Nuclear reactor

Device for controlled nuclear reactions

This article is about nuclear fission reactors. For nuclear fusion reactors, see Fusion power.

"Nuclear pile" redirects here. For nuclear stockpiles, see List of states with nuclear weapons.

From top, left to right

1. Chicago Pile-1, the first artificial nuclear reactor
2. Shippingport Atomic Power Station, the first peacetime reactor
3. HTR-10, a prototype to the first Generation IV reactor, HTR-PM
4. The Convair NB-36H, the first aircraft to test an onboard reactor
5. Operation Sea Orbit, the first nuclear-powered surface vessel circumnavigation
6. The Chernobyl sarcophagus, built to contain the effects of the 1986 disaster

A nuclear reactor is a device used to initiate and control a fission nuclear chain reaction. They are used for commercial electricity, marine propulsion, weapons production and research. Fissile nuclei (primarily uranium-235 or plutonium-239) absorb single neutrons and split, releasing energy and multiple neutrons, which can induce further fission. Reactors stabilize this, regulating neutron absorbers and moderators in the core. Fuel efficiency is exceptionally high; low-enriched uranium is 120,000 times more energy dense than coal.[1][2]

Heat from nuclear fission is passed to a working fluid coolant. In commercial reactors, this drives turbines and electrical generator shafts. Some reactors are used for district heating, and isotope production for medical and industrial use.

Following the 1938 discovery of fission, many countries initiated military nuclear research programs. Early subcritical experiments probed neutronics. In 1942, the first artificial[note 1] critical nuclear reactor, Chicago Pile-1, was built by the Metallurgical Laboratory.[4] From 1944, for weapons production, the first large-scale reactors were operated at the Hanford Site. The pressurized water reactor design, used in ~70% of commercial reactors, was developed for US Navy submarine propulsion, beginning with S1W in 1953.[5] In 1954, nuclear electricity production began with the Soviet Obninsk plant.[6]

Spent fuel can be reprocessed, reducing nuclear waste and recovering reactor-usable fuel.[7] This also poses a proliferation risk via production of plutonium and tritium for nuclear weapons.

Reactor accidents have been caused by combinations of design and operator failure. The 1979 Three Mile Island accident, at INES Level 5, and the 1986 Chernobyl disaster and 2011 Fukushima disaster, both at Level 7, all had major effects on the nuclear industry and anti-nuclear movement.

As of 2025[update], there are 417 commercial reactors, 226 research reactors, and over 200 marine propulsion reactors in operation globally.[8][9][10][11] Commercial reactors provide 9% of the global electricity supply,[12] compared to 30% from renewables,[13] together comprising low-carbon electricity. Almost 90% of this comes from pressurized and boiling water reactors.[5] Other designs include gas-cooled, fast-spectrum, breeder, heavy-water, molten-salt, and small modular; each optimizes safety, efficiency, cost, fuel type, enrichment, and burnup.

## Terminology

[edit]

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (May 2025) (Learn how and when to remove this message)

|

During early 1940s nuclear research, the phrase "atomic pile" was used for any assembly involving uranium and attempts at neutron multiplication, including the majority which were subcritical. After Chicago Pile-1 demonstrated a self-sustaining chain reaction, the "reactor" terminology became more common. The phrases "nuclear pile" and "atomic reactor" were also common.

Critical mass experiments, while being far simpler, are sometimes referred to as research reactors, such as the Godiva device.

"Nuclear reactor" is predominantly used to refer to the nuclear fission reactor. It can also refer to a nuclear fusion reactor, of which only net negative power systems have been constructed. Radioisotope thermoelectric generators and radioisotope heater units, while deriving power from nuclear decay reactions, are not referred to as nuclear reactors as they do not induce reactions.

## Operation

[edit]

Main article: Nuclear reactor physics

An example of an induced nuclear fission event. A neutron is absorbed by the nucleus of a uranium-235 atom, which in turn splits into fast-moving lighter elements (fission products) and free neutrons. Though both reactors and nuclear weapons rely on nuclear chain reactions, the rate of reactions in a reactor is much slower than in a bomb.

