type of skate suitable for several niche inline disciplines: freestyle skating, slalom skating, wizard skating, city commuting, and urban skating. These activities take place on relatively flat ground, but the surface may not always be paved or smooth.[51]

Freestyle skating is named after its counterpart in skateboarding, just like aggressive street, park, and vert skating are named after street, park, and vert skateboarding, respectively. Freestyle skating is the art of performing skating tricks on relatively flat ground, free of obstacles.[72] Freestyle slalom skating is a form of freestyle skating where tricks are performed around slalom cones. This is standardized by the International Freestyle Skaters Association (IFSA) and World Skate as freestyle slalom to distinguish it from speed slalom, which is a form of speed skating around cones on flat ground.[73][74] Freestyle skating requires skates that support rigorous turning and edging maneuvers, with characteristics similar to hockey skates. A rockered setup with 76-80 mm wheels on a relatively short frame is common for freestyle skating.[75]: 15–25 [52]

Urban skating in Bonanjo Heel-to-toe drop on a Trinity frame

Urban skating and city commuting take the activity to the street. But the term 'street skating' is already taken as a subdiscipline of aggressive skating, for grinding on street obstacles. Thus, this niche market is variously promoted as skating on paved roads or commuting to work on skates. These activities demand longer frames and larger wheels for higher cruising speed, stable tracking, and more comfortable rides on uneven surfaces, similar to speed skates for marathon events. Common wheel setups include 4x80mm, 4x90mm, 4x100mm, 3x100mm, 3x110mm, and 3x125mm.[51][52] Most urban skate boots support either the 165mm or Trinity mounting standard, and can be customized with a short frame and average-sized wheels for slalom skating, or with a long frame and large wheels for long-distance road skating.[55][76] Both the 165mm and Trinity mounting standards raise the heel mounting platform higher than the toe, creating a slight heel-to-toe drop, also known as a heel lift. This drop causes the skater to lean forward by default, simulating a subtle forward flex similar in purpose to the hi-lo wheel setup used in hockey skates.[55][77]

Wizard skating is named after the company Wizard Skating, founded by Leon Basin in 2014. This form of skating is characterized by flowing footwork from freestyle, slalom, and figure skating, while a skater blazes through roads, rolls over curbs, skates up ramps, bashes down stairs, and parkours on walls. Leon perfected a type of "Wizard" skate for this sport, featuring a long frame, large wheels, and a rockered wheel setup for either 4 wheels or 5 wheels.[78][52] Skaters are increasingly referring to this style as flow skating.[41]

## Boots

[edit]

### Hard boots

[edit]

Hard boot with pivoting cuff, top buckle, 45° velcro strap, laced front facing, and removable liner

Hard boots dominated the inline skate market in the 1980s and 1990s at the inception of modern inline skating. They are made of plastic, fiberglass, carbon fiber, or other solid materials. A removable liner in a hard boot provides a snug yet comfortable fit between a skater's foot and the hard shell.[48][42][79]

Hard boots use a combination of velcro straps and plastic buckles as closures. Some also use laces for the facing of the boot, while others have a front strap (or buckle) instead of or in addition to laces. The front lace and top buckle secure the foot inside the boot. To achieve proper heel lock, the liner is shaped to fit the heel, and the 45° strap (or buckle) presses the instep of the foot against the contour of the liner.[37]: 15–18

Hard boots have a high cuff (or shaft) to provide proper ankle support. In order to accommodate dorsiflexion, the cuff is made to pivot near the ankle bones. As a skater leans their shin forward, the hinged cuff rotates to follow the lower leg while continuing to provide lateral ankle support.[37]: 15–18

Molds used in plastic injection molding are expensive to make. As a result, plastic hard boots are usually available only in so-called "dual sizes". One hard shell is made for two US and EU shoe sizes (e.g. US 9-10, and EU 42-43). A thicker liner is provided for US 9 and EU 42 to fill the gaps, while a thinner liner is provided for US 10 and EU 43. Some manufacturers offer "dual fit" liners, where the same liner can accommodate two shoe sizes using elastic parts, memory foam, and other compressible space-filling materials.[48][37]: 15–18

### Soft boots

[edit]

K2 Fatty SC, 1997

K2 introduced soft boots to inline skating in 1993 with its Exotech line of recreational skates, marking the company’s entry into the sport. Building on this innovation, K2 later released the legendary K2 Fatty, an aggressive skate featuring the same soft-boot design. Since then, similar soft boots have come to dominate the recreational skate market.[80][81]

They are akin to hiking shoes, made of textiles, mesh, neoprene, and other soft materials. Liners are integrated into the soft boot, and are thus not removable or replaceable. A soft boot is reinforced in strategic areas with a plastic exoskeleton for structural support.[42][79][37]: 15–18

Rollerblade soft boots Fila soft boots

A soft boot uses a pivoting cuff to support the lower leg, like hard boots. Otherwise, its exoskeleton covers only a small area of the foot. This allows the boot to provide superior airflow through its fabric for moisture extraction, to keep the foot cool.[48]

Soft boots use closure systems similar to those of hard boots. These include laces, velcro straps, and buckles. Lacing the front of the boot is key to securing the foot within the boot, due to the lack of exoskeleton support in this area. On the other hand, the flexible front of the boot readily accommodates different shapes of foot. Soft boots thus provide a more comfortable fit at the expense of reduced rigidity and support, making them suitable for beginners and casual skaters. Committed enthusiasts, however, generally avoid soft boots due to their lack of direct and immediate response to skating moves, a result of elastic hysteresis.[48]

Soft boots are lighter and generally more affordable than hard boots. They are also easier to manufacture in precise shoe sizes. While hard boots typically come in dual sizes, soft boots are available in half sizes for US shoe measurements (e.g., US 9.5, 10, and 10.5) and, in some cases, for EU sizes as well (e.g., EU 39.5, 40, and 40.5).[48][37]: 15–18

### Hybrid boots

[edit]

Hybrid soft boot

Endoskeleton shell

Carbon shell

Foot and shell

Hybrid boots, also known as hybrid soft boots, look superficially similar to soft boots, complete with soft materials covering a large part of the boot. Unlike soft boots, however, hybrid boots have no exoskeleton reinforcement apart from the pivoting cuff. These boots have an endoskeleton instead, in the form of a composite shell. The shell serves as the sole of the boot, with shell walls extending upward from the sole. The soft upper part of the boot is pulled taut over the shell and glued onto it.[42][48]

Hybrid boots are lighter than hard boots and soft boots. Yet they remain rigid where the foot meets the boot. Integrated liners in hybrid boots can be made thinner than removable liners in hard boots. In higher-end hybrid boots, the integrated liner is heat-moldable for the best custom fit, and the shell is made of carbon fiber. A hybrid shell sits much closer to the foot than a hard shell or the exoskeleton of a soft boot. As a result, hybrid boots provide more direct and responsive power transfer from a foot to wheels.[42][82]

Hybrid boots originated from the development of carbon shells in speed skates during the 1990s and 2000s. In the 2020s, manufacturers like Powerslide offer hybrid inline skates, including models such as the Hardcore Evo, Tau, and Swell. However, the term "hybrid" has yet to gain universal acceptance, and these boots are often marketed as high-end soft boots.[42][83][84]

### One-piece carbon boots

[edit]

Monocoque shell

TF Pro inline skate vs. ice skate

Main article: Types of inline skates § One-piece carbon boot

In the 21st century, hockey skates increasingly favor one-piece carbon boots with a monocoque shell that were first developed in the 1990s for speed skating. These boots are unlike the three common types of inline boots: hard, soft and hybrid. The one-piece boots are built around a carbon fiber-reinforced composite shell, where the shell almost completely surrounds a foot. After eyelet holes are punched out of a shell, the shell is usable as a functional boot if laced.[85]

For instance, Easton's Synergy 1300C came out in 2005, with a unitary shell made with carbon and aramid fibers. This is widely recognized as the first retail hockey skate with a composite shell.[86][87] Heat molding became possible in 2006, with the Easton Synergy 1500C.[88][89] Other hockey makers, such as VH Hockey, took it one step further, creating a single, unbroken composite shell that also incorporates the "facing" portion where eyelets are located.[82] A heat-moldable monocoque shell requires no breaking-in, unlike traditional hockey skates.[90]

True Temper Sports bought VH Hockey in 2016, and started to mass produce retail hokey skates with heat-moldable monocoque shells, as well as scaling up 3D scanning of feet at retail stores for custom True hockey skates,[90][91][92] leading to inline hockey skates such as the TF9 Roller Skate, and the TF Pro Custom Roller Skate in 2020.[93][94]

## Frames

[edit]

Frame and wheels

Main article: Inline skate frame

An inline skate frame, sometimes referred to as the chassis in certain disciplines such as hockey,[93] serves as the structural link between the boot and the wheels. It connects to the ground through the wheels mounted on it, and to the skater's foot through the sole of the boot.

### Frame dimensions

[edit]

Main article: Inline skate frame § Dimensions

Frame length, also known as wheelbase, refers to the distance between the centers of the first and last wheel axles. In disciplines like hockey and slalom, skaters use short frames with closely packed wheels to enhance maneuverability and enable fluid footwork. In contrast, speed skating relies on longer frames, which space out the wheels to provide greater stability at high speeds.[95]

Level deck height (UFS) vs. raised heel (Trinity)

Frame height, deck height, and ride height are related but loosely defined terms in inline skating. All three describe how low a boot can be positioned relative to the ground in a given setup, considering the number and size of the wheels. Ideally, a skater wants the boot as close to the ground as possible, while allowing enough clearance between the sole and the wheel tops for free rotation.[96][97] All three terms may refer to the distance from the frame's deck to the wheel axle center, excluding wheel size. In other cases, they are defined as sole-to-ground distance, incorporating both the structure of a frame and of actual wheel size.[M][95][98]

### Frame rigidity

[edit]

Main article: Inline skate frame § Rigidity

Plastic frames Extruded & milled aluminum

Frame rigidity is essential for an efficient transfer of power from a skater's foot to the ground. A rigid frame does not suffer from elastic hysteresis.[37]: 18–21  For this reason, even entry-level inline skates often use fiberglass-reinforced plastic, instead or softer but cheaper plastic to make frames. For a stiffer yet lightweight frame, aircraft-grade aluminum alloys such as the 6000 and 7000 series are used. Hockey and speed skating often call for magnesium frames, which are even stiffer and lighter than aluminum. Some speed skaters use carbon fiber frames that are the most rigid and lightweight frames available.[55][99]

Rigidity of a frame is an important factor in choosing one. However, other considerations, including cost and weight, also influence the decision.[100] Sometimes, a discipline's needs trump many of these factors. For instance, aggressive skaters exclusively use fiberglass-reinforced plastic frames for their superior performance and consistent friction when grinding against all types of surfaces.[40]: 138  Some of the most rigid frames, such as those made of carbon fiber, can be too brittle for hockey. These frames shatter rather than deform under impact or extreme stress due to their low fracture toughness.[101] In addition, some skaters value comfort, which is at odds with rigid frames; increased rigidity transmits all imperfections of the road surface to the skater unattenuated, reducing comfort.[102]

### Rockerable frames

[edit]

Toggleable frame: 1980s

Toggleable axles: 2020

Pre-rockered: 2025

Main article: Inline skate frame § Rockerable

Wheel rockering can be achieved by using wheels of different diameters, or by using a frame with built-in support for a rockered arrangement of identical wheels. Such rockerable frames may be configured in either a flat setup for long-distance skating, or a banana-rockered setup for highly maneuverable disciplines like hockey, with sharp turns and quick footwork.[33]: 81–86 [75]: 20–21

Some frames are compatible with toggleable hardware for quick and reliable switching of wheel setups. These involved the use of frame spacers, axle guides, mounting hole inserts, or axle bolts that fit oblong mounting holes in two or more ways, in order to shift the axle’s center to a preset position.[38]: 44–45 [N]

With the advent of mounting standards and easily-swappable frames in the 21st century, some inline frames now eschew toggleable hardware in pursuit of reduction in complexity, weight, and number of components. Each brand offers its own pre-rockered frame with custom axle holes to create a wheel arrangement that it deems optimal.[75]: 20–21 [104]

### Non-standard frames

[edit]

Main article: Inline skate frame § Non-standard

USSR skates (1960s) PS One Zoom (2024)

Modern inline skates began as off-season training tools for ice skaters.[55] Early frames, including those used by the USSR speed skating team in the 1960s, featured adjustable lengths and variable wheel positions to fit different shoe sizes.[20] This approach continued in the 1966 Chicago Roller-Blade and early 1980s Rollerblade skates.[B][O] Early inline skates lacked mounting standards. The 1962 USSR skate and 1966 Chicago Roller-Blade fit flat-soled shoes, while the 1975 Super Sport Skate, modeled after hockey boots, used a raised heel mount that created a built-in heel lift.[C]

Non-standard frames still dominate entry-level skates and are often non-replaceable. Most lack adjustment for pronation or supination. Some, like the 2024 Powerslide One Zoom, use riveted frames that cannot be customized.[55] Outside the entry-level market, most inline skates follow one of three mounting standards: UFS, 165mm, or Trinity.[96][97] The exception is hockey skates, which still use riveted mounts like ice hockey boots. All hockey skates, from budget to hig-end custom models, have proprietary, non-replaceable frames.[H]

### 165mm and 195mm frames

[edit]

Main article: Inline skate frame § 165mm and 195mm

165mm speed boot

In 1974, Inze Bont introduced fiberglass speed skate boots with 165 mm mounting holes for attaching adjustable ice blades.[55] As inline skating grew in the mid-1980s, brands like Darkstar, Mogema, and Raps created frames to fit these boots, establishing the first inline skate mounting standard: the 165mm 2-point system.[106]

Rollerblade Twister 80 with a 165mm mount

Later known as SSM (Standard Speed Mount),[107] this standard features a 10 mm heel lift that enhances power in push-offs through deeper ankle flexion.[71] The standard does not specify a frame width, mount width or exact mounting locations on the boot.[55] In practice, Bont boots offer only minimal mounting areas. But compatible frames can still be secured with minimal flex, especially with Bont's later kevlar and carbon boots.[108] Roces Impala skates brought the 165mm standard outside of speed skating in the mid-1990s, expanding it to recreational, aggressive, and slalom skating. However, softer soles in these boots may flex under load, prompting reinforcement with metal plates.[55]

Originally designed for five small wheels (e.g. 5x80mm), the 165mm layout caused bolt interference as 4x100mm setups with longer frames became common, forcing frames to become taller.[109] To address this, the 195mm 2-point LSM (Long Speed Mount) was introduced in 2003.[110] It allows longer frames and larger wheels, while retaining the same heel lift, without adding additional height.[111] This design provides a stable ride at high speeds by maintaining a relatively low center of gravity in proportion to the longer wheelbase.[112][95] While LSM is mainly used in speed skating, many frames now include slots to fit both standards.[76]

### UFS frames

[edit]

Main article: Inline skate frame § UFS

K2 Fatty Pro

5th Element

Aggressive inline skating gained mainstream attention after its 1995 ESPN X Games debut, sparking rapid growth and specialized skate development.[113] Released in 1996, the K2 Fatty was the first skate to integrate the frame into the soulplate, reducing height differences and replacing the traditional two-part platform with a solid rectangular structure.[114][115] In 1998, Roces released the 5th Element, an aggressive skate that combined the soulplate and frame into a single flat unit with no height difference between front and rear. This flat sole improved soul grinds and influenced other skate designs.[116]

UFS patent drawing (left). Razors Shift - UFS boot and frame (right).

