Noise (electronics)

Random fluctuation in an electrical signal

This article is about fundamental noise processes in electronics. For electronic noise arising from outside sources, see Electromagnetic compatibility and Electromagnetic interference. For acoustic noise due to electromagnetic fields, see Electromagnetically induced acoustic noise and vibration. For other uses, see Noise (disambiguation).

Random fluctuations of voltage in pink noise

In electronics, noise is an unwanted disturbance in an electrical signal.[1]: 5

Noise generated by electronic devices varies greatly as it is produced by several different effects.

In particular, noise is inherent in physics and central to thermodynamics. Any conductor with electrical resistance will generate thermal noise inherently. The final elimination of thermal noise in electronics can only be achieved cryogenically, and even then quantum noise would remain inherent.

Electronic noise is a common component of noise in signal processing.

In communication systems, noise is an error or undesired random disturbance of a useful information signal in a communication channel. The noise is a summation of unwanted or disturbing energy from natural and sometimes man-made sources. Noise is, however, typically distinguished from interference,[a] for example in the signal-to-noise ratio (SNR), signal-to-interference ratio (SIR) and signal-to-noise plus interference ratio (SNIR) measures. Noise is also typically distinguished from distortion, which is an unwanted systematic alteration of the signal waveform by the communication equipment, for example in signal-to-noise and distortion ratio (SINAD) and total harmonic distortion plus noise (THD+N) measures.

While noise is generally unwanted, it can serve a useful purpose in some applications, such as random number generation or dither.

Uncorrelated noise sources add according to the sum of their powers.[2]

## Noise types

[edit]

Different types of noise are generated by different devices and different processes. Thermal noise is unavoidable at non-zero temperature (see fluctuation-dissipation theorem), while other types depend mostly on device type (such as shot noise,[1][3] which needs a steep potential barrier) or manufacturing quality and semiconductor defects, such as conductance fluctuations, including 1/f noise.

### Thermal noise

[edit]

Main article: Johnson–Nyquist noise

Johnson–Nyquist noise[1] (more often thermal noise) is unavoidable, and generated by the random thermal motion of charge carriers (usually electrons), inside an electrical conductor, which happens regardless of any applied voltage.

Thermal noise is approximately white, meaning that its power spectral density is nearly equal throughout the frequency spectrum. The amplitude of the signal has very nearly a Gaussian probability density function. A communication system affected by thermal noise is often modelled as an additive white Gaussian noise (AWGN) channel.

### Shot noise

[edit]

Main article: Shot noise

Shot noise in electronic devices results from unavoidable random statistical fluctuations of the electric current when the charge carriers (such as electrons) traverse a gap. If electrons flow across a barrier, then they have discrete arrival times. Those discrete arrivals exhibit shot noise. Typically, the barrier in a diode is used.[4] Shot noise is similar to the noise created by rain falling on a tin roof. The flow of rain may be relatively constant, but the individual raindrops arrive discretely.[5]

The root-mean-square value of the shot noise current in is given by the Schottky formula.

i n = 2 I q Δ B {\displaystyle i_{n}={\sqrt {2Iq\Delta B}}}

where I is the DC current, q is the charge of an electron, and ΔB is the bandwidth in hertz. The Schottky formula assumes independent arrivals.

Vacuum tubes exhibit shot noise because the electrons randomly leave the cathode and arrive at the anode (plate). A tube may not exhibit the full shot noise effect: the presence of a space charge tends to smooth out the arrival times (and thus reduce the randomness of the current). Pentodes and screen-grid tetrodes exhibit more noise than triodes because the cathode current splits randomly between the screen grid and the anode.

Conductors and resistors typically do not exhibit shot noise because the electrons thermalize and move diffusively within the material; the electrons do not have discrete arrival times. Shot noise has been demonstrated in mesoscopic resistors when the size of the resistive element becomes shorter than the electron–phonon scattering length.[6]

### Partition noise

[edit]

Where current divides between two (or more) paths,[7] noise occurs as a result of random fluctuations that occur during this division.

For this reason, a transistor will have more noise than the combined shot noise from its two PN junctions.

### Flicker noise

[edit]

Main articles: Flicker noise and 1/f noise

Flicker noise, also known as 1/f noise, is a signal or process with a frequency spectrum that falls off steadily into the higher frequencies, with a pink spectrum. It occurs in almost all electronic devices and results from a variety of effects.