Just as conventional thermal power stations generate electricity by harnessing the thermal energy released from burning fossil fuels, nuclear reactors convert the energy released by controlled nuclear fission into thermal energy for further conversion to mechanical or electrical forms.

### Fission

[edit]

Main article: Nuclear fission

When a large fissile atomic nucleus such as uranium-235, uranium-233, or plutonium-239 absorbs a neutron, it may undergo nuclear fission. The heavy nucleus splits into two or more lighter nuclei, (the fission products), releasing kinetic energy, gamma radiation, and free neutrons. A portion of these neutrons may be absorbed by other fissile atoms and trigger further fission events, which release more neutrons, and so on. This is known as a nuclear chain reaction.

To control such a nuclear chain reaction, control rods containing neutron poisons and neutron moderators are able to change the portion of neutrons that will go on to cause more fission.[14] Nuclear reactors generally have automatic and manual systems to shut the fission reaction down if monitoring or instrumentation detects unsafe conditions.[15]

### Heat generation

[edit]

The reactor core generates heat in a number of ways:

* The kinetic energy of fission products is converted to thermal energy when these nuclei collide with nearby atoms.
* The reactor absorbs some of the gamma rays produced during fission and converts their energy into heat.
* Heat is produced by the radioactive decay of fission products and materials that have been activated by neutron absorption. This decay heat source will remain for some time even after the reactor is shut down.

A kilogram of uranium-235 (U-235) converted via nuclear processes releases approximately three million times more energy than a kilogram of coal burned conventionally (7.2 × 1013 joules per kilogram of uranium-235 versus 2.4 × 107 joules per kilogram of coal).[16][17][original research?]

The fission of one kilogram of uranium-235 releases about 19 billion kilocalories, so the energy released by 1 kg of uranium-235 corresponds to that released by burning 2.7 million kg of coal.

### Cooling

[edit]

A nuclear reactor coolant – usually water but sometimes a gas or a liquid metal (like liquid sodium or lead) or molten salt – is circulated past the reactor core to absorb the heat that it generates. The heat is carried away from the reactor and is then used to generate steam. Most reactor systems employ a cooling system that is physically separated from the water that will be boiled to produce pressurized steam for the turbines, like the pressurized water reactor. However, in some reactors the water for the steam turbines is boiled directly by the reactor core; for example the boiling water reactor.[18]

### Reactivity control

[edit]

Main articles: Nuclear reactor physics, Passive nuclear safety, Delayed neutron, Iodine pit, SCRAM, and Decay heat

The rate of fission reactions within a reactor core can be adjusted by controlling the quantity of neutrons that are able to induce further fission events. Nuclear reactors typically employ several methods of neutron control to adjust the reactor's power output. Some of these methods arise naturally from the physics of radioactive decay and are simply accounted for during the reactor's operation, while others are mechanisms engineered into the reactor design for a distinct purpose.

The fastest method for adjusting levels of fission-inducing neutrons in a reactor is via movement of the control rods. Control rods are made of so-called neutron poisons and therefore absorb neutrons. When a control rod is inserted deeper into the reactor, it absorbs more neutrons than the material it displaces – often the moderator. This action results in fewer neutrons available to cause fission and reduces the reactor's power output. Conversely, extracting the control rod will result in an increase in the rate of fission events and an increase in power.