In 1999, Salomon, USD, Razors, Kizer, 7XL/Able, and Fifty/50 developed the Universal Frame System (UFS), a standardized mounting system for aggressive skates. It used a flat rectangular surface 41 mm wide with two holes spaced 167 mm apart, aligning with the trend of flat soulplates. Salomon's 2001 Aaron Feinberg Pro Model was the first skate to feature UFS and quickly became a popular industry standard.[54][117][118]

Unlike other mounting systems of the time, UFS eliminated built-in heel lift, positioning the heel level with the toes for the first time. However, most brands followed Salomon’s lead in incorporating a thick shock absorber at the heel. This provided better impact support for hard landings from high jumps, but accidentally reintroduced a small amount of heel lift.[114][119]

### Trinity frames

[edit]

Main article: Inline skate frame § Trinity

A Trinity boot & frame

The 165mm standard, originally from speed skating, has dominated since the mid-1990s, except in aggressive (UFS) and hockey (riveted) skates. But its small mount area can cause frame wobble on boots without stiff soles or reinforced platforms.[55] As larger wheels became popular, 165mm frames adapted with taller designs or altered wheel placement to fit bigger wheels. Some raised frame height, reducing stability,[71] while others downsized or shifted middle wheels to avoid bolt interference.[120] Some brands shifted mount platforms, leading to front-back centering issues when mixing boots and frames.[109] Introduced in 2003, the 195mm standard supported larger wheels without raising frame height or altering wheel placement.[110] However, its extended front-to-back spacing exceeded the optimal heel-to-ball length, requiring ultra-stiff soles not found outside the speed skating market until the late 2010s, limiting adoption to carbon-fiber speed speed boots.[70] [121][122]

Trinity mounts

In 2016, Powerslide introduced the Trinity mounting system to support modern wheel setups while addressing the limitations of the 165mm and 195mm standards.[123] Unlike two-point systems, Trinity uses three mounts. The two front bolts are offset, placed beside the centerline to allow front wheels to sit closer to the sole.[124] The rear mount, located under the heel, is raised by 10 mm to clear the rear wheels and create a heel lift similar to the 165mm standard. The three bolts form a triangular layout measuring 150 mm, 135 mm, and 55 mm.[77] This design aligns with foot anatomy for improved heel-to-ball support and structural stability.[95][121]

Trinity specifications

A Trinity frame typically wobbles less than 165mm or 195mm frames on similarly stiff boots. Unlike 165mm setups, which rely on the sole acting as a cantilever around central bolts, Trinity distributes support across the full width of the ball of the foot, similar to a hockey blade holder. This wider support reduces cantilever stress, improving power transfer and edge support.[125][126]

A Trinity frame typically has a lower "front" mount height than its 165mm counterpart when using the same wheel setup. This is because the front mount of a Trinity frame can be positioned significantly lower than the tops of the front wheels due to its open centerline, allowing the front of the boot to be moved as close to the ground as the front wheels allow. This lowers the skate’s center of gravity, improving control and stability.[98]

### Heel brakes and toe stops

[edit]

Main article: Inline skate frame § Heel brakes and toe stops

Heel brake Inline figure skate

A heel brake is a hard rubber stopper attached to the back of the frame that lets skaters stop by lifting their toes and pressing it to the ground. It is especially important for beginners, offering a simple way to stop quickly and control downhill speed. Recreational and fitness skates usually include one brake, mountable on either skate, with most righthanded skaters choosing the right.[27]: 25–26

Heel brakes can interfere with advanced techniques like crossover turns, which are essential in hockey and speed skating. They also hinder freestyle slalom tricks and aggressive grinds. As a result, skates made for racing, hockey, slalom, and aggressive skating typically do not include a heel brake.[127][37]: 30–38  Some urban skates include an unattached brake, while others cannot support one at all. Many experienced skaters remove heel brakes after learning other stopping methods, such as the T-stop, which uses friction from dragging one skate behind the other. However, these techniques wear down wheels, so some skaters prefer slalom moves and controlled turns to avoid obstacles and reduce wear.[37]: 87–96, 101–114 [75]: 24

Inline figure skates are unique among inline designs in that they use a toe stop instead of a heel brake. Toe stops are essential for performing many artistic roller skating moves and jumps.

## Wheels

[edit]

Main article: Inline skate wheel

### Polyurethane wheels

[edit]

Main article: Inline skate wheel § Polyurethane

Small & hard wheels

large & soft wheels

Rebound improves performance

Modern inline wheels are made of polyurethane (or urethane), a versatile elastomer that transformed skating.[128][129] It can be molded into any shape and customized for color, hardness, grip, and rebound, enabling specialized wheels for various skating disciplines.[130][P] Polyurethane also offers high elasticity, or wheel rebound, without compromising other properties. This rebound helps convert stride energy into acceleration, benefiting all types of inline skating.[132][Q][37]: 24–26

Before polyurethane, roller skates and skateboards used composition wheels made from clay or rubber mixed with fibers.[133][R] In the early 1970s, roller skaters tested polyurethane wheels but found them too grippy and slow for wooden rink floors, where composition wheels worked better. By the mid-1970s, skateboarders repurposed polyurethane wheels from roller skates, shaving them to fit. Their elasticity improved rides on rough surfaces and helped revive skateboarding after its decline in the late-1960s.[136][137][138]

In the early 1980s, Scott Olson similarly repurposed polyurethane wheels from roller skates, shaving down tens of thousands to fit the skates sold by his company, Ole’s Innovative Sports – later known as Rollerblade. The same qualities that made polyurethane wheels ideal for skateboarding, such as durability, impact resistance, and a smooth ride, also benefited inline skating. This innovation helped bring inline skating out of obscurity and transform it into a popular outdoor sport during the 1980s.[139][29][20][130]

### Wheel structure

[edit]

Main article: Inline skate wheel § Structure

Wheel cross section

Modern inline wheels consist of two main components: an outer polyurethane tire, shaped like a donut, and an inner plastic hub, also known as a core. The hub features a hollow center designed to accommodate a spacer and two ISO 608 ball bearings. Made of hard plastic, the hub securely holds the bearings in place through a friction fit - something the softer polyurethane tire cannot achieve. On the other hand, the soft polyurethane tire is able to deform upon ground contact, cushioning the landing and gripping the ground.[103][P][45]

Polyurethane tire molded over a plastic hub - 1988 Rollerblade Lightning patent (left) and skate (right)

From the 1910s to the 1970s, many wheeled skates served as precursors to modern inline skates. Most of these early skates featured small wheels made of rubber or rubber reinforced with fibers, often with relatively simple constructions.[19][21] In the 1980s, Rollerblade collaborated with Kryptonics to develop polyurethane wheels for inline skates. The inline industry adapted plastic hub innovations from roller skates, integrating them into inline wheels. These wheels were manufactured by placing a plastic hub at the center of a mold and then pouring molten polyurethane around it. The liquid polyurethane flowed into cavities and holes in the hub before settling. As it cooled and solidified, it formed a secure interlock with the hub.[N][S]

### Wheel hubs

[edit]

Clear polyurethane tire molded over interlock vanes of a plastic hub

Chemically-bonded interlock rim (left) vs. mechanical interlock (right)

Main article: Inline skate wheel § Hub

The outer rim of the hub, known as the interlock, is buried within the polyurethane tire. Unless the tire is made from clear urethane, this rim remains hidden from view. Beyond mechanically securing the tire to the hub, the interlock rim also enhances the wheel’s overall structural rigidity.[T][S][140] Some manufacturers apply a bonding agent to the hub before pouring the polyurethane, creating a chemical bond that reduces reliance on mechanical interlocking. Others use polyurethane-blended plastic hubs that bond chemically with the polyurethane tire during molding.[P][141]

The visible hub size varies with wheel dimensions and skating discipline. In small aggressive skating wheels, the hub may be just a thin ring housing the bearings. In contrast, 82 mm racing wheels from the 1990s had hubs taking up nearly half the diameter. By the 2020s, 110 to 125 mm wheels often feature hubs that occupy most of the wheel's diameter.[43]: 19–24 [37]: 26–27 [142]

Hubless (no core), closed core & open

A wheel's volume grows with the square of its diameter. Large solid wheels would be too heavy for inline skating, so designers adopted stroller wheel concepts, using lightweight spoked hubs with interlock rims to hold the tire. These spoked hubs, or open cores, have an outer rim connected to the bearing housing by spokes. Full hubs, or closed cores, are solid discs with no visible separation. Semi-open cores fall in between, with solid discs and small hollows drilled to reduce weight.[143][130]

Spoked cores are generally lighter than full cores but may offer reduced rigidity and structural integrity. Aggressive skaters prefer small wheels with robust full cores for durability during jumps and landings. Speed and marathon skaters use large wheels with spoked hubs, which allow air to circulate around the hub, and help cool the bearings. Without adequate heat dissipation, the polyurethane tire may soften, increasing deformation during rolling and potentially leading to separation from the hub.[45][103][144]

### Wheel diameter and profile

[edit]

Common diameters and profiles

Main article: Inline skate wheel § Diameter and profile

Inline skate wheels in the 2020s range from 55 mm to 125 mm in wheel diameter, but their width remains standardized at 24 mm.[145][140] Frames are built for specific setups, each fitting a set number of wheels of certain diameters, yet all assume a 24 mm hub width.[45][146] The wheel profile describes the shape of the contact surface when viewed head-on. Although any diameter can be matched with any profile, certain combinations work better for specific skating styles.[147][148]

Flatish (60 mm)

Small wheels used in aggressive skating, typically 55 to 64 mm in diameter, often have a flat contact profile resembling a rounded rectangle like car tires.[144] This shape provides strong grip and stable upright rolling, ideal for rolling upright.[148] While flat profiles were popular in the 1990s, modern aggressive skaters increasingly favor slightly rounder profiles for better balance between stability and maneuverability.[149]

Round profile (80 mm) & edging angles

Most inline wheels are medium-sized with a round profile, since skaters often tilt their skates rather than always keeping them fully upright. Many techniques involve edging, or skating on the wheel sides, which requires a consistent contact surface at various angles.[D][49] Round profiles support this, even if the contact area is smaller than that of flat wheels. Inline hockey and freestyle slalom often use round-profile wheels up to 80 mm in diameter.[147][140]

Bullet profile (110 mm) & striding/gliding

At the opposite end of the spectrum from the flat profile is the bullet profile, also known as the pointy, thin, narrow, or elliptical profile. It is common in large wheels from 90 to 125 mm and suits the needs of speed skating.[38]: 51–52 [130][148][52] It helps skaters achieve two seemingly conflicting goals. The first goal is to maximize grip (or static friction) during deep edging, allowing skaters to convert lateral push-offs into forward motion over a longer stride. The second goal is to minimize rolling friction (or rolling resistance) when upright, enabling longer, faster glides with less energy loss.[45][66]: 316

Large wheels act like flywheels, storing rotational energy that helps skaters reach and maintain high speeds over long distances. Their gyroscopic effect stabilizes direction, reducing energy loss from lateral drift. However, their greater mass makes them slower to accelerate.[45][37]: 24–25  In contrast, small wheels have lower rotational inertia, allowing faster starts and quicker maneuvers. They also lower the center of gravity for better control, but give a bumpier ride and perform poorly over bumps, cracks, sticks, and pebbles.[79][145]

### Wheel hardness and deformation

[edit]

Wheels deform under the weight of the skater

Main article: Inline skate wheel § Hardness and deformation

Polyurethane wheels deform under a skater's weight, which increases ground contact and improves grip. This contact area, known as the footprint, differs slightly from an unloaded wheel's profile.[46][45] The ideal deformation varies by surface. On slippery indoor rinks with polished wood floors, softer wheels are better because they deform more and enhance traction. On rough outdoor asphalt, harder wheels are preferred since the surface already offers enough grip with minimal footprint.[75]: 18–19 [142][150] Balancing grip is essential. Too little grip causes slipping during strides, wasting energy. Too much grip creates rolling resistance, sapping speed during glides.[45][46]

76A indoor

84A outdoor

88A urban

90A aggro

Rolling resistance is generally higher with softer wheels because they deform more, while harder wheels require less effort to start rolling and maintain speed on smooth surfaces. However, on rough terrain, hard wheels can increase rolling resistance by wasting energy as they repeatedly lift skater's weight over bumps, thus offsetting their typical quick acceleration and higher sustained speed. Softer wheels, though slower due to deformation, absorb surface irregularities better and help minimize energy loss in addition to providing a smoother ride.[151][152][153]

Wheel deformation depends on the skater's weight, the wheel's hardness, and its temperature. While weight and hardness stay constant, temperature varies with ambient conditions, surface heat, and bearings friction from high-speed skating. As temperature rises, the polyurethane softens, causing the wheel to deform more and reducing its effective hardness.[N][154][45]

Wheel hardness is measured on the Shore A durometer scale, which ranges from 0A (softest) to 100A (hardest). Inline skate wheels usually range from 72A to 95A. Indoor hockey wheels are softest at 72A to 78A. Recreational outdoor wheels are slightly harder, between 80A and 84A. Freestyle slalom and urban wheels range from 83A to 88A, while aggressive skating wheels are hardest at 88A to 95A.[43]: 21–22 [147][150][142]

Within the appropriate hardness range for an activity, softer wheels offer better grip for quicker acceleration during lateral strides, and a smoother ride on uneven surfaces, though they wear out faster. Harder wheels allow for higher gliding speeds, resist wear on rough surfaces, and offer a more responsive feel, but they can lead to a bumpier ride and some energy loss.[155][142]

### Dual density wheels

[edit]

Main article: Inline skate wheel § Dual density

Dual density wheels were developed to address the long-standing challenge of choosing a single wheel hardness to meet opposing needs. Softer wheels provided shock absorption over rough terrain and better grip at deep edging angles, while harder wheels offered greater wear resistance and higher speeds on smooth, upright glides. Skaters had to compromise, as no single hardness met both demands effectively.[156][157]

Dual durometer wheel

Soft tire molded over harder support

In 1997, K2 patented a dual durometer wheel, later known as a dual density wheel, aimed at combining a smooth ride over rough terrain with the durability and speed of hard wheels. Unlike single-compound wheels, it used two layers: a hard outer tire (70A to 100A) for wear resistance and speed, and a soft inner ring (20A to 75A) to absorb shocks and vibrations.[156]

In 1997, Neal Piper and Tom Peterson of Hyper Wheels patented a similar dual-layer wheel concept, but used a triangular foam mandrel instead of a soft polyurethane ring. This design aimed to match the benefits of K2’s dual-durometer wheels, while also improving grip during deep edging. The foam mandrel's shape prevented deformation at the wheel’s tip during upright skating, while allowing the sides to flex under angled loads, enhancing grip during strides and turns at about a 30° tilt.[46]

In 2004, Neal Piper patented a multi-density wheel that reversed his 1997 design by using a soft outer polyurethane layer (60A to 75A) over a much harder internal support structure (80A to 95A or more). First seen in Revision Variant hockey wheels and later in the Recoil and Flex lines, this design gave hockey players top speed without sacrificing high grip.[158][159][45]