### Burst noise

[edit]

Main article: Burst noise

Burst noise consists of sudden step-like transitions between two or more discrete voltage or current levels, as high as several hundred microvolts, at random and unpredictable times. Each shift in offset voltage or current lasts for several milliseconds to seconds. It is also known as popcorn noise for the popping or crackling sounds it produces in audio circuits.

### Transit-time noise

[edit]

If the time taken by the electrons to travel from emitter to collector in a transistor becomes comparable to the period of the signal being amplified, that is, at frequencies above VHF and beyond, the transit-time effect takes place and the noise input impedance of the transistor decreases. From the frequency at which this effect becomes significant, it increases with frequency and quickly dominates other sources of noise.[8]

## Coupled noise

[edit]

See also: Electromagnetic compatibility

While noise may be generated in the electronic circuit itself, additional noise energy can be coupled into a circuit from the external environment, by inductive coupling or capacitive coupling, or through the antenna of a radio receiver.

### Sources

[edit]

Intermodulation noise
Caused when signals of different frequencies share the same non-linear medium.

Crosstalk
Phenomenon in which a signal transmitted in one circuit or channel of a transmission system creates undesired interference onto a signal in another channel.

Interference
Modification or disruption of a signal travelling along a medium

Atmospheric noise
Also called static noise, it is caused by lightning discharges in thunderstorms and other electrical disturbances occurring in nature, such as corona discharge.

Industrial noise
Sources such as automobiles, aircraft, ignition electric motors and switching gear, High voltage wires and fluorescent lamps cause industrial noise. These noises are produced by the discharge present in all these operations.

Solar noise
Noise that originates from the Sun is called solar noise. Under normal conditions, there is approximately constant radiation from the Sun due to its high temperature, but solar storms can cause a variety of electrical disturbances. The intensity of solar noise varies over time in a solar cycle.

Cosmic noise
Distant stars generate noise called cosmic noise. While these stars are too far away to individually affect terrestrial communications systems, their large number leads to appreciable collective effects. Cosmic noise has been observed in a range from 8 MHz to 1.43 GHz, the latter frequency corresponding to the 21-cm hydrogen line. Apart from man-made noise, it is the strongest component over the range of about 20 to 120 MHz. Little cosmic noise below 20MHz penetrates the ionosphere, while its eventual disappearance at frequencies in excess of 1.5 GHz is probably governed by the mechanisms generating it and its absorption by hydrogen in interstellar space.[citation needed]

### Mitigation

[edit]

In many cases noise found on a signal in a circuit is unwanted. There are many different noise reduction techniques that can reduce the noise picked up by a circuit.

1. Faraday cage – A Faraday cage enclosing a circuit can be used to isolate the circuit from external noise sources. A Faraday cage cannot address noise sources that originate in the circuit itself or those carried in on its inputs, including the power supply.
2. Capacitive coupling – Capacitive coupling allows an AC signal from one part of the circuit to be picked up in another part through the interaction of electric fields. Where coupling is unintended, the effects can be addressed through improved circuit layout and grounding.
3. Ground loops – When grounding a circuit, it is important to avoid ground loops. Ground loops occur when there is a voltage difference between two ground connections. A good way to fix this is to bring all the ground wires to the same potential in a ground bus.
4. Shielding cables – A shielded cable can be thought of as a Faraday cage for wiring and can protect the wires from unwanted noise in a sensitive circuit. The shield must be grounded to be effective. Grounding the shield at only one end can avoid a ground loop on the shield.
5. Twisted pair wiring – Twisting wires in a circuit will reduce electromagnetic noise. Twisting the wires decreases the loop size in which a magnetic field can run through to produce a current between the wires. Small loops may exist between wires twisted together, but the magnetic field going through these loops induces a current flowing in opposite directions in alternate loops on each wire and so there is no net noise current.
6. Notch filters – Notch filters or band-rejection filters are useful for eliminating a specific noise frequency. For example, power lines within a building run at 50 or 60 Hz line frequency. A sensitive circuit will pick up this frequency as noise. A notch filter tuned to the line frequency can remove the noise.

Thermal noise can be reduced by cooling of circuits - this is typically only employed in high accuracy high-value applications such as radio telescopes.

## Quantification

[edit]

The noise level in an electronic system is typically measured as an electrical power N in watts or dBm, a root mean square (RMS) voltage (identical to the noise standard deviation) in volts, dBμV or a mean squared error (MSE) in volts squared. Examples of electrical noise-level measurement units are dBu, dBm0, dBrn, dBrnC, and dBrn(f1 − f2), dBrn(144-line). Noise may also be characterized by its probability distribution and noise spectral density N0(f) in watts per hertz.