The physics of radioactive decay also affects neutron populations in a reactor. One such process is delayed neutron emission by a number of neutron-rich fission isotopes. These delayed neutrons account for about 0.65% of the total neutrons produced in fission, with the remainder (termed "prompt neutrons") released immediately upon fission. The fission products which produce delayed neutrons have half-lives for their decay by neutron emission that range from milliseconds to as long as several minutes, and so considerable time is required to determine exactly when a reactor reaches the critical point. Keeping the reactor in the zone of chain reactivity where delayed neutrons are necessary to achieve a critical mass state allows mechanical devices or human operators to control a chain reaction in "real time"; otherwise the time between achievement of criticality and nuclear meltdown as a result of an exponential power surge from the normal nuclear chain reaction, would be too short to allow for intervention. This last stage, where delayed neutrons are no longer required to maintain criticality, is known as the prompt critical point. There is a scale for describing criticality in numerical form, in which bare criticality is known as zero dollars and the prompt critical point is one dollar, and other points in the process interpolated in cents.

In some reactors, the coolant also acts as a neutron moderator. A moderator increases the power of the reactor by causing the fast neutrons that are released from fission to lose energy and become thermal neutrons. Thermal neutrons are more likely than fast neutrons to cause fission. If the coolant is a moderator, then temperature changes can affect the density of the coolant/moderator and therefore change power output. A higher temperature coolant would be less dense, and therefore a less effective moderator.

In other reactors, the coolant acts as a poison by absorbing neutrons in the same way that the control rods do. In these reactors, power output can be increased by heating the coolant, which makes it a less dense poison. Nuclear reactors generally have automatic and manual systems to scram the reactor in an emergency shut down. These systems insert large amounts of poison (often boron in the form of boric acid) into the reactor to shut the fission reaction down if unsafe conditions are detected or anticipated.[19]

Most types of reactors are sensitive to a process variously known as xenon poisoning, or the iodine pit. The common fission product Xenon-135 produced in the fission process acts as a neutron poison that absorbs neutrons and therefore tends to shut the reactor down. Xenon-135 accumulation can be controlled by keeping power levels high enough to destroy it by neutron absorption as fast as it is produced. Fission also produces iodine-135, which in turn decays (with a half-life of 6.57 hours) to new xenon-135. When the reactor is shut down, iodine-135 continues to decay to xenon-135, making restarting the reactor more difficult for a day or two, as the xenon-135 decays into cesium-135, which is not nearly as poisonous as xenon-135, with a half-life of 9.2 hours. This temporary state is the "iodine pit." If the reactor has sufficient extra reactivity capacity, it can be restarted. As the extra xenon-135 is transmuted to xenon-136, which is much less a neutron poison, within a few hours the reactor experiences a "xenon burnoff (power) transient". Control rods must be further inserted to replace the neutron absorption of the lost xenon-135. Failure to properly follow such a procedure was a key step in the Chernobyl disaster.[20]

Reactors used in nuclear marine propulsion (especially nuclear submarines) often cannot be run at continuous power around the clock in the same way that land-based power reactors are normally run, and in addition often need to have a very long core life without refueling. For this reason many designs use highly enriched uranium but incorporate burnable neutron poison in the fuel rods.[21] This allows the reactor to be constructed with an excess of fissionable material, which is nevertheless made relatively safe early in the reactor's fuel burn cycle by the presence of the neutron-absorbing material which is later replaced by normally produced long-lived neutron poisons (far longer-lived than xenon-135) which gradually accumulate over the fuel load's operating life.

### Electrical power generation

[edit]

The energy released in the fission process generates heat, some of which can be converted into usable energy. A common method of harnessing this thermal energy is to use it to boil water to produce pressurized steam which will then drive a steam turbine that turns an alternator and generates electricity.[19]

### Life-times

[edit]

Modern nuclear power plants are typically designed for a lifetime of 60 years, while older reactors were built with a planned typical lifetime of 30–40 years, though many of those have received renovations and life extensions of 15–20 years.[22] Some believe nuclear power plants can operate for as long as 80 years or longer with proper maintenance and management. While most components of a nuclear power plant, such as steam generators, are replaced when they reach the end of their useful lifetime, the overall lifetime of the power plant is limited by the life of components that cannot be replaced when aged by wear and neutron embrittlement, such as the reactor pressure vessel.[23] At the end of their planned life span, plants may get an extension of the operating license for some 20 years and in the US even a "subsequent license renewal" (SLR) for an additional 20 years.[24][25]