### Wheel rebound

[edit]

Main article: Inline skate wheel § Rebound

Rebound improves cornering

Wheel rebound is the energy a polyurethane wheel returns as it recovers its shape after being deformed. Though widely discussed, there is no consensus on how to rate it.[37]: 24–26  Unlike other wheel traits that depend on skating style or terrain, rebound is universally desired. Higher rebound is always preferred, if cost were not a factor.[150]

High rebound wheels feel lively and responsive

High-rebound wheels feel lively and responsive, helping skaters roll faster with less effort by converting more energy from each push into forward motion.[132] Low-rebound wheels feel dead, absorbing energy like flat tires and requiring more effort to maintain speed, similar to walking on soft sand.[154]

A polyurethane compound can be formulated with varying rebound levels regardless of hardness. Hardness affects how much a wheel compresses under load, while rebound measures how much of that energy is converted to aid forward motion. These are separate, distinct properties.[Q]

Rebound can be measured using tests like the Bayshore Resilience test, which compares rebound height to drop height, and the Rebound Resilience test, which measures percentage of energy return. These tests assess polyurethane resilience, another term for rebound, but their quantification of elasticity are not directly comparable. Inline skate wheels rarely list rebound in technical datasheets, and when they do, it’s usually under vague labels like High Rebound (HR) or Ultra High Rebound (UHR).[160][146][140]

In mechanics, rebound is closely linked to elastic hysteresis, its complementary property, which measures energy lost as heat during deformation and recovery. The two are inversely proportional: higher hysteresis means more energy loss and lower rebound.[161]

### Rolling resistance

[edit]

Main article: Inline skate wheel § Rolling resistance

Minimizing rolling resistance

Surfaces: rough vs. smooth

Rolling resistance, or rolling friction or drag, is a key factor limiting a skater's top speed. It opposes wheel motion and is mainly caused by elastic hysteresis.[66]: 316 [46] To reduce it, manufacturers design polyurethane compounds for high rebound and thus low hysteresis, which is especially important in speed skating.[151][75]: 18–19

Skater weight and wheel hardness affect wheel deformation and footprint size, which influences rolling resistance. Speed skaters prefer hard, pointy-profile wheels to keep footprints small and reduce resistance, while gliding upright. Dual-density wheels were developed to minimize footprint while preserving comfort.[66]: 316 [46]

Terrain roughness also affects rolling resistance, as energy is lost repeatedly lifting the skater over small surface imperfection. The need to cushion bumpy rides without increasing the footprint was another driving force behind dual-density wheels.[152][156][153]

Wheel diameter plays another key role in rolling resistance, especially on rough terrain. Larger wheels reduce resistance by smoothing out surface imperfections and lowering the angle of contact with bumps. This reduces energy loss. As a result, wheels between 90 mm and 125 mm are common in urban and marathon skating, where both speed and handling uneven surfaces are important.[153][152][52]

## Bearings

[edit]

Function Grooves & balls

Main article: Inline skate bearing

Ball bearings allow inline skate wheels to spin freely by separating the moving wheels from the non-moving structure.[162] Wheels rotate around axles that are tightly bolted to the frame, which is securely attached to the boot using fasteners. Bearings minimize friction between the wheel and axle, enabling greater speed with less effort.[37]: 26–29, 39–45 [U] The adoption of modern ISO 608 ball bearings, combined with polyurethane wheels, helped propel inline skating to peak popularity in the 1990s.[139][41]

An ISO 608 ball bearing has two concentric rings: an outer race attached to the rotating wheel hub and an inner race fixed to the stationary axle. Between them are 5 to 8 rolling balls. Deep grooves in the races form raceways that hold the balls securely. A retainer, or cage, keeps the balls evenly spaced along the raceways.[163][37]: 26–29, 39–45 [U][164]

### Purpose-built bearings

[edit]

Main article: Inline skate bearing § Purpose-built

The ABEC scale rates bearing precision from 1 to 9 (highest) in odd numbers, originally for high-speed industrial machinery. It does not account for material type, quality, durability, or how bearings handle dirt, moisture, and other factors crucial for skating performance. Higher ABEC ratings show better precision but are only one of many factors in a bearing’s suitability for inline skating.[37]: 27–28 [165] For inline skating, any ABEC-rated bearing is sufficient, considering that an average skater cruising on 80 mm wheels reaches only about 1,326 RPM. This is just 3.5% of the mechanical limiting speed (38,000 RPM) of ABEC 3-rated 608 bearings from SKF.[V][166]

Bones Swiss

Recognizing the unique demands of skating, George Powell worked with a Swiss manufacturer to develop 608 bearings specifically for skateboarding, launching Bones Swiss in 1983. Unlike standard bearings made for electric motors operating in clean environments, Bones Swiss bearings were purpose-built and designed to handle the multi-directional loads from street skating.[167][168] They featured a serviceable outer shield for easy access when cleaning. The inner side was left open, and a molded plastic retainers could be temporarily removed when accessing and cleaning the balls and raceways. Powell also created a custom lubricant suited to skating conditions.[169][162][170]

Reputable skate bearing brands typically avoid ABEC ratings, as they don’t reflect design features specific to skating. Instead, bearings are marketed under specialized product lines. Bones Bearings, for instance, offers Bones Swiss, Bones Swiss Ceramic, Bones REDS®, and Bones Big Balls®, all labeled Skate Rated™ to show they are engineered for real skating demands. Powell’s “Swiss” design and engineering has become an industry benchmark, though some copycat brands sell imitation “Swiss” bearings that mimic the structure and claims without being made in Switzerland.[66]: 317–318 [75]: 22–24 [171][172]

OEM TWINCAM ILQ-7

Simiarly, TWINCAM bearings were created in the early 1990s specifically for inline skating, marketed with the slogan “Beyond ABEC.” In 1991, they introduced serviceable bearings with removable shields held in place with a C-clip, followed in 1992 by TK CLASSIC Racing Gel, a water-repellent lubricant. In 2002, they launched the ILQ-9, a 6-ball bearing, as an alternative to the standard 7-ball setup. The ILQ line later expanded to include models such as ILQ-9 Pro with rubber shields, ILQ-7 for OEM skates, ILQ-X mr2 with reduced weight, and ILQ-Midget with 11 balls. TWINCAM trademarked ILQ (InLine Qualified) as a proprietary rating system, and had various ILQ models rebranded and redistributed by partners such as FR Skates, K2, Rollerblade, and Powerslide/Wicked.[173][174][68]

### Contamination and bearing friction

[edit]

Main article: Inline skate bearing § Contamination and friction

Skaters lose energy not only from wheel rolling resistance but also from bearing friction, caused by internal components like balls, cage, lubricant, and seals.[175][176] However, in clean, well-lubricated bearings, this friction is minimal compared to rolling resistance of polyurethane wheels. Most purpose-built bearings from reputable brands meet or exceed ABEC 3 specs, so bearing selection has little effect on performance when bearings are new.[152][166][66]: 317–318 [75]: 22–24

Dirt trapped inside a bearing

Bearing selection plays a significant role over the lifetime of bearings, though, because performance depends on how well bearings resist contamination from dirt, dust, and moisture. Even microscopic particles can damage raceways and hinder smooth rotation. Contamination is the most harmful factor; it reduces efficiency or causes bearings to seize.[177][168] As skaters say, the fastest bearings in the world are simply ones that are new or freshly cleaned and lubricated.[169][165]

### Bearing shields

[edit]

Main article: Inline skate bearing § Shields

Z shields showing gaps

Inline skate bearings are protected from contamination using four main shield types: non-serviceable metal gap shields (Z), serviceable metal gap shields with a C-ring (ZS), serviceable rubber gap shields bonded to a metal insert (RS), and full-contact labyrinth rubber lip seals (RSL).[162][W][43]: 42–45

Z shields are simple metal covers that snap into the outer race without touching the inner race, leaving a small non-contact gap. They create no drag but offer limited protection and cannot be removed without damage. Bearings with shields on both sides are labeled "ZZ" and are non-serviceable (e.g., Rollerblade SG).[169][182][164][W]

ZS shields released by C-ring

ZS Shields are similar to Z shields, but feature a removable C-clip (C-ring), allowing for easy shield removal for maintenance. They are similarly non-contact and low-drag, and similarly provide minimal defense against dirt and moisture. Their main advantage is serviceability: that skaters can remove and reattach the shields without damage, enabling regular cleaning and relubrication. This design is used in TWINCAM ILQ-style bearings, with double-shielded ones often labeled "2ZS" or "ZZS".[163][162][164][W]

RS shield in Bones Swiss

RS shields use a nitrile rubber shield bonded to a metal insert. In skating, RS rubber shields specifically refer to the design popularized by Bones Swiss. They offer better protection than Z or ZS shields and are removable for cleaning and maintenance. Many skate brands use only one RS shield, leaving the inner side open and protected by the wheel hub, allowing easy lubrication access without even removing the shield.[177][180][181][164][W]

Heavy grease

RSL seals are full-contact rubber seals with a labyrinth lip profile that lightly touches the inner race, blocking dirt and moisture. These are used with thick grease for long-lasting protection with near-zero maintenance, but cause more bearing drag.[164][W] Though they don’t spin freely when unloaded, they perform efficiently under a skater’s weight, when grease is forced away from ball paths as wheels roll. Dragon Bearings produces "2RSL" models with RSL seals on both sides.[175][180]

## Skate tuning

[edit]

Main article: Inline skate tuning

Standard aggro vs. big-wheel urban setup

Skate setup, customization and tuning terms vary by discipline. For instance, urban skaters refers to four larger wheels (e.g. 4x90mm) and triskates with three large wheels (110 mm or more) as big-wheel setups. In contrast, aggressive skaters consider anything 80 mm or larger to be big-wheel.[183][184] On the other hand, large wheels are standard for marathon skaters, and a triskate under 125 mm is seen as small and unusual. Terms like "big-wheel" and "triskate" also imply specific frame and boot designs, as setups with 125 mm wheels need stronger frames and more supportive boots to handle increased speed and leverage.[51][68][184]

Same boot on different frames and wheels

A wheel setup generally refers to both the number and size of wheels. Common examples include 4x80mm for recreational use and 3x110mm, popular with urban skaters in the 2020s. Older 5x80mm setups, once used in speed skating, are now mainly seen in wizard skating.[52][78] Wheel setups also involve wheel arrangement, which affects performance. A flat setup has all wheels touching the ground. A rockered setup raises the front and rear wheels for a curved profile. A hi-lo setup uses decreasing wheel sizes frontward (e.g. 80-78-76-74 mm)), keeping all wheels grounded but raising the heel for a forward-leaning stance.[56][63]

Skaters can customize one boot with different wheel setups for various purposes. A short frame with soft 80 mm wheels suits indoor use, while a longer frame with harder 110 mm wheels works for outdoor distance skating. Some frames, like the Endless 90, support both 4x90mm and 3x110mm setups. Even without changing the frame or boot, switching wheels with different hardness, rebound, diameter, or profile can significantly alter the skating experience.[76][185]

Some components of a skate

An axle assembly includes the rods, screws, bolts, and bushings that secure a wheel to the frame. A bearing assembly has two ball bearings with a spacer and, when placed in a wheel hub with a tire, forms a wheel assembly.[186][187][188] A frame assembly refers to all skate components except the boot and wheel assemblies. For recreational skates, this includes the frame, brake, boot-mounting hardware, and axle assemblies. In aggressive skates, it may also include H-blocks and parts for grinding.[188][189]

### Wheel rotation

[edit]

Main article: Inline skate tuning § Wheel rotation

1-3/2-4 rotation 4-1-2-3 rotation Hi-lo rotation

Inline skate wheels wear down with use and need periodic rotation and eventual replacement. Front wheels and inside edges wear faster, especially on the dominant foot, thus usually the right foot for right-handed skaters. Uneven wear can distort the wheel profile, and severely worn wheels risk de-coring (disbonding from wheel hub) during use.[37]: 45–50 [190]

Regular wheel rotation helps distribute wear evenly, extending lifespan of the entire set. This includes repositioning less-worn wheels to high-wear axles to balance diameter differences, flipping wheels to even out lopsided edge wear from motions such as push-offs, and swapping wheels between skates to address asymmetrical wear from foot dominance.[33]: 81–86 [146][191]

The 1-3/2-4 rotation is a common rotation pattern for four-wheel setups in the 21st century. It exchanges the first wheel with the third and the second with the fourth, repositioning them to balance diameter differences. Simultaneously, wheels are swapped between skates, flipping inside and outside edges to correct lopsided edge wear and foot dominance effects. Eventually, all wheels wear out and are replaced as a set.[37]: 45–50 [38]: 41–45

The 4-1-2-3 rotation is another common method, and it predates 1-3/2-4. This was first documented in the 1985 book Rollerblades: Dryland Training for Ice Hockey. The front wheel moves to the fourth axle, while all others shift forward one position. The 4-1-2-3 rotation lets each wheel pass through all axle positions, promoting even wear and enabling full set replacement when needed.[33]: 81–86 [191][146]

The hi-lo rotation method eliminates abrupt changes in effective wheel diameters which occur with other rotation patterns when all wheels are fully-worn and replaced as a set. With this method, all eight wheels are removed, sorted by observed diameter, and stacked from largest to smallest. The two most worn may be discarded and replaced with new ones. Wheels are then remounted by increasing size, starting with the smallest on the front of the non-dominant skate, and ending with the largest on the rear of the dominant skate. This creates a hi-lo wheel setup that mimics forward flex and maintains consistent ride height across rotations.[191]

### Bearing alignment

[edit]

Recess & abutment Outer/inner races Bearing planes

Main article: Inline skate tuning § Bearing alignment

Bearing misalignment is one of the most harmful issues in skating, second only to dirt contamination in bearings. When customizing or replacing wheels, bearings must be re-installed carefully. Misalignment can cause wheels to tilt, roll unevenly, drag against the frame, vibrate, and overheat. This reduces performance, risks tire debonding, and leads to premature wear of bearings and axles.[192][193][37]: 39–45

In the 1980s, Rollerblade and Kryptonics developed plastic hubs with precise, rigid bearing seats to align bearings accurately. Each 7 mm deep bearing recess matches the width of an ISO 608 bearing, allowing flush mounting with press-fit.[103][194][195] This leaves a 10 mm gap between two bearings mounted on a hub standardized at 24 mm wide. This gap is filled by a bearing abutment molded into the hub to position and support the bearings.[45]

A ball bearing has two concentric races that rotate relative to each other. The outer race is fixed in the hub and rotates with the wheel, while the inner race stays stationary with the axle assembly.[194] A spacer matching the 10 mm bearing abutment fits between the inner races. Tightening the axle bolt clamps the frame around the bearing assembly, creating a rigid structure that binds the axle, spacer, and inner races, securing them to the frame and boot.[103][43]: 19–24 [38]: 43–44

The bearing abutment and outer race of each bearing together define a bearing plane. Both planes should be parallel and exactly 10 mm apart, with the spacer and inner races meeting at these same planes. Proper bearing alignment means all these geometric relationships are correctly maintained.[103][194]

### Side load support

[edit]

Main article: Inline skate tuning § Side load support

Vertical load & radial play Side load and axial play

ISO 608 bearings in inline skates are deep groove ball bearings (radial ball bearings), designed primarily to handle radial loads \- forces applied perpendicular to the axle from the skater’s weight. These loads pass from the boot through the frame and axles to the inner races and balls, pressing against the outer races. Radial load in skating is thus colloquially known as vertical load.[196][197][167]