A noise signal is typically considered as a linear addition to a useful information signal. Typical signal quality measures involving noise are signal-to-noise ratio (SNR or S/N), signal-to-quantization noise ratio (SQNR) in analog-to-digital conversion and compression, peak signal-to-noise ratio (PSNR) in image and video coding and noise figure in cascaded amplifiers. In a carrier-modulated passband analogue communication system, a certain carrier-to-noise ratio (CNR) at the radio receiver input would result in a certain signal-to-noise ratio in the detected message signal. In a digital communications system, a certain Eb/N0 (normalized signal-to-noise ratio) would result in a certain bit error rate. Telecommunication systems strive to increase the ratio of signal level to noise level in order to effectively transfer data. Noise in telecommunication systems is a product of both internal and external sources to the system.

Noise is a random process, characterized by stochastic properties such as its variance, distribution, and spectral density. The spectral distribution of noise can vary with frequency, so its power density is measured in watts per hertz (W/Hz). Since the power in a resistive element is proportional to the square of the voltage across it, noise voltage (density) can be described by taking the square root of the noise power density, resulting in volts per root hertz ( V / H z {\displaystyle \scriptstyle \mathrm {V} /{\sqrt {\mathrm {Hz} }}} ). Integrated circuit devices, such as operational amplifiers commonly quote equivalent input noise level in these terms (at room temperature).

## Dither

[edit]

If the noise source is correlated with the signal, such as in the case of quantisation error, the intentional introduction of additional noise, called dither, can reduce overall noise in the bandwidth of interest. This technique allows retrieval of signals below the nominal detection threshold of an instrument. This is an example of stochastic resonance.

## See also

[edit]

* Active noise control for noise reduction through cancellation
* Colors of noise
* Discovery of cosmic microwave background radiation
* Error detection and correction for digital signals subject to noise
* Generation–recombination noise
* Matched filter for noise reduction in modems
* Noise (signal processing)
* Noise reduction and for audio and images
* Phonon noise

## Notes

[edit]

1. ^ E.g. crosstalk, deliberate jamming or other unwanted electromagnetic interference from specific transmitters

## References

[edit]

1. ^ a b c Motchenbacher, C. D.; Connelly, J. A. (1993). Low-noise electronic system design. Wiley Interscience. ISBN 0-471-57742-1.
2. ^ Sobering, Tim J. (1999). "Noise in Electronic Systems" (PDF). Archived (PDF) from the original on 2023-05-20. Retrieved 2024-04-07.
3. ^ Kish, L. B.; Granqvist, C. G. (November 2000). "Noise in nanotechnology". Microelectronics Reliability. 40 (11). Elsevier: 1833–1837\. doi:10.1016/S0026-2714(00)00063-9.
4. ^ Ott, Henry W. (1976), Noise Reduction Techniques in Electronic Systems, John Wiley, pp. 208, 218, ISBN 0-471-65726-3
5. ^ MacDonald, D. K. C. (2006), Noise and Fluctuations: An Introduction, Dover Publications Inc, p. 2, ISBN 0-486-45029-5
6. ^ Steinbach, Andrew; Martinis, John; Devoret, Michel (1996-05-13). "Observation of Hot-Electron Shot Noise in a Metallic Resistor". Phys. Rev. Lett. 76 (20): 38.6 – 38.9. Bibcode:1996PhRvL..76...38M. doi:10.1103/PhysRevLett.76.38. PMID 10060428.
7. ^ "Partition noise". Retrieved 2021-11-05.
8. ^ Communication Theory. Technical Publications. 1991. pp. 3–6\. ISBN 9788184314472.

* This article incorporates public domain material from Federal Standard 1037C. General Services Administration. Archived from the original on 2022-01-22. (in support of MIL-STD-188).

## Further reading

[edit]

* Sh. Kogan (1996). Electronic Noise and Fluctuations in Solids. Cambridge University Press. ISBN 0-521-46034-4.
* Scherz, Paul. (2006, Nov 14) Practical Electronics for Inventors. ed. McGraw-Hill.