Even when a license is extended, it does not guarantee the reactor will continue to operate, particularly in the face of safety concerns or incident.[26] Many reactors are closed long before their license or design life expired and are decommissioned. The costs for replacements or improvements required for continued safe operation may be so high that they are not cost-effective. Or they may be shut down due to technical failure.[27] Other ones have been shut down because the area was contaminated, like Fukushima, Three Mile Island, Sellafield, and Chernobyl.[28] The British branch of the French concern EDF Energy, for example, extended the operating lives of its Advanced Gas-cooled Reactors (AGR) with only between 3 and 10 years.[29] All seven AGR plants were expected to be shut down in 2022 and in decommissioning by 2028.[30] Hinkley Point B was extended from 40 to 46 years, and closed. The same happened with Hunterston B, also after 46 years.

An increasing number of reactors is reaching or crossing their design lifetimes of 30 or 40 years. In 2014, Greenpeace warned that the lifetime extension of ageing nuclear power plants amounts to entering a new era of risk. It estimated the current European nuclear liability coverage in average to be too low by a factor of between 100 and 1,000 to cover the likely costs, while at the same time, the likelihood of a serious accident happening in Europe continues to increase as the reactor fleet grows older.[31]

## Early reactors

[edit]

See also: Nuclear fission § History

The Chicago Pile, the first artificial nuclear reactor, built in secrecy at the University of Chicago in 1942 during World War II as part of the US's Manhattan project Lise Meitner and Otto Hahn in their laboratory Some of the Chicago Pile Team, including Enrico Fermi and Leó Szilárd

The neutron was discovered in 1932 by British physicist James Chadwick. The concept of a nuclear chain reaction brought about by nuclear reactions mediated by neutrons was first realized shortly thereafter, by Hungarian scientist Leó Szilárd, in 1933. He filed a patent for his idea of a simple reactor the following year while working at the Admiralty in London, England.[32] However, Szilárd's idea did not incorporate the idea of nuclear fission as a neutron source, since that process was not yet discovered. Szilárd's ideas for nuclear reactors using neutron-mediated nuclear chain reactions in light elements proved unworkable.

Inspiration for a new type of reactor using uranium came from the discovery by Otto Hahn, Lise Meitner, and Fritz Strassmann in 1938 that bombardment of uranium with neutrons (provided by an alpha-on-beryllium fusion reaction, a "neutron howitzer") produced a barium residue, which they reasoned was created by fission of the uranium nuclei. In their second publication on nuclear fission in February 1939, Hahn and Strassmann predicted the existence and liberation of additional neutrons during the fission process, opening the possibility of a nuclear chain reaction. Subsequent studies in early 1939 (one of them by Szilárd and Fermi), revealed that several neutrons were indeed released during fission, making available the opportunity for the nuclear chain reaction that Szilárd had envisioned six years previously.

On 2 August 1939, Albert Einstein signed a letter to President Franklin D. Roosevelt (written by Szilárd) suggesting that the discovery of uranium's fission could lead to the development of "extremely powerful bombs of a new type", giving impetus to the study of reactors and fission. Szilárd and Einstein knew each other well and had worked together years previously, but Einstein had never thought about this possibility for nuclear energy until Szilard reported it to him, at the beginning of his quest to produce the Einstein-Szilárd letter to alert the U.S. government.

Shortly after, Nazi Germany invaded Poland in 1939, starting World War II in Europe. The U.S. was not yet officially at war, but in October, when the Einstein-Szilárd letter was delivered to him, Roosevelt commented that the purpose of doing the research was to make sure "the Nazis don't blow us up." The U.S. nuclear project followed, although with some delay as there remained skepticism (some of it from Enrico Fermi) and also little action from the small number of officials in the government who were initially charged with moving the project forward.