Radial ball bearings are also capable of handling a certain amount of axial load from both directions. These are side forces along the axle produced by maneuvers that involve a deep edge, such as turning, crossovers, power slides, power stops, and techniques like slalom or the double push. Axial load in skating is colloquially known as side load.[198][197][171]

Some purpose-built bearings, such as the Bones Swiss, are designed with larger internal clearance (gaps between the balls and raceways) to better accommodate side loading.[167][171][197] This enables increased axial play (or axial clearance), an intentional design and not a sign of lower precision. It allows the inner race to shift laterally relative to the outer race, changing the contact angle between balls and raceways to better support axial loads without binding.[199][200][182]

### Bearing preload

[edit]

Main article: Inline skate tuning § Bearing preload

Radial play results in uneven load Preload ensures even load distribution

Greater internal clearance in skate bearings helps prevent binding during side-loading maneuvers. However, it creates an uneven load distribution, with only the bottom ball and its neighbors supporting the skater’s weight. These form the load-bearing zone, while the other balls remain unloaded.[201] As balls rotate through the bearing, they briefly enter the load-bearing zone and endure stress beyond their design limits, accelerating wear.[202] At the top of rotation, balls lose contact due to clearance gaps, causing skidding, noise, energy loss, and more wear.[203] Uneven surfaces add shifting forces that, combined with the clearance, cause axle vibrations and worsen bearing misalignment.[182][201][204]

Bearing preload in inline skates refers to a specific type of axial load from clamping the inner race against a properly sized spacer using the axle bolt, pre-tensioning the bearing balls at an oblique contact angle. This reduces or removes internal clearance, keeping all balls engaged and evenly distributing the skater’s weight during wheel rotation.[199][201]

### Spacer length

[edit]

Main article: Inline skate tuning § Spacer length

Optimal spacer length

Preloading is especially useful in high-speed skating, like downhill racing, where it removes clearance gaps, reduces skidding, and minimizes axle displacement. This improves wheel assembly's rigidity, and increases skater's stability, precision and control.[199][205] By using a correctly sized spacer, the axle bolt can apply just enough tension to create slight negative internal clearance (around -0.01 mm), the optimal preload.[206][77] This delivers optimal load distribution and load-carrying capacity, minimizing wear and maximizing bearing lifespan.[205][202][207]

Short spacer binds wheels

Manufacturing imperfections often prevent spacers from perfectly matching the bearing abutment length.[P][194][45] If a spacer is too short, overtightening the axle bolt beyond the optimal preload tension can create excessive negative clearance, increasing friction and drastically reducing bearing lifespan. In severe cases, it may cause the bearing balls to bind and lock the wheels.[208][199][X] To address this, aluminum spacers are made in various lengths so skaters can match them to each wheel's exact dimensions.[Y]

Loose axle w. short spacer

To fix over-tension from short spacers, some skaters mistakenly loosen axle bolts, thinking it relieves excess preload. While this may let wheels spin freely, it causes the spacers and inner races to rattle and skid, producing clunking sounds. The inner races are no longer clamped, allowing bearing misalignment and excessive wear from side loads. This creates cycles of over-preload and under-tension, worsening damage. Omitting spacers entirely makes the issue more severe, potentially causing bearings to explode under strong side forces.[37]: 39–45 [180][209]

Slightly longer than optimal

If a perfectly sized spacer isn’t available, a slightly longer spacer is preferred over a shorter one to avoid over-tensioning and excessive bearing wear. While a longer spacer prevents preload by not letting the outer races brace against the bearing abutments, it still allows the inner races and spacer to be securely clamped. However, without preload, the outer races rely on press-fit friction, against bearing recesses, which may not hold under side loads. This can cause the outer races to shift, wear the hub’s bearing recess, and lead to lateral wheel movement and clicking sounds during skating.[194][193]

## Wheel setup

[edit]

Main article: Inline skate wheel setup

Wheel setup can refer to various aspects related to the selection and configuration of wheels. The total number of wheels and their diameter are often expressed in the form {number of wheels} x {wheel diameter in mm}. For instance, a common recreational skate setup is 4x80mm, which means four wheels, each with a diameter of 80 millimeters. Wheel arrangement patterns are typically named according to the profile formed by the wheels at their contact points with the ground. In a flat setup, all wheels maintain contact with the ground simultaneously. A classic rockered setup, by contrast, creates a banana-like profile along the bottom.[52][56]

### Flat setup

[edit]

Main article: Inline skate wheel setup § Flat setup

Flat wheel setup: 4x80mm

A flat setup is the most common wheel configuration used on inline skates. The majority of non-aggressive skates are sold with this arrangement. In a flat setup, all wheels make contact with the ground simultaneously when the skate is rolling on a level surface. While not as maneuverable as a rockered setup, a flat setup excels in disciplines that prioritize speed, stability, and long-distance efficiency. It is the standard choice for speed skaters and marathon skaters. Flat wheel setups are typically noted in the format {number of wheels} x {wheel diameter in mm}. For example, a common recreational setup is 4x80mm or simply 4x80, indicating four wheels, each with a diameter of 80 millimeters. [33]: 81–86 [75]: 20–21 [52][109][44]

### Rockered setup

[edit]

Main article: Inline skate wheel setup § Rockered setup

Rockering with frame hardware

A rockered setup, also called a full rockered setup or banana rocker, involves altering the wheel alignment to increase maneuverability. In a four-wheel inline skate, this typically means raising the bottom of the front and rear wheels by about 2 millimeters, so that only the two middle wheels touch the ground when standing on a flat surface. This setup mimics the profile of an ice skate blade, and is known as the "banana rocker" after its curved profile.[33]: 81–86 [147][43]: 28 [56][104]

70-70-70-70 rockered

A rockered setup generally produces the opposite skating characteristics of a flat setup. It offers much greater maneuverability and allows for quicker, easier turning. Freestyle slalom skaters and artistic inline skaters consider the rockered setup indispensable, as it enables gliding on just the front two wheels, the middle two wheels, or the rear two wheels, depending on the move. Having a short frame in combination with a full rocker is optimum for achieving the highest maneuverability when skating. However, this setup makes it more difficult to maintain stability at high speeds, since the skater cannot glide on all four wheels at once and is more prone to wheel wobbles when skating in a straight line.[75]: 20–21 [37]: 29–30 [78]

Rockering by sizing wheels: 76-80-80-76

A frame designed for a flat setup can still be converted into a rockered configuration by mounting smaller wheels at the front and rear. For example, a standard 4x80mm flat frame can become rockered by installing 76 mm wheels at the front and rear, while keeping 80 mm wheels in the middle. This customization creates a 2 mm height offset between the outer and middle wheels, mimicking the standard banana rocker profile. Skaters commonly notate mixed wheel sizes in millimeters, listed from the rear wheel to the front. The rockered configuration described above is typically written as 76-80-80-76.[75]: 20–21 [56]

### Natural rocker

[edit]

Main article: Inline skate wheel setup § Natural rocker

Severely worn (left) vs moderately worn (right)

Natural rockering can develop naturally on flat frames due to uneven wheel wear. Beginners often wear down front wheels faster, creating a natural hi-lo setup over time without needing different-sized wheels. Specific skating styles can also wear front and rear wheels more than the middle ones, forming a natural rocker. As wheels wear down, skaters can employ various rotation strategies to either restore a flat setup or enhance the rocker.[191][120][146] Although natural rockering usually produces less than the standard 2 mm height difference, many skaters prefer this subtle profile. Big-wheel urban skaters and Wizard skating advocates often use factory-tuned, pre-rockered frames designed to mimic this naturally worn rocker with new wheels of same size. Wizard even named its classic four-wheel frame NR, after "natural rocker".[210][78][63][211]

### Front rocker

[edit]

Main article: Inline skate wheel setup § Front rocker

Front rocker wheel setup: 80-80-80-76

A front rocker setup raises only the front wheel, while the remaining three wheels stay in a flat configuration. This design serves as a compromise between a full rockered setup and a flat setup. By gliding and striding primarily on the three rear wheels, the skater achieves greater top speed and improved stability, with less wheel wobble than in a full rockered setup. At the same time, the raised front wheel helps guide the skate over uneven terrain in urban environments.[212][75]: 20–21 [56]

### Hi-lo setup

[edit]

Main article: Inline skate wheel setup § Hi-lo setup

80-80-76-76 hi-lo frame

The hi-lo setup, also known as HiLo, is commonly found in hockey skates. Hi-lo is technically a flat setup, since all wheels maintain contact with the ground when the skate rests on a level surface. The term “hi-lo” refers not to the wheel contact profile, but to the vertical positioning of the boot. It raises the heel and lowers the toe, creating a heel-to-toe drop that encourages a natural forward lean. This forward flex promotes a more aggressive stance, enhances push-off power, and helps prevent backward falls. Unlike terms like “flat” or “rockered,” which describe how wheels touch the ground, “hi-lo” describes how the boot is angled forward.[212][56][38]: 57–59

Hi-lo hockey frame

This forward pitch can be achieved through a combination of frame design and wheel sizing. Some frames have built-in height offsets, resulting in a heel lift, common in hockey skates and standard on 165mm, 195mm, and Trinity mounts. However, this lift increases ride height, which can reduce stability. To counter this, hi-lo hockey frames use lower axle positions and smaller wheels toward the toe, keeping the front low while preserving forward lean and keeping ride height low. A typical hi-lo frame is annotated as 80-80-76-76, combining better power transfer during push-offs with improved control and stability.[213][55][109][66]: 311–314 [37]: 18–24

Hi-lo setups with smaller front wheels are often marketed as providing quicker acceleration, while the larger rear wheels are said to help with achieving and maintaining top speed. While it is true that smaller wheels accelerate more quickly and larger wheels maintain speed more easily, these performance traits are not the reason for the hi-lo configuration. The smaller front wheels are used out of necessity - to lower the toe of the boot and preserve the forward pitch - rather than for their isolated performance benefits alone. In practice, the smaller front wheels trade top speed for a lower and more stable ride.[213][63][Z]

By sizing wheels: 80-78-76-74 Hi-lo via rotation

Alternatively, a hi-lo setup can be created using a standard flat frame by fitting progressively smaller wheels from rear to front, with a typical hockey setup written as 80-78-76-74. This arrangement produces a total heel-to-toe height offset of 6 mm while maintaining full ground contact.[212][63] Instead of purchasing wheels in different diameters, a skater can gradually create a hi-lo setup through a hi-lo rotation strategy, by placing the most worn at the front and the least worn at the rear. This approach minimizes noticeable changes in ride height between rotations, offering a consistent skating feel over time.[191]

Many skaters casually refer to any mixed-size wheel configuration as a "rocker," which leads to the common but inaccurate use of the term "hi-lo rocker" to describe a standard hi-lo setup. This is a poor choice of words, as the hi-lo setup is a flat configuration. Some skaters also misuse "rocker" as a general synonym for "wheel setup", leading to additional confusion, such as referring to a flat setup as a "flat rocker".[56][AA][AB]

### Alternatives to hi-lo

[edit]

Smaller 2nd wheel Trinity mounting

Main article: Inline skate wheel setup § Alternatives to hi-lo

Hi-lo is not the only approach to achieving a pitched boot with a low ride height. Speed skaters seek forward flex and low center of gravity while using larger wheels, which raise ride height. To counter this, some 165mm frames shift the second axle or use a smaller second wheel to lower the front.[70][71] Similarly, the ROCKIN' MIX4 100/90 frame uses smaller middle wheels and adjusted axle positions to form a 100-90-90-100 setup, keeping the boot closer to the ground.[120][78]

The Trinity system takes a different approach, with two front mounting points placed off-center, clearing space above the front wheels so they can sit closer to the boot. This allows setups like the Endless Trinity 90 with 3x110mm wheels to position the toe just 110 mm above the ground.[109][98] Wizard frames, using the UFS standard, achieve forward pitch by sloping the frame’s mounting surface, despite using equal-sized wheels. However, UFS-based setups usually result in a higher ride height compared to Trinity.[78][211]

### Forward lean with a rocker

[edit]

Main article: Inline skate wheel setup § Forward lean with a rocker

Wizard NR with Natural Rocker

A new variation of rockered skating emerged in the early 2010s, led by a new generation of aggressive skaters who rediscovered the benefits of rockered setups, this time using larger wheels on longer frames.[78][52] Wizard Skating became a key influence. Its frames are made for flat UFS boots but feature a sloped mounting surface that creates a slight forward lean, similar to a hi-lo flat setup. The Wizard NR series is pre-rockered with a mild banana rocker called the Natural Rocker. The NR90 model uses four equal-sized wheels in a 90-90-90-90 rockered layout.[211]

Ninja NN 90 with V.m Rocker

Similarly, the Endless Blading 90 frame is pre-rockered to support four 90 mm wheels. This setup, branded as the Balanced Rocker, is another mild version of the banana rocker. The frame uses the 165mm mounting standard, with a built-in forward lean.[214] Another example is the Ninja NN 90 frame from NN Skates, which also features a pre-rockered design. It introduces NN Skates' proprietary V.m Rocker, short for "modified V Rocker". The 165mm and Trinity versions come with built-in forward lean.[215]

Artificially pivoted view

All of these pre-rockered frames are variations of the full rockered setup, combined with built-in forward lean. However, they are sometimes marketed using simplified illustrations that "horizon-correct" the top surface of the frame, showing the boot level and the skate pivoting primarily on the third wheel. This conceptual stance is often described as a "V-shaped" wheel contact profile, a "V rocker," or a "3rd-wheel down" configuration. In practice, however, skaters do not glide on a single wheel. Instead, they roll on two wheels at a time, such as the 2nd and 3rd, where the boot naturally tilts forward like a hi-lo setup.[104][78][216][211]

Some skaters therefore refer to this combination of forward pitch and rocker as the "hi-lo rocker" or full hi-lo rocker. However, these terms can be confusing, especially since "hi-lo rocker" is also used colloquially to describe standard hi-lo setups. At present, there is no consistent term for this combination of banana rocker and forward lean in a pre-rockered frame.[56][191][AA][AB]

### Anti-rocker setup

[edit]

Main article: Inline skate wheel setup § Anti-rocker setup

Typical anti-rocker setup

The anti-rocker setup is the most widely used wheel configuration among aggressive skaters. It gets its name from being the opposite of a rockered setup. In an anti-rocker configuration, the two middle wheels are raised off the ground, leaving only the front and rear wheels to make contact on flat surfaces. The middle wheels are typically spaced farther apart than in standard four-wheel setups, and are often made of harder materials with minimal grip. These hard wheels are commonly referred to as grindwheels, antirockers, or anti-rocker wheels.[56][57] They are designed for one task alone: to make grinding on ledges and rails easier. [53][217]

### Freestyle setup

[edit]

Freestyle frame

Main article: Inline skate wheel setup § Freestyle setup

The freestyle setup is another wheel configuration favored by aggressive skaters. Despite the name, it is unrelated to freestyle slalom around cones or freestyle skating on flat ground free of street obstacles. This setup features only two outer wheels, with the middle portion of the frame replaced by solid material that resembles an extended H-block, optimized for grinding.[53][57]

Freestyle via juice blocks

Fifty-50's Balance Frame introduced a convertible design that can use either grindwheels or juice blocks in the center. When juice blocks are installed as grind blocks, they fill the space between the frame walls, extending the H-block to form a smooth, solid grinding surface. This setup transforms the Balance Frame into a freestyle frame.[218][57]

## See also

[edit]

* Roller skates \- Inline skates are technically a type of roller skate, but roller skates now exclusively refer to quad skates.
* Ice skates \- Inline skates traces back to the origin of ice skates, as a way to glide on non-ice surfaces, with wheels.
* Inline skating \- Different types of inline skates reflect needs specific to different inline skating disciplines.
* Roller sports \- Inline skating is one of many sports that use human-powered roller vehicles, in this case, inline skates.