## External links

[edit]

* Active Filter (Sallen & Key) Noise Study. Archived 2015-05-22 at the Wayback Machine.
* White noise calculator, thermal noise – Voltage in microvolts, conversion to noise level in dBu and dBV and vice versa

* v
* t
* e

Noise (physics and telecommunications)

General|

* Acoustic quieting
* Distortion
* Noise cancellation
* Noise control
* Noise measurement
* Noise power
* Noise reduction
* Noise temperature
* Phase distortion

Noise in...|

* Audio
* Buildings
* Electronics
* Environment
* Government regulation
* Human health
* Images
* Radio
* Rooms
* Ships
* Sound masking
* Transportation
* Video

Class of noise|

* Additive white Gaussian noise (AWGN)
* Atmospheric noise
* Background noise
* Brownian noise
* Burst noise
* Cosmic noise
* Flicker noise
* Gaussian noise
* Grey noise
* Infrasound
* Jitter
* Johnson–Nyquist noise (thermal noise)
* Pink noise
* Quantization error (or q. noise)
* Shot noise
* White noise
* Coherent noise
* Value noise
* Gradient noise
* Worley noise

Engineering
terms|

* Channel noise level
* Circuit noise level
* Effective input noise temperature
* Equivalent noise resistance
* Equivalent pulse code modulation noise
* Impulse noise (audio)
* Noise figure
* Noise floor
* Noise shaping
* Noise spectral density
* Noise, vibration, and harshness (NVH)
* Phase noise
* Pseudorandom noise
* Statistical noise

Ratios|

* Carrier-to-noise ratio (C/N)
* Carrier-to-receiver noise density (C/kT)
* dBrnC
* Eb/N0 (energy per bit to noise density)
* Es/N0 (energy per symbol to noise density)
* Modulation error ratio (MER)
* Signal, noise and distortion (SINAD)
* Signal-to-interference ratio (S/I)
* Signal-to-noise ratio (S/N, SNR)
* Signal-to-noise ratio (imaging)
* Signal-to-interference-plus-noise ratio (SINR)
* Signal-to-quantization-noise ratio (SQNR)
* Contrast-to-noise ratio (CNR)

Related topics|

* List of noise topics
* Acoustics
* Colors of noise
* Interference (communication)
* Noise generator
* Spectrum analyzer
* Thermal radiation

Denoise
methods|

| General|

* Low-pass filter
* Median filter
* Total variation denoising
* Wavelet denoising

|

2D (Image)|

* Gaussian blur
* Anisotropic diffusion
* Bilateral filter
* Non-local means
* Block-matching and 3D filtering (BM3D)
* Shrinkage Fields
* Denoising autoencoder (DAE)
* Deep Image Prior

* v
* t
* e

Analog television broadcasting topics

Systems|

* 180-line
* 343-line
* 375-line
* 405-line (System A)
* 441-line
* 455-line
* 525-line (System M)
* 625-line (System B, System C, System D, System G, System H, System I, System K, System L, System N)
* 819-line (System E, System F)

Color systems|

* NTSC
* NTSC-J
* Clear-Vision
* PAL
* PAL-M
* PAL-S
* PALplus
* SECAM

Video|

* Back porch and front porch
* Black level
* Blanking level
* Chrominance
* Chrominance subcarrier
* Colorburst
* Color killer
* Color TV
* Composite video
* Frame (video)
* Horizontal scan rate
* Horizontal blanking interval
* Luma
* Nominal analogue blanking
* Overscan
* Raster scan
* Safe area
* Television lines
* Vertical blanking interval
* White clipper

Sound|

* Multichannel Television Sound
* NICAM
* Sound-in-Syncs
* Zweikanalton

Modulation|

* Frequency modulation
* Quadrature amplitude modulation
* Vestigial sideband modulation (VSB)

Transmission|

* Amplifiers
* Antenna (radio)
* Broadcast transmitter/Transmitter station
* Cavity amplifier
* Differential gain
* Differential phase
* Diplexer
* Dipole antenna
* Dummy load
* Frequency mixer
* Intercarrier method
* Intermediate frequency
* Output power of an analog TV transmitter
* Pre-emphasis
* Residual carrier
* Split sound system
* Superheterodyne transmitter
* Television receive-only
* Direct-broadcast satellite television
* Television transmitter
* Terrestrial television
* Transposer
* Digital television transition

Frequencies & bands|

* Frequency offset
* Microwave transmission
* Television channel frequencies
* UHF
* VHF

Propagation|

* Beam tilt
* Distortion
* Earth bulge
* Field strength in free space
* Noise (electronics)
* Null fill
* Path loss
* Radiation pattern
* Skew
* Television interference

Testing|

* Distortionmeter
* Field strength meter
* Vectorscope
* VIT signals
* Zero reference pulse

Artifacts|

* Dot crawl
* Ghosting
* Hanover bars
* Sparklies

Authority control databases: National |

* Czech Republic

|

*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template