The following year, the U.S. Government received the Frisch–Peierls memorandum from the UK, which stated that the amount of uranium needed for a chain reaction was far lower than had previously been thought. The memorandum was a product of the MAUD Committee, which was working on the UK atomic bomb project, known as Tube Alloys, later to be subsumed within the Manhattan Project.

Eventually, the first artificial nuclear reactor, Chicago Pile-1, was constructed at the University of Chicago, by a team led by Italian physicist Enrico Fermi, in late 1942. By this time, the program had been pressured for a year by U.S. entry into the war. The Chicago Pile achieved criticality on 2 December 1942[4] at 3:25 PM. The reactor support structure was made of wood, which supported a pile (hence the name) of graphite blocks, embedded in which was natural uranium oxide 'pseudospheres' or 'briquettes'.

Soon after the Chicago Pile, the Metallurgical Laboratory developed a number of nuclear reactors for the Manhattan Project starting in 1943. The primary purpose for the largest reactors (located at the Hanford Site in Washington), was the mass production of plutonium for nuclear weapons. Fermi and Szilard applied for a patent on reactors on 19 December 1944. Its issuance was delayed for 10 years because of wartime secrecy.[33]

"World's first nuclear power plant" is the claim made by signs at the site of the EBR-I, which is now a museum near Arco, Idaho. Originally called "Chicago Pile-4", it was carried out under the direction of Walter Zinn for Argonne National Laboratory.[34] This experimental LMFBR operated by the U.S. Atomic Energy Commission produced 0.8 kW in a test on 20 December 1951[35] and 100 kW (electrical) the following day,[36] having a design output of 200 kW (electrical).

Besides the military uses of nuclear reactors, there were political reasons to pursue civilian use of atomic energy. U.S. President Dwight Eisenhower made his famous Atoms for Peace speech to the UN General Assembly on 8 December 1953. This diplomacy led to the dissemination of reactor technology to U.S. institutions and worldwide.[37]

The first nuclear power plant built for civil purposes was the AM-1 Obninsk Nuclear Power Plant, launched on 27 June 1954 in the Soviet Union. It produced around 5 MW (electrical). It was built after the F-1 (nuclear reactor) which was the first reactor to go critical in Europe, and was also built by the Soviet Union.

After World War II, the U.S. military sought other uses for nuclear reactor technology. Research by the Army led to the power stations for Camp Century, Greenland and McMurdo Station, Antarctica Army Nuclear Power Program. The Air Force Nuclear Bomber project resulted in the Molten-Salt Reactor Experiment. The U.S. Navy succeeded when they steamed the USS Nautilus (SSN-571) on nuclear power 17 January 1955.

The first commercial nuclear power station, Calder Hall in Sellafield, England was opened in 1956 with an initial capacity of 50 MW (later 200 MW).[38][39]

The first portable nuclear reactor "Alco PM-2A" was used to generate electrical power (2 MW) for Camp Century from 1960 to 1963.[40]

### Table by date

[edit]

Reactors constructed before 1950  Name  | Alternate names  | Country  | Location  | Moderator  | Criticality date