## Notes

[edit]

1. ^ Vandervell and Witham's 1880 book on figure skating not only covered ice skating, but dedicated a full chapter 5, named "Roller-Skating", to Plimpton's roller skates and to equivalencies of outside edges and club figures between his roller skates and ice skates. By 1880, the term "roller skates" were synonymous with Plimpton skates.[14]: 70–99
2. ^ a b See ads for the Chicago Roller-Blade in the 1965 Fall & Winter Montgomery Ward catalog, page 1082, archived here, and in the 1965 Spring & Summer Catalog, page 846, archived here.
3. ^ a b See ad for Super Sport Skates endorsed by Ralph Backstrom in "Faceoff" 73 / 74 season by World Hockey Association.[23] Also see archived pictures one, two, three and four, from an antique listing.
4. ^ a b Inline skating adopts the terms "outside edge" and "inside edge" from ice skating, even though inline wheels lack the sharp dual edges of ice blades. The outside edge refers to the side of the wheel facing away from the skater's body, while the inside edge is the side facing inward.[33]: 27–31, 41–42, 49–52
5. ^ See catalog pages from various makers and resellers in Jan 2025, for wildly different ways they classify recreational, fitness and cross-training skates: Rollerblade (archived), Powerslide (archived), Roces (archived), K2 (archived), and Inline Warehouse (archived). See Ivo Vegter's Youtube video on the classifications of recreational skates.[41]
6. ^ Page 77 of Skaters magazine from 1990 featured an ad by Rollerblade on "Aggro Culture", an alternative term for aggressive inline skating. It urged readers to send $4 for an "Aggro Culture Poster". It's not clear whether Rollerblade promoted this term beyond 1990.[44]
7. ^ See archived product pages from Rollerblade: 2011 page showing a selection of Rollerblade "Street Skates", 2016 selection, and 2024 selection.
8. ^ a b See inline hockey skates made by ice hockey manufacturers, archived here: CCM Super Tacks 9370R, Bauer Vapor 3X Pro, Mission Inhaler WM02, True TF9 Roller Hockey Skate, and Marsblade R1 Kraft Crew.
9. ^ Refer to this video showing the production process of a Bauer hockey skate (both ice and inline), corresponding to the US patent 7,316,083. See FIG. 9: an exploded view showing components used in the construction of a traditional hockey skate in the 2010s.[61][60]
10. ^ See US patent 7,039,977 filed by Mission Hockey in 2003, showing the same hockey boot construction, mounted on an ice blade (FIG. 1), and on a wheeled frame (FIG. 2).[62]
11. ^ See background section discussion on why hard boots with hinged cuff and thick liners do not work to either ice hockey or roller hockey, in US patent 7,039,977 from Bauer/Mission.[62]
12. ^ Refer to this video showing the production process of a speed skate with a custom-molded carbon-fiber shell (both ice and inline).[69]
13. ^ The loosely defined terms "frame height," "deck height," and "ride height" are usually absent from the technical specifications of skates or frames. However, they are frequently used in reviews and buying guides for comparison. In the following articles, the distance from the bottom of a boot (i.e., the sole) to the ground is variously referred to as frame height, deck height, and ride height: Skating Magic archive, Inline Warehouse archive, Cadomotus archive, Loco Skates archive 1, and Loco Skates archive 2. Similarly, the distance from the top of a mount (i.e., roughly the sole) to the center of a wheel axle is described as deck height and ride height in these articles: Atom Skates archive and Loco Skates archive 3. Only in rare instances, such as on this product page, does "frame height" actually refer to the physical measurement of the frame itself.
14. ^ a b c Brennan Olson's patent application filed in 1987 described key innovations in the 1988 Lightning skate: a single-piece plastic frame with reinforcement bridges, toggleable inserts for mounting hole for rockering (named axle aperture plug in the specification), and wheel hubs each with an interlock rim (named outer annular ring 16P) over which polyurethane is molded to reduce wheel deformation and heat buildup.[103]
15. ^ See pictures of the new generation of early Rollerblade skates with heel brakes, from Vintage Minnesota Hockey: picture, picture, picture and picture, archived here, here, here and here. These have a refined version of the adjustable frame from the Ultimate Street Skate, and a similar hard boot. These skates witnessed the transition of Scott Olson's company from "Ole's Innovative Sports", to "North American Sports Training Corp.", and finally to "Rollerblade", as attested by marketing materials.[105]
16. ^ a b c d Ricardo Lino toured the factory floor of Aend Industries, a polyurethane wheel factory, with co-owner Tony Gabriel. Discussions cover all aspects of wheel-making, including history of the company, co-ownership with Neil Piper, machines bought from Tom Peterson, brands they OEM for, injection molding of hubs (cores), trimming of hubs, polyurethane coloring, urethane bonding, dual-density urethane, hardness vs grippiness, hardness vs profile, heating of urethane before pouring, casting urethane into molds, baking after casting, cutting/shaving wheels to final profile, quality control, washing, printing, and packaging.[131]
17. ^ a b See table in the Gallagher article showing polyurethane compounds with varying hardness from 60A to 95A and varying rebound values (Bayshore Resilience) from 25% to 60%, with no correlations. A YouTube video (archived) from the article demonstrates "polyurethane resilience" tests (yet another name for Bayshore Resilience) showing two balls with the same hardness, but opposite rebound values. At 0:41, an inline skate wheel with high rebound was shown bouncing off the floor.[132]
18. ^ Roller Derby made clay composition wheels in the 1960s for their "sidewalk surfboards" (skateboards).[134][135] The same wheels were used in their Royal Sidewalk line of roller skates as late as 1974 (archived catalog page). By 1978, however, the same Royal Sidewalk line adopted polyurethane wheels under the brand Fireball (archived catalog page). See archived entry and images of this Etsy listing showing a pair of Royal Sidewalk skates with these clay wheels: listing page, image 1, and image 2.
19. ^ a b Page 79 of Skaters magazine from 1990 features a Kryptonics ad showing the cross section of a Kryptonics wheel with polyurethane molded over a hub through holes in its interlock rim. Page 77 of the same 1990 Skaters magazine features a Rollerblade ad stating that Kryptonics is the official wheel supplier for rollerblade skates.[44]
20. ^ Brennan Olson's 1987 patent described wheels with polyurethane poured over a hub with an interlock rim (outer rigid ring 46), and showed drawings of the same.[103]
21. ^ a b Consult sections on bearings, spacers, wheel assembly, and bearing preloading from the Big Wheel article.[77]
22. ^ SKF’s 1,152-page rolling bearings catalog lists a limiting speed of 38,000 RPM for its Explorer-class 608-2Z bearings (pages 135 and 262). These bearings meet ISO 492 Class 6 precision tolerances, which are equivalent to ABEC 3, as noted on pages 7, 36, 248, and 250.[164]
23. ^ a b c d e Bearing shielding and sealing are designated by suffixes that vary between manufacturers. These designations are typically published in technical handbooks and catalogs.[178] One NTN suffix conversion table can be found on page 178 of the Bearing Nomenclature Guide by BDS.[179] There is no industry-wide standard that clearly defines when a "shield" becomes a "seal," nor where non-contact shields end and light-contact or non-contact seals begin. Likewise, the skating industry adopts suffixes inspired by those used in the bearing industry, but does not apply them consistently across brands.[162] Generally, removable metal gap shields are labeled with the suffix "Z" in a fairly uniform way. See Rollerblade SG9 bearings (archived). C-ring mounted metal gap shields, popularized by TWINCAM, are rarely marked with a distinct suffix, but when they are, they follow the "ZS" convention used by SKF.[163][164] The skating industry’s use of the "RS" suffix typically refers to a non-contact NBR shield that physically resembles the RS/2RS contact lip seals used by INA/Schaeffler, but instead leaves a narrow gap, similar to SKF’s non-contact "RZ" shields.[177][180][181][164] The "RSL" suffix in skating refers to a full-contact labyrinth seal, comparable to SKF’s own RSL low-friction seals, except that SKF RSL leaves small gaps while bending the contamination path.[180][164]
24. ^ See charts from NASA research and bearing manufacturers that illustrate bearing life as a function of internal clearance in radial ball bearings. At approximately -0.01 mm clearance (representing optimal preload), bearing life reaches 100%. If under-tensioned (i.e. the axle bolt is not fully tightened), bearing life drops by nearly half with a positive clearance gap of 0.05 mm. Conversely, if over-tensioned (i.e. using a spacer that is too short), an additional negative clearance of just -0.01 mm can reduce bearing life to 20%.[202][207]
25. ^ A Wicked spacer kit (archived) includes assorted spacers of these lengths: 9.90 mm, 9.95 mm, 10.00 mm 10.05 mm, 10.10 mm, 10.15 mm, (10.20 mm), 10.25 mm, 10.30 mm, 10.35 mm.
26. ^ Misleading marketing is common, where hi-lo frames are advertised as offering quicker acceleration due to the smaller front wheels and higher top speeds thanks to the larger rear wheels. These claims often ignore the primary design purpose: creating forward lean by allowing the front of the boot to sit lower, which enhances forward pitch and skating posture. See for instance, Hi-lo Frames from Powerslide (archived here), and A Guide to Roller Hockey Wheels from Willies (archived here). If these marketing claims were entirely accurate, we would expect to see hockey frames with extremely small front wheels (e.g. 50 mm) and oversized rear wheels (e.g. 110 mm) to further enhance acceleration and top speed, without any design features to leverage vacated front space to pitch the boot forward. In reality, such frames do not exist.
27. ^ a b Even professional skaters occasionally write "hi-lo rocker" when they mean "hi-lo flat". See Thierstein, for instance. Redditors often write "hi-lo rocker", using the word "rocker" for any mixed-size wheel configuration. See this, this and this, for instance.
28. ^ a b Even professional skaters occasionally write "flat rocker" when they mean "flat setup". See This Is Soul, Big Wheel Blading, and Naomi's book, for instance.[75]: 20–21

## References

[edit]

1. ^ "The night of a thousand wheels". BBC News. 20 July 2002. Archived from the original on 2008-06-24.
2. ^ "Pari Roller – La Friday Night Fever !". Archived from the original on 30 January 2008.
3. ^ "Clubs and Leagues: Group Skates". New York City Inline Skating Guide. Archived from the original on 2022-12-03.
4. ^ "NYC Skating Info Links". Empire Skate Club of New York. Archived from the original on 2022-07-09.
5. ^ "The First Roller Skates". National Museum of Roller Skating Audio Tour. Archived from the original on 2024-11-25.
6. ^ "Charles-Louis Petibled : le premier brevet de l'histoire du patin à roulettes". Le Roller en Ligne. 30 March 2019. Archived from the original on 2024-01-29.
7. ^ a b Turner, James; Zaidman, Michael (1997). The History of Roller Skating. Lincoln, Nebraska: National Museum of Roller Skating. ISBN 0965819205. Illustrated with museum collections and archives.
8. ^ "The History of Skating from 1760 till Today". OLS Online Skating. 12 November 2023. Archived from the original on 2024-11-28.
9. ^ "Historical Notes on Roller Skates No. 2". The Engineer. Vol. 41\. London: Morgan-Grampian. 1876-02-11. pp. 102–103. Retrieved 2024-11-30.
10. ^ "Historical Notes on Roller Skates No. 3". The Engineer. Vol. 41\. London: Morgan-Grampian. 1876-02-18. pp. 121–122. Retrieved 2024-11-30.
11. ^ US 37305, Plimpton, James, "Improvement in skates", published 1863-01-06
12. ^ "The Father of the Modern Roller Skating". National Museum of Roller Skating Audio Tour. Archived from the original on 2024-11-28.
13. ^ "The Victorian craze that sparked a mini-sexual revolution". BBC News. 6 April 2015. Archived from the original on 2024-11-28.
14. ^ Vandervell, H.E.; Witham, T. Maxwell (1880). A System of Figure-skating: Being the Theory and Practice of the Art as Developed in England with a Glance at Its Origin and History. London: Horace Cox. pp. 4–7. Retrieved 2024-11-24.
15. ^ Dowson, Duncan; Hamrock, Bernard J. (1981). "History of Ball Bearings" (PDF). NTRS - NASA Technical Reports Server. Archived (PDF) from the original on 2024-11-30.
16. ^ US 308990, Richardson, Levant Marvin, "Roller-Skate", published 1884-12-09, issued 1884-12-09
17. ^ "The History of Inline Skating". National Museum of Roller Skating. Archived from the original on 2019-04-10.
18. ^ Burnson, Robert. "The Illustrated History of Inline Skate Design At the U.S. Patent Office: Siffert's Jet Skate, 1938". The Inline Planet. Archived from the original on 2021-12-07.
19. ^ a b US 3287023, Ware, Gordon K, "Roller skate", published 1966-11-22, issued 1966-11-22
20. ^ a b c d Paul A. Dunn and Sharry Beck Paprocki (June–July 1990). "Joseph Shevelson interviewed by Paul A. Dunn and Sharry Beck Paprocki on the Golden Days of Skating" (PDF). Skaters. Vol. 1, no. 1: Premier Issue. Mt. Morris, Ill.: CFW Enterprises, Inc. pp. 12–18\. Archived from the original (PDF) on 2024-06-19. Retrieved 2024-12-20.
21. ^ a b c US 3880441, Silver, Morris L, "Tandem roller hockey skate", published 1975-04-29, issued 1975-04-29
22. ^ Ross, Emily; Holland, Angus (2006). "Rollerblade - Live your product". 100 Great Businesses and the Minds Behind Them. Naperville, Illinois: Sourcebooks, Inc. pp. 151–155\. ISBN 978-1402206313. Retrieved 2024-12-20.
23. ^ "Ad for Super Sport Skates by Super Skate Inc. sponsored by Ralph Backstrom". Faceoff 73 / 74 season. World Hockey Association. 1973. Archived from the original on 18 December 2024. Retrieved 2024-12-21.
24. ^ "The early years - 1957 to 1963". Lange - The History of an All-American Brand. Archived from the original on 2023-11-24. Retrieved 2024-12-27.
25. ^ "From racing glory to bleeding "Flo" - 1970 to 1973". Lange - The History of an All-American Brand. 2009-02-01. Archived from the original on 2023-11-24. Retrieved 2024-12-27.
26. ^ "The Roller Renaissance: Forgiving, quiet urethane wheels and new suspension tricks have put a great sport back on its feet". Popular Mechanics. Vol. 151, no. 6\. Chicago: Popular Mechanics Company. June 1979. p. 94. Retrieved 2024-12-20.
27. ^ a b c d e f g Fried-Cassorla, Albert (1995). In-line Skating: The Ultimate How-to Guide. Fried-Cassorla authored a 1976 book on skateboarding before this 1995 book on inline skating: The Skateboarder's Bibble: technique, equipment, stunts, terms, etc. California: Prima Publishing. ISBN 1559586486. Archived from the original on 2011-12-02. Retrieved 2025-01-11.
28. ^ Hahn, Steve (2012-02-06). Steve Hahn interviews Scott Olson ( Rollerblade Founder ) (video). Steven Hahn – via YouTube. Refer to the video transcript for this long interview, a part of the "Hockey in the Park" Series.
29. ^ a b "Mind in motion: The MIA's Leonardo show traces Scott Olson's inventive impulse". Minneapolis Institute of Art. Archived from the original on 2024-02-27.
30. ^ "A Business That's On a Roll". Star Tribune (Minneapolis). Minneapolis. 1985-11-17. Retrieved 2024-12-23.
31. ^ Paula Schroeder (host) (1995-07-31). Voices of Minnesota: Interview with Scott Olson (Part 1 of 3) (audio). Minnesota: Minnesota Public Radio. Transcript 1/3 in PDF (PDF). Retrieved 2024-12-25.
32. ^ Paula Schroeder (host) (1995-07-31). Voices of Minnesota: Interview with Scott Olson (Part 2 of 3) (audio). Minnesota: Minnesota Public Radio. Transcript 2/3 in PDF (PDF). Retrieved 2024-12-25.
33. ^ a b c d e f g h i j Middlebrook, Chris, ed. (1985). Rollerblades: Dryland Training for Ice Hockey. Chapters by Randy Gregg, Jack Blatherwick, Laura Stamm, Brad Buetow, Scott Olson, Brennan Olson. Minneapolis, Minn.: Ole's Innovative Sports. Archived from the original on 2025-01-08. Retrieved 2025-01-08.
34. ^ "Inventor of the Week Archive: Scott & Brennan Olson (spelling corrected per rowbike.com -ed.)". MIT School of Engineering. August 1997. Archived from the original on 2003-03-02. Retrieved 2007-02-25.
35. ^ Peippo, Kathleen; Rhodes, Nelson (2000). "Rollerblade, Inc.". International Directory of Company Histories. Vol. 34\. Detroit: St. James Press. pp. 388–392. Retrieved 2024-12-23.
36. ^ "A Craze May Outsprint Its Creator". New York Times. New York. 1990-08-07. Archived from the original on 2014-03-21. Retrieved 2024-12-22.
37. ^ a b c d e f g h i j k l m n o p q r s t u v w x y z aa ab ac ad ae af ag ah ai aj ak Powell, Mark; Svensson, John (1998). In-line Skating. Champaign, Ill.: Human Kinetics. ISBN 0880116595. Retrieved 2024-12-23.
38. ^ a b c d e f g h i j Miller, Liz (2003). Get Rolling: The Beginner's Guide to In-line Skating (3rd ed.). California: Get Rolling Books. ISBN 0963219634. Retrieved 2025-01-02.
39. ^ Vegter, Ivo (2022-03-13). Everything About Skate Tools (video). This is Soul – via YouTube. See video transcript on all types of skate tools with hex, Torx and other wrench tips for removing wheel, axels, frames and bearings.
40. ^ a b c d e f Gutman, Bill; Frederick, Shawn (2004). Catching Air: the excitement and daring of individual action sports - snowboarding, skateboarding, BMX biking, in-line skating. New York: Citadel Press. ISBN 0806525401. Retrieved 2025-01-04.
41. ^ a b c d e f g Vegter, Ivo (2024-12-09). "The Strange History Behind Inline Skating // Many Names" (video). thisissoul.com. See video transcript on history on different types of inline skates and skating, including naming, relationships and differences: Rollerblade, Bladers, skeeler, Partines, Roller Freestyle, Recreational inline, soft boot, hard boot, Slalom inline, Freestyle inline, Urban inline, Flow inline, Tri-Skates, and Aggressive inline. The history intro also discusses quad skates, skateboarding and their shared history with inline skating, including wheels, axles and ISO 608 bearings. This is Soul.
42. ^ a b c d e f g Knoll, Matthias; Pfitzner, Jürgen (2018-07-20). Inline skate differences - hard boot, soft boot, hybrid ?! (video). Discourses on hard boot vs. soft boot with exoskeleton vs. hybrid boot with endoskeleton. Powerslide – via YouTube.
43. ^ a b c d e f g h Joyner, Stephen Christopher (1995). In-line Roller Hockey: The Official Guide and Resource Book. Chicago: Contemporary Books. ISBN 0809234483. Retrieved 2025-01-01.
44. ^ a b c d e f Chris Morris (June–July 1990). "In-Lines: Getting Started - Tips for the beginner" (PDF). Skaters. Vol. 1, no. 1: Premier Issue. Mt. Morris, Ill.: CFW Enterprises, Inc. pp. 32–36\. Archived from the original (PDF) on 2024-06-19. Retrieved 2024-12-20.
45. ^ a b c d e f g h i j k l m "Physics of the inline skate wheel". Le Roller en Ligne. Archived from the original on 2025-03-22. Retrieved 2025-03-27.
46. ^ a b c d e f g US 5922151, Piper, Neal & Peterson, Tom, "Polyurethane skate wheel with shaped foam core", published 1999-07-13, issued 1999-07-13, assigned to Hyper Corp (Hyper Wheels)
47. ^ a b Feineman, Neil (1991). Wheel Excitement. New York: Hearst Books. ISBN 0688108148. Retrieved 2024-12-23.
48. ^ a b c d e f g h Vegter, Ivo (2021-06-27). "Hardboot VS Softboot" (video). thisissoul.com. See video transcript on how recreational skates range from inexpensive soft boots with exoskeletons, to mid-end hard boots, to high-end (hybrid) soft boots with endoskeleton - and varied levels of ankle support. This is Soul.
49. ^ a b Pat Parnell (June–July 1990). "Quads vs. In-Lines" (PDF). Skaters. Vol. 1, no. 1: Premier Issue. Mt. Morris, Ill.: CFW Enterprises, Inc. pp. 37–42\. Archived from the original (PDF) on 2024-06-19. Retrieved 2024-12-20.
50. ^ "How to Inline Skate". Xinhai Dude. 2022-04-24. Archived from the original on 2024-11-18. Retrieved 2025-01-03.
51. ^ a b c d "How to Choose Urban Inline Skates". Inline Warehouse. Archived from the original on 2025-01-26. Retrieved 2025-01-26.
52. ^ a b c d e f g h i j Welch, Jan (21 June 2023). "Demystifying Inline Skating Disciplines: A Complete Guide". Big Wheel Blading. Archived from the original on 2024-12-13. Retrieved 2025-01-04.
53. ^ a b c d "How aggressive inline skates are built". Bladeville. Archived from the original on 2025-01-12. Retrieved 2025-01-12.
54. ^ a b What is UFS? Past, Present and Future of frame mounting (video). See video transcript on discussions on origin of not just UFS, but also of original rivet mounts in Rollerblade TRS, and K2 Fatty. Aggressive makers rallied around the Salomon boot with a flat sole and created UFS standard. Back to Blading. 2018-10-25. Archived from the original on 2025-02-16. Retrieved 2025-05-04 – via YouTube.`{{cite AV media}}`: CS1 maint: others in cite AV media (notes) (link)
55. ^ a b c d e f g h i j k l "Everything about Frames". This Is Soul. 4 January 2022. Archived from the original on 2025-01-15. Retrieved 2025-01-16.
56. ^ a b c d e f g h i j Thierstein, Markus. "Inline Skating Knowledge: Rockering". Skating Thierstein. Archived from the original on 2019-04-16. Retrieved 2025-01-20.
57. ^ a b c d "Everything about Grindwheels". This Is Soul. 29 May 2023. Archived from the original on 2025-01-22. Retrieved 2025-01-22.
58. ^ "What's in a name? Describing Skating to the Masses". Be-Mag. 2023-01-29. Archived from the original on 2024-09-15. Retrieved 2025-01-13.
59. ^ Irwin, Dawn (2000). Superguides: Inline Skating. London: DK Pub. ISBN 0789465426. Retrieved 2024-12-29. p. 11: "A picture of 1981 Ultimate Hockey Skate is shown under the headline: Modern inline skate"
60. ^ a b c US 7316083, Labonté, Ivan, "Footwear having an outer shell of foam", published 2005-09-29, issued 2008-01-08, assigned to Bauer Hockey LLC
61. ^ a b "Ice Skates: How It's Made (Hockey Skates)" (video). discoveryuk.com. Discovery UK. 2020-06-05. Video shows the production process of a traditional hockey skate, with a boot that is fitted to either an ice blade or an inline wheel frame.
62. ^ a b c US 7039977, Wilder, Thomas V., "Contoured skate boot", published 2004-05-06, issued 2006-05-09, assigned to Mission Itech Hockey Inc and Bauer Hockey LLC
63. ^ a b c d e All The Inline Skating Setups I've Tried So Far - My Setup Journey (video). See transcript for discussions on inline skate setups with different combinations of boots, frames, wheels and wheel setups. Rerolling Inline. 2023-04-18. Archived from the original on 2025-04-27. Retrieved 2025-05-04 – via YouTube.`{{cite AV media}}`: CS1 maint: others in cite AV media (notes) (link)
64. ^ "The History of Hockey Skates, Part II: The Rise of Hockey-specific Skates". Pure Hockey / Hockey Resource Center. Archived from the original on 2025-01-17. Retrieved 2025-01-17. See discussion on how Lange hard boots did not fare well in ice hockey.
65. ^ US 8329083, Jou, Wern-Shiarng, "Method of making a lasted skate boot", published 2010-11-04, issued 2012-12-11, assigned to Bauer Hockey LLC
66. ^ a b c d e f g h i j Publow, Barry (1999). Speed on Skates: a complete technique, training and racing guide for in-line and ice skaters. Champaign, Ill.: Human Kinetics. ISBN 0880117214. Retrieved 2025-01-05.
67. ^ "World Speed Records - updated 2023". World Skate. Archived from the original on 2025-01-24. Retrieved 2025-01-24.
68. ^ a b c "Buying Speed Skates". SkatePro. Archived from the original on 2025-01-25. Retrieved 2025-01-25.
69. ^ "How It's Made: Speed Skates" (video). discoveryplus.com. Discovery Plus. 2022-04-14. Video shows the production process of custom-molded speed skates, with boots that could be fitted to either an ice blade or an inline wheel frame.
70. ^ a b c "Mounting your inline boot on an ice blade? Why that doesn't fit (unfortunately)". Cádomotus. discusses 165mm and 195mm mounting standards, and explains why a 195mm boot will not fit a standard ice blade tailored to average heel-to-ball distances. 2020-12-29. Archived from the original on 2025-03-01. Retrieved 2025-03-01.`{{cite web}}`: CS1 maint: others (link)
71. ^ a b c d "Inline Skate Frames". Bladeville. Archived from the original on 2025-02-17. Retrieved 2025-02-17. Widen browser width for desktop rendering mode, to see descriptions of frame standards: 165mm, 195mm, UFS and Trinity.
72. ^ Vegter, Ivo (2019-09-29). "Freestyle vs Aggressive vs Street skating // Terminology" (video). thisissoul.com. Discussion on freestyle inline skating, aggressive inline skating, and their relationship to BMX biking and skateboarding. This video explains how various disciplines acquired their names. It also clarifies labels under which skates suitable for these disciplines are marketed. This is Soul.
73. ^ "IFSA Freestyle Slalom Rules". International Freestyle Skaters Association. Archived from the original on 2025-02-05. Retrieved 2025-02-05.
74. ^ "World Skate Inline Freestyle Regulation". World Skate. Archived from the original on 2024-07-18. Retrieved 2025-02-05.
75. ^ a b c d e f g h i j k l m Grigg, Naomi (2014). The Art of Falling: Freestyle Slalom Skating. San Francisco: Patson Media. ISBN 9780692227374.
76. ^ a b c "Inline Skate Frame Buying Guide". Inline Warehouse. Archived from the original on 2025-02-05. Retrieved 2025-02-05.
77. ^ a b c d "Reign Ares as big-wheel skates for urban marathons". Xinhai Dude. 2024-11-16. Archived from the original on 2025-03-02. Retrieved 2025-03-02.
78. ^ a b c d e f g h "Rockering in Wizard Frames & Rest of the Pack". Bladeville. Archived from the original on 2025-02-05. Retrieved 2025-02-05.
79. ^ a b c "What is Inline Skating – Inline Skating in Brief". SkaMiDan – Skating School & Skateshop. 16 November 2023. Archived from the original on 2025-01-09. Retrieved 2025-02-09.
80. ^ Luhn, Andy (2002-07-23). "K2 Corporation (K2 Sports) — a History". HistoryLink.org. Archived from the original on 2024-09-14. Retrieved 2025-02-18.
81. ^ Gorski, Chris. "Skate-O-Pedia / Articles / Aggressive Skates". Inlineskates.com. Archived from the original on 2021-10-18. Retrieved 2025-02-09.
82. ^ a b "What are Carbon-fiber Inline Skates?". Xinhai Dude. 2024-10-21. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
83. ^ "Softboots - not that bad, actually!". Bladeville. 2022-04-02. Archived from the original on 2023-05-25. Retrieved 2025-02-01.
84. ^ Lino, Ricardo (2017-08-02). Soft boot vs hard boot - skates vlog132 (video) – via YouTube. See video transcript.
85. ^ "About VH Hockey". VH Hockey. Archived from the original on 2015-02-25. Retrieved 2025-01-18.
86. ^ "Easton Synergy 1300C Hockey Skates ('05 Model)- Senior". Perani's Hockey World. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
87. ^ "Easton Synergy Skates Break-In?". Hockey Forum. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
88. ^ "What's New: Recreation". Popular Science. Vol. 270, no. 1\. January 2007. p. 26. Retrieved 2025-01-18.
89. ^ "Easton Synergy 1500C IHS Hockey Skates". Sideline Swap. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
90. ^ a b O'Connor, Dana (2023-09-07). "Ep 21 Scott Van Horne - True - Legendary Skate Builder - Got Hockey" (video). Got Hockey. See transcript for this 45 minute chat with Scott Van Horne.
91. ^ "True Temper Sports Acquires VH Footwear: 2016-09-22". Hockey World Blog. 22 November 2016. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
92. ^ True Hockey Skate Factory Tour (video). Inline Warehouse. 2023-07-26 – via YouTube. Scott Van Horne showing the manufacturing process of a True hockey skate with a monocoque shell, as specified in VH Footware's US patent 9,656,153.
93. ^ a b "TRUE TF9 Senior Roller Hockey Skates". The Hockey Shop. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
94. ^ "True Pro Custom Roller Hockey Skate Senior". Coast to Coast Hockey Shop. Archived from the original on 2025-01-19. Retrieved 2025-01-19.
95. ^ a b c d "Powerslide Frames Guide" (PDF). Powerslide. Archived (PDF) from the original on 2024-05-28. Retrieved 2025-03-08.
96. ^ a b "Inline Skate Frame Buying Guide". Skating Magic. 2021-07-31. Archived from the original on 2025-03-05. Retrieved 2025-03-05.
97. ^ a b "Frame Mounting for Inline Skates - Everything You Need To Know". Loco Skates. 2024-05-30. Archived from the original on 2025-01-20. Retrieved 2025-03-05.
98. ^ a b c Lino, Ricardo (2017-11-07). Why Trinity? The latest generation inline skates frame system // vlog 182 (video) – via YouTube. See video transcript.
99. ^ "Which skate frame for which use?". Le Roller en Ligne. 3 November 2010. Archived from the original on 2025-02-15. Retrieved 2025-02-15.
100. ^ "The manufacturing processes of skate frames". Le Roller en Ligne. 23 November 2007. Archived from the original on 2025-02-15. Retrieved 2025-02-15.
101. ^ "Anatomy of a skate frame". Le Roller en Ligne. 6 December 2007. Archived from the original on 2025-02-15. Retrieved 2025-02-15.
102. ^ "Which material for your skate frames: Magnesium or aluminum?". Le Roller en Ligne. 25 January 2011. Archived from the original on 2025-02-15. Retrieved 2025-02-15.
103. ^ a b c d e f g US 4909523, Olson, Brennan J., "In-line roller skate with frame", published 1990-03-20, issued 1990-03-20, assigned to Rollerblade Inc
104. ^ a b c "The Geometry of Inline Skate Rocker Designs". Endless Blading. 11 July 2020. Archived from the original on 2025-02-16. Retrieved 2025-02-16.