|
|
|
|
|

Chicago Pile-1 | CP-1  |  United States | University of Chicago, Illinois  | Graphite  | 2 December 1942[41]
Chicago Pile-2 | CP-2  |  United States | Site A, Illinois  | Graphite  | 20 March 1943[42]
Oak Ridge Graphite Reactor | X-10, Clinton Pile  |  United States | Clinton Laboratories, Tennessee  | Graphite  | 4 November 1943[43]
305 Test Pile[44] |  |  United States | Hanford Site, Washington  | Graphite  | March 1944[45][when?]
Chicago Pile-3 | CP-3  |  United States | Site A, Illinois  | Heavy water  | 15 May 1944[46]
Los Alamos LOPO Reactor[47] | LOPO  |  United States | Los Alamos Laboratory, New Mexico  | Light water  | 9 May 1944[48]
B Reactor |  |  United States | Hanford Site, Washington  | Graphite  | 26 September 1944[49]
Los Alamos Water Boiler | HYPO  |  United States | Los Alamos Laboratory, New Mexico  | Light water  | December 1944[50][when?]
D Reactor  |  |  United States | Hanford Site, Washington  | Graphite  | December 1944[51]
Dragon |  |  United States | Los Alamos Laboratory, New Mexico  | None (fast)  | 20 January 1945[52]
F Reactor  |  |  United States | Hanford Site, Washington  | Graphite  | February 1945[51]
Trinity, first US nuclear test | 16 July 1945
Zero Energy Experimental Pile | ZEEP  |  Canada | Chalk River Laboratories, Ontario  | Heavy water  | 5 September 1945[53]
Los Alamos Fast Reactor | Clementine  |  United States | Los Alamos Laboratory, New Mexico  | None (fast)  | 19 November 1946[54]
F-1 |  |  Soviet Union | Laboratory No. 2, Moscow  | Graphite  | 25 December 1946
National Research Experimental | NRX  |  Canada | Chalk River Laboratories, Ontario  | Heavy water  | 22 July 1947[55]
Graphite Low Energy Experimental Pile | GLEEP  |  United Kingdom | Atomic Energy Research Establishment, Oxfordshire  | Graphite  | 15 August 1947[56]
Reactor A  |  |  Soviet Union | Mayak Production Association, Chelyabinsk Oblast  | Graphite  | 10 June 1948[57]
British Experimental Pile Operation | BEPO  |  United Kingdom | Atomic Energy Research Establishment, Oxfordshire  | Graphite  | 3 July 1948[58]
Eau Lourde-1 (Heavy Water-1)  | EL-1, Zoé  |  France | Fort de Châtillon, Paris  | Heavy water  | 15 December 1948[59]
Physical Boiler on Fast Neutrons | FKBN  |  Soviet Union | Design Bureau No. 11, Sarov  | None (fast)  | 1 February 1949[60]
TVR | TVR  |  Soviet Union | Laboratory No. 3, Moscow  | Heavy water  | April 1949[61]
RDS-1, first Soviet nuclear test | 29 August 1949
H Reactor  |  |  United States | Hanford Site, Washington  | Graphite  | October 1949[51]

### Table by country

[edit]

First nations to operate a nuclear reactor  Country  | First reactor  | Criticality date  | First grid-connected reactor  | Connection date

|
|
|
|

United States | CP-1 | 2 December 1942[62] | Shippingport Atomic Power Station | 18 December 1957[63]
Canada | ZEEP | 5 September 1945[64] | Nuclear Power Demonstration | 4 June 1962[65]
Soviet Union | F-1 | 25 December 1946[66] | Obninsk Nuclear Power Plant | 27 June 1954[67]
United Kingdom | GLEEP | 15 August 1947[68] | Calder Hall nuclear power station | 27 August 1956[69]
France | EL-1 (Zoé) | 15 December 1948[70] | Marcoule Nuclear Site | 22 April 1959[71]
Norway[note 2] | JEEP | 30 July 1951[72] | None constructed  | n/a
Sweden | R1 | 13 July 1954[73] | Ågesta Nuclear Plant | 1 May 1964[74]
Belgium | BR1 [nl; fr] | 11 May 1956[75] | BR3 [nl; fr] | 10 October 1962[76]
India | Apsara | 4 August 1956[77] | Tarapur Atomic Power Station | 1 April 1969[78]
Japan | JRR-1 [ja] | 27 August 1957  | Tōkai Nuclear Power Plant | 25 July 1966
West Germany | FRM-I [de] | 31 October 1957[79] | Kahl Nuclear Power Plant | 17 June 1961[80]
East Germany | RFR [de] | 16 December 1957[81] | Rheinsberg Nuclear Power Plant | 6 May 1966[82]
China | HWRR | 27 September 1958[83] | Qinshan Nuclear Power Plant | 15 December 1991[84]
Italy | ISPRA-1 [it] | 20 November 1959[85] | Latina Nuclear Power Plant | May 1963
Primary coolant system showing reactor pressure vessel (red), steam generators (purple), pressurizer (blue), and pumps (green) in the three coolant loop Hualong One pressurized water reactor design