105. ^ "Minnesota In-Line Hockey and History of In-Line Skates". Vintage Minnesota Hockey. Archived from the original on 2024-07-15. Retrieved 2024-12-26. A picture gallery at the bottom of the page shows rare historical images of early Rollerblade prototypes and products including the Ultimate Street Skate.
106. ^ "Interview with Alexander Bont, owner of the Australian Brand". Le Roller en Ligne. 2015-07-22. Archived from the original on 2025-02-17. Retrieved 2025-02-17.
107. ^ "Glossary of terms in rollerblading". Bladeville. Archived from the original on 2025-02-17. Retrieved 2025-02-17.
108. ^ "Bont - About Us - Who we are". Bont. Archived from the original on 2024-11-26. Retrieved 2025-02-16.
109. ^ a b c d e "Trinity system – incoming revolution". Że co, przepraszam?!. Interview with Powerslide on the upcoming Trinity mounting system (2016) with respect to popular 165mm and 195mm mounting systems. 2016-01-15. Archived from the original on 2025-02-17. Retrieved 2025-02-17.`{{cite web}}`: CS1 maint: others (link)
110. ^ a b Briand, Pascal (2021-08-18). Pit Stop - Discover the different mounting systems of inline skates (video). Covers Trinity, 195mm, UFS, 165mm, and riveted mounting systems. Powerslide – via YouTube.
111. ^ "195 Mounting". Powerslide. Archived from the original on 2025-02-17. Retrieved 2025-02-17.
112. ^ "Is 2015 the comeback year of 165mm mounting?". Le Roller en Ligne. 2015-04-10. Archived from the original on 2025-02-17. Retrieved 2025-02-17.
113. ^ "Our X Games History". X Games. Archived from the original on 2025-02-15. Retrieved 2025-02-20.
114. ^ a b "What is UFS - Universal Frame System". Bladeville. 2022-03-10. Archived from the original on 2022-08-31. Retrieved 2025-02-21.
115. ^ What Happened to the K2 Fatty? // Aggressive Inline Skating (video). Back to Blading. 2018-10-05 – via YouTube. See video transcript on discussions on origin of K2 Fatty, prototype/sample of Fatty Pro, and 2018 Fatty.
116. ^ Vegter, Ivo (2022-05-08). "Review: Roces 5th Element" (video). thisissoul.com. This is Soul. See video transcript on history of Roces, relationship to Rollerblade, 1998 Roces 5th Element, and 2020 version of the 5th Element.
117. ^ "La norme UFS (Universal Frame System)". Le Roller en Ligne (in French). 2018-08-22. Archived from the original on 2025-02-22. Retrieved 2025-02-22.
118. ^ US 6648346, Borel, René, "Frame for a sport article (UFS standard)", published 2003-11-18, issued 2003-11-18, assigned to Salomon SAS
119. ^ "Into Detail: About Frames" (video). www.thisissoul.com. This Is Soul. 2020-10-18. This is the companion video of the article on "Everything about Frames".
120. ^ a b c "Let's talk facts: ROCKIN' MIX4 100/90". ROCKIN’ Frames. 2022-02-10. Archived from the original on 2025-03-02. Retrieved 2025-03-02.
121. ^ a b "Why Heel-to-Ball Is Essential". The Brannock Device Company. Archived from the original on 2025-01-29. Retrieved 2025-03-02.
122. ^ WO application 2010051657, So, Kai Nin, "Bottom structure for inline roller skate shoes", published 2010-05-14
123. ^ Knoll, Matthias; Pfitzner, Jürgen; Arlidge, Scott (2016-07-27). Trinity Mount - The next level (video). Powerslide – via YouTube. Powerslide introduced Trinity for all skating disciplines.
124. ^ US 10524533, Knoll, Matthias, "Roller skate system having a rail and a boot", published 2020-01-07, issued 2020-01-07, assigned to Powerslide GmbH
125. ^ Choong, Adam (2018-05-15). "Trinity Three Point Mount". Inlinex. Archived from the original on 2025-03-03. Retrieved 2025-03-03.
126. ^ Briand, Pascal (2022-03-22). Trinity vs 195 Mounting - PS live stream (video). Powerslide. Archived from the original on 2024-03-23. Retrieved 2025-05-04 – via YouTube. Pascal talks about Trinity's development history and specifications. He compares Trinity mounting to 195mm mounting, including the wide front mounts for better control and pushes.
127. ^ "Types of Inline Skates". Inline Skates. Archived from the original on 2018-10-17. Retrieved 2025-01-06.
128. ^ Vegter, Ivo (4 January 2022). "Everything about wheels". This Is Soul. Archived from the original on 2024-09-13. Retrieved 2025-03-07.
129. ^ "Urethane vs. Polyurethane". Gallagher Corporation. Archived from the original on 2025-03-09. Retrieved 2025-03-09. Quote: "when discussing industrial applications, urethane and polyurethane are essentially the same material. The terms are used interchangeably, and there is no functional difference between them."
130. ^ a b c d "Anatomy of an inline skate wheel". Le Roller en Ligne. 2020-11-03. Archived from the original on 2025-03-08. Retrieved 2025-03-08.
131. ^ Lino, Ricardo (2022-06-23). This Factory Makes the Best Wheels for Inline & Quad Skating, Skateboarding & Scooters (video) – via YouTube. See video transcript for a tour of factory floor and discussions on all aspects of wheel-making.
132. ^ a b c "Polyurethane-Resilience". Gallagher Corporation. Archived from the original on 2024-08-03. Retrieved 2025-03-08.
133. ^ US 2664317, Thomas, Glynn & Cleever, John W, "Composition roller skate wheel", published 1953-12-29, issued 1953-12-29, assigned to Raybestos Manhattan Inc
134. ^ Winner, Tara (2018-06-07). "Sidewalk Surfing: The Gnarly History of Skateboarding Part I (1940s to 1972)". The Strong - National Museum of Play. Archived from the original on 2025-03-16. Retrieved 2025-03-16.
135. ^ "Main's skateboard collection and the Paul Conibear Ramprocker". Overplywood - The History of Skateboarding in Swansea. 2013-02-28. Archived from the original on 2025-03-16. Retrieved 2025-03-16.
136. ^ "Chicago Skates Timeline". Chicago Skates (Chicago Roller Skates). Archived from the original on 2024-09-16. Retrieved 2025-03-08.
137. ^ Weiss, Eric M. (2004-08-17). "A Reinvention Of the Wheel". Washington Post. Washington DC. Archived from the original on 2007-08-08. Retrieved 2024-12-20.
138. ^ "Are Polyurethane Skateboard Wheels Good?". Custom Moulded Polyurethane. 2022-08-24. Archived from the original on 2025-03-08. Retrieved 2025-03-08.
139. ^ a b Bernstein, Ross (2007). "In-Line Hockey In Minnesota". More... Frozen Memories: Celebrating a Century of Minnesota Hockey. Minneapolis, Minn.: Nodin Press. pp. 184–185\. ISBN 978-1932472493. Retrieved 2024-12-24.
140. ^ a b c d "Powerslide Wheels Guide" (PDF). Powerslide. Archived (PDF) from the original on 2024-05-31. Retrieved 2025-03-22.
141. ^ "Hockey brands faq - Labeda". Hockey Office. Archived from the original on 2025-03-29. Retrieved 2025-03-29.
142. ^ a b c d "Wheels for Inline Skates - A Complete Guide". SkatePro. Archived from the original on 2025-01-31. Retrieved 2025-03-27.
143. ^ US 4447093, Cunard, Joel C. & Ziegler, William H., "Wheel", published 1984-05-08, issued 1984-05-08, assigned to Brown Group Recreational Products Inc
144. ^ a b Kopitz, Steve. "Buying Guide for Inline Skate Wheels". Inline Skates. Archived from the original on 2021-08-05. Retrieved 2025-04-04.
145. ^ a b Vegter, Ivo. "Everything about wheel diameter". This Is Soul. Archived from the original on 2025-04-04. Retrieved 2025-04-04. Also reference the companion video shown in the article.
146. ^ a b c d e Anthony D. Chen (1992-05-17). "Skate FAQs: Wheels and Hop-up Kits". Newsgroup: rec.skate. Archived from the original on 2025-03-29. Retrieved 2025-03-29.
147. ^ a b c d Williams, Carlesa (2017-10-25). "Inline Skate Wheels 101". LiveAbout. Archived from the original on 2025-04-04. Retrieved 2025-04-04.
148. ^ a b c Vegter, Ivo. "Everything about wheel profile". This Is Soul. Archived from the original on 2025-04-04. Retrieved 2025-04-04. Also reference the companion video shown in the article.
149. ^ "Aggressive Skate Wheels". SkatePro. Archived from the original on 2025-04-05. Retrieved 2025-04-05.
150. ^ a b c "Choosing hardness of inline skating wheels". Bladeville. 2013-09-17. Archived from the original on 2025-04-18. Retrieved 2025-04-18.
151. ^ a b "Causes of tire rolling resistance, and our protocols when testing it". Outside Online. 2021-09-29. Archived from the original on 2025-04-21. Retrieved 2025-04-21.
152. ^ a b c d "Rolling Resistance and Industrial Wheels" (PDF). Hamilton Caster & Mfg. Co. 2013-02-01. Archived (PDF) from the original on 2025-04-21. Retrieved 2025-04-21.
153. ^ a b c Cross, Rod (2015). "Effects of surface roughness on rolling friction". European Journal of Physics. 36 (6). doi:10.1088/0143-0807/36/6/065029. Archived from the original on 2025-04-27. Retrieved 2025-04-26.
154. ^ a b "Inline Skate Wheel Buying Guide". Inline Warehouse. June 2019. Archived from the original on 2025-03-15. Retrieved 2025-04-17.
155. ^ Anthony D. Chen (1993-11-04). "Q: What are the origins of in-line skates?". Newsgroup: rec.skate. Archived from the original on 2024-12-23. Retrieved 2024-12-23.
156. ^ a b c US 6227622, Roderick, John A.; Chiang, Albert C. & Vandergrift, James A., "Multilayer skate wheel", published 2001-05-08, issued 2001-05-08, assigned to K2 Corp and Fleet National Bank
157. ^ Chartier, Alexandre 'alfathor' (2015-01-18). "Dual density skate wheels: Where does the technology comes from and what is the use of it?". Le Roller en Ligne. Archived from the original on 2025-04-19. Retrieved 2025-04-19.
158. ^ US 7090306, Piper, Neal, "Inline wheel with softer tire and internal support structure", published 2006-08-15, issued 2006-08-15
159. ^ "Reivision wheels: Flex, Recoil and Variant". Revision Hockey. Archived from the original on 2025-04-20. Retrieved 2025-04-20.
160. ^ "Rebound Resilience". Elastomer Institut, part of OPR Group GmbH. Archived from the original on 2025-04-23. Retrieved 2025-04-23.
161. ^ "Hysteresis in Urethane". Gallagher Corporation. Archived from the original on 2025-04-25. Retrieved 2025-04-25.
162. ^ a b c d e Anthony D. Chen (1992-05-02). "Skate FAQs: The Bearing Maintenance File". Newsgroup: rec.skate. Archived from the original on 2025-05-09. Retrieved 2025-05-09.
163. ^ a b c "Powerslide/Wicked Bearing Guide" (PDF). Powerslide. Archived (PDF) from the original on 2024-05-19. Retrieved 2025-05-09.
164. ^ a b c d e f g h i "Rolling Bearings" (PDF). SKF Group. A 1,152 document published by SKF Group. October 2018. Archived (PDF) from the original on 2025-04-07. Retrieved 2025-05-13.`{{cite web}}`: CS1 maint: others (link)
165. ^ a b Chen, Anthony D. "ABEC = HYPE?". Archived from the original on 15 March 2018. Retrieved 15 September 2014.
166. ^ a b Ahrens, Fred (November 2008). "Inline Skates: An Engineer's Perspective". Get Rolling - Liz Miller. Archived from the original on 2010-11-22. Retrieved 2025-05-18.
167. ^ a b c Powell, George A. "Bones® Bearings History". Bones Bearings. Archived from the original on 2008-05-10. Retrieved 2025-05-16.
168. ^ a b Powell, George A. "Maintaining your Bones® Bearings". Bones Bearings. Archived from the original on 2008-05-10. Retrieved 2025-05-16.
169. ^ a b c "Skateboard Bearings - the Truth". Vandem Longboard Shop. Archived from the original on 2020-08-05. Retrieved 2025-05-24.
170. ^ Shulgan, Alex (2023-04-20). "Guide to roller and inline skate bearings 2024". InMove Skates. Archived from the original on 2025-05-11. Retrieved 2025-05-16.
171. ^ a b c Powell, George A. "Abec vs. Skate Rated™". Bones Bearings. Archived from the original on 2014-10-09. Retrieved 2025-05-16.
172. ^ "What are Swiss Bearings?". Devaskation. Archived from the original on 2025-04-18. Retrieved 2025-05-17.
173. ^ "TWINCAM home page". TWINCAM Bearing. Archived from the original on 2013-03-05. Retrieved 2025-05-16.
174. ^ "What are Twincam and ILQ Bearings?". Loco Skates. 2025-02-13. Archived from the original on 2025-05-12. Retrieved 2025-05-16.
175. ^ a b Hambinathan, Arampamoorthy (2020-12-11). "Ceramic Bearings vs Steel Bearings: An Engineering Analysis". Hambini Engineering. Archived from the original on 2021-05-07. Retrieved 2025-05-20.
176. ^ Sweeney, Kevin (2024-02-10). "Factors Affecting Friction Torque in Bearings". Pacific International Bearing. Archived from the original on 2025-05-19. Retrieved 2025-05-20.
177. ^ a b c "Skate Bearing FAQ". Miniature Bearings Australia. 2004-01-30. Archived from the original on 2005-03-07. Retrieved 2025-05-20.
178. ^ Pfeifer, Jeanette. "A Comprehensive Guide to Bearings Seals: Types, Functions, and Applications". BDS Bearings. Archived from the original on 2024-11-14. Retrieved 2025-05-23.
179. ^ "Bearing Nomenclature Guide" (PDF). BDS Bearings. 2024. Archived (PDF) from the original on 2025-05-24. Retrieved 2025-05-24.
180. ^ a b c d e "6 Common Misconceptions About Skateboard Bearings". Fireball Supply / Dragon Bearings. 2020-08-17. Archived from the original on 2025-02-14. Retrieved 2025-05-23.
181. ^ a b "INA/Schaeffler Product Reference Guide (732 pages)" (PDF). Schaeffler. 2003. Archived (PDF) from the original on 2025-05-24. Retrieved 2025-05-24.
182. ^ a b c "NTN Rolling Bearings Handbook" (PDF). NTN-SNR. March 2017. Archived (PDF) from the original on 2018-09-18. Retrieved 2025-05-23.
183. ^ Sanchez, Steven (2022-07-12). "Big wheels inline skates experience". InMove Skates. Archived from the original on 2024-11-05. Retrieved 2025-05-04.
184. ^ a b Lino, Ricardo (2016-12-13). Why Triskates? The Latest Generation Inline Skate (video) – via YouTube. See video transcript.
185. ^ "Endless Frame Spec Comparison & Overview". Endless Blading. Archived from the original on 2025-02-16. Retrieved 2025-02-16.
186. ^ US 6132006, Post, Peter G., "In-line skate wheel axle assembly and frame", published 2000-10-17, issued 2000-10-17
187. ^ US 6309108, Wershe, Richard, "Bearing spacer for in-line skate", published 2001-10-30, issued 2001-10-30
188. ^ a b US application 20190247739, Svensson, John Erik, "Single-wall inline skate frame and skate", published 2019-08-15, assigned to K2 Sports LLC
189. ^ US 7931283, Wegener, Andreas C., "Frame assembly for in-line skate", published 2009-01-29, issued 2011-04-26, assigned to Sunshine Distribution Inc
190. ^ "Inline Skate Wheel Rotation and Maintenance". Inline Skates. Archived from the original on 2021-10-18. Retrieved 2021-10-18.
191. ^ a b c d e f Thierstein, Markus. "Inline Skating Knowledge: Rotating Wheels". Skating Thierstein. Archived from the original on 2025-02-28. Retrieved 2025-04-29.
192. ^ US 2697010, August, Hirschmugl Robert, "Roller skate wheel", published 1954-12-14, issued 1954-12-14
193. ^ a b Verdone, Peter (2012). "Bearings & Lubrication". PVD Designs. Archived from the original on 2012-02-15. Retrieved 2025-05-31.
194. ^ a b c d e US 5685649, Demarest, Charles H.; Jensen, Paul C. & Lutz, Gerard F., "Wheel adapted to eliminate bearing click", published 1997-11-11, issued 1997-11-11, assigned to Kryptonics Inc and Bravo Sports Corp
195. ^ US 5692809, Hook, Kenneth Wayne, "In-line skate wheels", published 1997-12-02, issued 1997-12-02
196. ^ "Radial Ball Bearings". GMN Bearing USA. Archived from the original on 2025-04-26. Retrieved 2025-06-06.
197. ^ a b c "Skate Bearings - your essential guide" (PDF). SMB Bearings. 2020. Archived (PDF) from the original on 2025-06-07. Retrieved 2025-06-06.
198. ^ "What Are the Differences Between Bearings? The various types and special features of bearings". JTEKT Corporation. 2024-11-20. Archived from the original on 2025-01-13. Retrieved 2025-06-06.
199. ^ a b c d "Ball Bearing Internal Clearance". SMB Bearings. Archived from the original on 2025-06-07. Retrieved 2025-06-07.
200. ^ "Precision Ball & Roller Bearings - Internal Geometry of Ball Bearings". New Hampshire Ball Bearings, Inc. Archived from the original on 2025-06-08. Retrieved 2025-06-07.
201. ^ a b c "How to Select the Right Bearing (Part 5): Bearing preload and rigidity". JTEKT Corporation. 2024-11-20. Archived from the original on 2025-06-07. Retrieved 2025-06-07.
202. ^ a b c Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V. (April 2012). "Effect of Internal Clearance on Load Distribution and Life of Radially Loaded Ball and Roller Bearings" (PDF). NTRS - NASA Technical Reports Server. Archived (PDF) from the original on 2024-04-24. Retrieved 2025-06-08.
203. ^ "SKF: Bearing damage and failure analysis" (PDF). website. PUB BU/I3 14219/2 EN. June 2017. Archived (PDF) from the original on 2025-04-07. Retrieved 2025-06-08.`{{cite web}}`: CS1 maint: others (link)
204. ^ "Navigating Misalignment: How Deep Groove Ball Bearings Handle the Challenge". Axis - Baart Industrial Group. Archived from the original on 2025-04-26. Retrieved 2025-06-08.
205. ^ a b "Bearing Preload" (PDF). SKF Group. 2021. Archived (PDF) from the original on 2025-04-07. Retrieved 2025-05-19.
206. ^ Briand, Pascal (2024-02-29). Improve the roll with the WICKED spacer kit - PIT STOP (video). Discourses inline skate spacers: too long, too short, and how to find the right length. Powerslide – via YouTube.
207. ^ a b "How to Select the Right Bearing (Part 4): Bearing limiting speed, running accuracy, and fits". JTEKT Corporation. 2024-11-20. Archived from the original on 2025-01-15. Retrieved 2025-06-07.
208. ^ Vegter, Ivo (2022-02-13). "Everything About Bearing Spacers" (video). thisissoul.com. See video transcript on all aspects of inline skate bearing spacers, including effects of shorter and longer spaces on bearings and bearing frictions. This is Soul.
209. ^ Rajewski, David (2015-06-01). "Why Bearing Spacers Really Matter (skateboards)". Stoked Ride Shop. Archived from the original on 2025-06-21. Retrieved 2025-06-20.
210. ^ "Balanced Rocker". Endless Blading. Archived from the original on 2025-06-26. Retrieved 2025-06-26. Balanced rocker setup with 4x90mm wheels on the Endless Trinity 90 frame.
211. ^ a b c d "Wizard NR Frames (showing NR90)". Wizard Skating. Archived from the original on 2025-04-18. Retrieved 2025-05-28.
212. ^ a b c Kempton, Mark (2007-01-24). "Inline Wheel Setups: A Beginners' Guide - By MarKK". Nottingham Skaters. Archived from the original on 2007-09-28. Retrieved 2025-06-26.
213. ^ a b Weaver, Kris (2025-03-30). "Roller Hockey Chassis: Hi-lo system vs. straight wheel system". Madison Rec Hockey. Archived from the original on 2025-06-28. Retrieved 2025-06-28.
214. ^ "Endless 90 mk2 Frame (165mm mounting with Balance Rocker)". Endless Blading. Archived from the original on 2025-06-29. Retrieved 2025-06-29.
215. ^ "Ninja 90 frame 165mm/Trinity/UFS mountings with V.m Rocker". NN Skates. Archived from the original on 2025-06-29. Retrieved 2025-06-29.
216. ^ "NN Skates - FAQs". NN Skates. Archived from the original on 2025-06-29. Retrieved 2025-06-29.
217. ^ Vegter, Ivo (2021-08-31). "Everything About Grooves" (video). thisissoul.com. See video transcript on history of frame grooves, soulplates, backslide groove, Rollerblade Lightning, Roces Majestic 12 (M12), UFS mounting holes, split, wheel protection, height of grooves, radius of grooves, etc. This is Soul.
218. ^ Ingraham, Lawrence (2018-11-16). What's the history of 50/50? What's the future? // Aggressive Inline Skating (video). Publisher – via YouTube. See video transcript for info on freestyle frame, juice blocks, Balance Frame, etc.

## External links

[edit]

Wikimedia Commons has media related to Inline skates.

* The National Museum of Roller Skating \- many historical roller and inline skates mentioned in this article are featured in this museum's collections.
* Skating Book FAQ / Bibliography, part 1 of 2 \- a listing of inline skating books published in the heyday of inline skating, in the 1990s. Part 1 includes books on inline skating, roller hockey, and quad skating. TOC from each book is reproduced, along with a short summary of the book.

* v
* t
* e

Inline skating

Disciplines|

* Aggressive inline skating
* Vert skating
* Artistic roller skating
* Freestyle slalom skating
* Inline figure skating
* Inline hockey
* Inline speed skating
* Nordic cross skating
* Road skating
* Roller soccer

Physical design|

* Inline skates

Manufacturers|

* Rollerblade
* K2 Sports
* Roller Derby

Related sports|

* Roller skiing
* Freeskating
* Roller skating (quad)

* v
* t
* e

Human-powered transport

Land|

| Pedal power|

* 29er
* Bicycle (outline)
* Bicycle trailer
* BMX bike
* Boneshaker
* Cargo bike
* City bicycle
* Cold-weather biking
* Cruiser bicycle
* Cycle rickshaw
* Cyclo-cross bicycle
* Downhill bike
* Enduro
* Fatbike
* Flat bar road bike
* Folding bicycle
* Go-kart
* Glossary of cycling
* Hybrid bicycle
* Motorized bicycle
* Mountain bike
* Mountain biking
* 27.5
* Downhill
* Singletrack
* Party bike
* Penny-farthing
* Porteur bicycle
* Prone bicycle
* Quadracycle
* Recumbent bicycle
* Road bicycle
* Roadster
* Safety bicycle
* Sociable
* Small-wheel bicycle
* Tandem bicycle
* Touring bicycle
* Track bicycle
* Trailer bike
* Tricycle
* Unicycle
* Utility bicycle
* Velocar
* Velocipede
* Velomobile
* Wheelie bike
* Cold-weather biking (ice cycle)

|

Electric motor assist|

* Electric bicycle
* Pedelec
* Motorized bicycle
* Motorized scooter

Treadle power|

* Treadle bicycle

Other foot power|

* Balance bike
* Dandy horse
* Kick scooter
* Kickbike
* Kicksled
* Brakeboard
* Freeboard
* Freeskates
* Longboard
* Skateboard

Hand power|

* Handcar
* Handcycle
* Hobcart
* Invalid carriage
* Wheelchair

Row action|

* Rowing cycle

Pushed/pulled|

* Baby transport
* Baggage cart
* Bath chair
* Cart
* Flatbed trolley
* Hand truck
* Pulled rickshaw
* Shopping cart
* Shopping caddy
* Stairclimber
* Stretcher
* Toy wagon
* Wheelbarrow
* Sled

Carried|

* Litter/sedan chair
* Scoop stretcher

Weight shifting|

* Trikke
* Pogo stick
* Caster board
* Snakeboard

Gravity|

* Gravity racer
* Billy cart
* Street luge
* Snowboard
* Toboggan
* Summer toboggan
* Gravity biking

Water|

| Hand power|

* Canoe
* Kayak
* Paddleboarding
* Rowing (fixed seat)
* Punt

|

Hand and foot power|

* Rowing (sliding seat)
* Rowing (sliding rigger)

Foot power|

* Hydrocycle
* Hydrofoil
* Pedalo

Amphibious|

* Amphibious cycle

Air|

* Aircraft
* list
* Helicopter
* Ornithopter

Non-vehicular transport|

| Foot power|

* Inline skating
* skates
* Roller skating
* skates
* Running
* Stair climbing
* Walking
* Stair climbing

|

Snow and ice|

* Crampons
* Ice skates
* Ski
* Alpine touring skis
* Cross-country skis
* Telemark skis
* Snowshoes

Related topics|

* Animal-powered transport
* Cycling (outline)
* Bicycle- and human-powered vehicle museums
* Human power
* Zero-emissions vehicle

* v
* t
* e

Footwear

* List of shoe styles
* List of boots
* Shoe
* Shoemaking
* Shoe size

Dress shoes|

* Blucher
* Brogues
* Brothel creepers
* Derby
* Monks
* Oxfords
* Spectator shoes (Co-respondent shoes)
* Winklepickers
* Wholecuts

| Slip-on shoes|

* Court shoes
* Prince Albert slippers
* Loafers
* Venetian-style shoes

|

Women's|

* Ballet flats
* High-heeled footwear
* Mary Janes
* Mojari
* Mules
* Peep-toe shoes
* Saddle shoes
* Slingbacks
* T-bar sandals

Other shoes|

* Driving moccasins
* Flip-flops
* Galoshes
* Platform shoes
* Sandals
* Self-tying shoes
* Slides
* Slippers (Uwabaki)
* Tiger-head shoes
* Veldskoens
* Zōri

Wooden footwear|

* Bakya
* British clogs
* Cantabrian albarcas
* Clogs
* Geta
* Klompen
* Namaksin
* Okobo
* Padukas
* Pattens
* Sabot
* Träskor

Boots|

| Military|

* Ammunition
* Bunny
* Combat
* Jack
* Jump
* Jungle
* Patauga
* Tanker
* Trench

|

Work|

* Australian work
* Cowboy
* Engineer
* Hip
* Jika-tabi
* Rigger
* Steel-toe
* Waders

Fashion boots|

* Chelsea (Beatle)
* Chukka
* Go-go
* Knee-high
* Over-the-knee
* Platform
* Thigh-high
* Ugg

Other|

* Jodhpur
* Wellington
* Ballet
* Bean

Sport-related footwear|

* Ballet shoes
* Boat shoes
* Climbing shoes
* Cross country running shoes
* Cycling shoes
* Football boots
* Ghillies
* Hiking boots
* Ice skates
* Inline skates
* Kung fu shoes
* Minimalist shoes
* Motorcycle boots
* Mountaineering boots
* Plimsolls
* Pointe shoes
* Racing flats
* Racing shoes
* Riding boots
* Roller shoes
* Roller skates
* Sabatons
* Safari boots
* Skate shoes
* Ski boots
* Sneakers
* Swimfins
* Water shoes
* Wrestling shoes

Folk footwear|

* Abacas
* Abarkas
* Alpargatas
* Avarcas
* Balghas
* Bast shoes
* Ciocie
* Clogs
* Espadrilles
* Furlane
* Galesh
* Geta
* Giveh
* Haferlschuh
* Hnyat-phanats
* Huarache
* Hwa
* Jipsin
* Jorabs
* Kamiks
* Kolhapuri chappals
* Moccasins
* Mojaris
* Mukluks
* Nalins
* Okobo
* Opanci
* Peshawari chappals
* Snowshoes
* Tsarouchi
* Takunya
* Upanah
* Valenkis
* Waraji
* Zōri

Historical footwear|

* Areni-1 shoes
* Buskins
* Calcei
* Caligae
* Carbatina
* Cavalier boots
* Chinese styles
* Chopines
* Duckbill shoes
* Flowerpot shoes
* Hessians
* Lotus shoes
* Pampooties
* Pigaches
* Poulaines
* Socci
* Turnshoes

Shoe construction|

* Bespoke shoes
* Blake construction
* Goodyear welt
* Shoe buckle
* Shoelaces
* Toe box

| High heels|

* Clear heels
* Kitten heels
* Spool heels
* Stiletto heels
* Wedges

|

Hosiery|

* Anklets
* Bobby socks
* Dress socks
* Footwraps
* Knee highs
* Pantyhose
* Sock
* Stocking
* Tights
* Toe socks
* Tabi

Related|

* Abandoned footwear
* Spats

Authority control databases

National|

* Germany
* United States
* Israel

Other|

* Yale LUX

*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template