## Reactor types

[edit]

* PWR: 277 (63.2%)
* BWR: 80 (18.3%)
* GCR: 15 (3.4%)
* PHWR: 49 (11.2%)
* LWGR: 15 (3.4%)
* FBR: 2 (0.5%)

Number of reactors by type (end 2014)[86]

* PWR: 257.2 (68.3%)
* BWR: 75.5 (20.1%)
* GCR: 8.2 (2.2%)
* PHWR: 24.6 (6.5%)
* LWGR: 10.2 (2.7%)
* FBR: 0.6 (0.2%)

Net power capacity (GWe) by type (end 2014)[86]

NC State's PULSTAR Reactor is a 1 MW pool-type research reactor with 4% enriched, pin-type fuel consisting of UO2 pellets in zircaloy cladding.

### Classifications

[edit]

#### By type of nuclear reaction

[edit]

All commercial power reactors are based on nuclear fission. They generally use uranium and its product plutonium as nuclear fuel, though a thorium fuel cycle is also possible. Fission reactors can be divided roughly into two classes, depending on the energy of the neutrons that sustain the fission chain reaction:

* Thermal-neutron reactors use slowed or thermal neutrons to keep up the fission of their fuel. Almost all current reactors are of this type. These contain neutron moderator materials that slow neutrons until their neutron temperature is thermalized, that is, until their kinetic energy approaches the average kinetic energy of the surrounding particles. Thermal neutrons have a far higher cross section (probability) of fissioning the fissile nuclei uranium-235, plutonium-239, and plutonium-241, and a relatively lower probability of neutron capture by uranium-238 (U-238) compared to the faster neutrons that originally result from fission, allowing use of low-enriched uranium or even natural uranium fuel. The moderator is often also the coolant, usually water under high pressure to increase the boiling point. These are surrounded by a reactor vessel, instrumentation to monitor and control the reactor, radiation shielding, and a containment building.
* Fast-neutron reactors use fast neutrons to cause fission in their fuel. They do not have a neutron moderator, and use less-moderating coolants. Maintaining a chain reaction requires the fuel to be more highly enriched in fissile material (about 20% or more) due to the relatively lower probability of fission versus capture by U-238. Fast reactors have the potential to produce less transuranic waste because all actinides are fissionable with fast neutrons,[87] but they are more difficult to build and more expensive to operate. Overall, fast reactors are less common than thermal reactors in most applications. Some early power stations were fast reactors, as are some Russian naval propulsion units. Construction of prototypes is continuing (see fast breeder or generation IV reactors).

In principle, fusion power could be produced by nuclear fusion of elements such as the deuterium isotope of hydrogen. While an ongoing rich research topic since at least the 1940s, no self-sustaining fusion reactor for any purpose has ever been built.

#### By moderator material

[edit]

Used by thermal reactors:

* Graphite-moderated reactors
* Mostly early reactors such as the Chicago pile, Obninsk am 1, Windscale piles, RBMK, Magnox, and others such as AGR use graphite as a moderator.
* Water moderated reactors
* Heavy-water reactors (Used in Canada,[88] India, Argentina, China, Pakistan, Romania and South Korea).[89]
* Light-water-moderated reactors (LWRs). Light-water reactors (the most common type of thermal reactor) use ordinary water to moderate and cool the reactors.[88] Because the light hydrogen isotope is a slight neutron poison, these reactors need artificially enriched fuels. When at operating temperature, if the temperature of the water increases, its density drops, and fewer neutrons passing through it are slowed enough to trigger further reactions. That negative feedback stabilizes the reaction rate. Graphite and heavy-water reactors tend to be more thoroughly thermalized than light water reactors. Due to the extra thermalization, and the absence of the light hydrogen poisoning effects these types can use natural uranium/unenriched fuel.
* Light-element-moderated reactors.
* Molten-salt reactors (MSRs) are moderated by light elements such as lithium or beryllium, which are constituents of the coolant/fuel matrix salts "LiF" and "BeF2", "LiCl" and "BeCl2" and other light element containing salts can all cause a moderating effect.
* Liquid metal cooled reactors, such as those whose coolant is a mixture of lead and bismuth, may use BeO as a moderator.
* Organically moderated reactors (OMR) use biphenyl and terphenyl as moderator and coolant.

#### By coolant

[edit]

Treatment of the interior part of a VVER-1000 reactor frame at Atommash In thermal nuclear reactors (LWRs in specific), the coolant acts as a moderator that must slow the neutrons before they can be efficiently absorbed by the fuel.

* Water cooled reactor. These constitute the great majority of operational nuclear reactors: as of 2014, 93% of the world's nuclear reactors are water cooled, providing about 95% of the world's total nuclear generation capacity.[86]
* Pressurized water reactor (PWR) Pressurized water reactors constitute the large majority of all Western nuclear power plants.
* A primary characteristic of PWRs is a pressurizer, a specialized pressure vessel. Most commercial PWRs and naval reactors use pressurizers. During normal operation, a pressurizer is partially filled with water, and a steam bubble is maintained above it by heating the water with submerged heaters. During normal operation, the pressurizer is connected to the primary reactor pressure vessel (RPV) and the pressurizer "bubble" provides an expansion space for changes in water volume in the reactor. This arrangement also provides a means of pressure control for the reactor by increasing or decreasing the steam pressure in the pressurizer using the pressurizer heaters.
* Pressurized heavy water reactors are a subset of pressurized water reactors, sharing the use of a pressurized, isolated heat transport loop, but using heavy water as coolant and moderator for the greater neutron economies it offers.
* Boiling water reactor (BWR)
* BWRs are characterized by boiling water around the fuel rods in the lower portion of a primary reactor pressure vessel. A boiling water reactor uses 235U, enriched as uranium dioxide, as its fuel. The fuel is assembled into rods housed in a steel vessel that is submerged in water. The nuclear fission causes the water to boil, generating steam. This steam flows through pipes into turbines. The turbines are driven by the steam, and this process generates electricity.[90] During normal operation, pressure is controlled by the amount of steam flowing from the reactor pressure vessel to the turbine.
* Supercritical water reactor (SCWR)
* SCWRs are a Generation IV reactor concept where the reactor is operated at supercritical pressures and water is heated to a supercritical fluid, which never undergoes a transition to steam yet behaves like saturated steam, to power a steam generator.
* Reduced moderation water reactor [RMWR] which use more highly enriched fuel with the fuel elements set closer together to allow a faster neutron spectrum sometimes called an Epithermal neutron Spectrum.
* Pool-type reactor can refer to unpressurized water cooled open pool reactors,[91] but not to be confused with pool type LMFBRs, which are sodium cooled.
* Some reactors have been cooled by heavy water which also served as a moderator. Examples include:
* Early CANDU reactors (later ones use heavy water moderator but light water coolant)
* DIDO class research reactors
* Liquid metal cooled reactor. Since water is a moderator, it cannot be used as a coolant in a fast reactor. Liquid metal coolants have included sodium, NaK, lead, lead-bismuth eutectic, and in early reactors, mercury.
* Sodium-cooled fast reactor
* Lead-cooled fast reactor
* Gas cooled reactors are cooled by a circulating gas. In commercial nuclear power plants carbon dioxide has usually been used, for example in current British AGR nuclear power plants and formerly in a number of first generation British, French, Italian, and Japanese plants. Nitrogen[92] and helium have also been used, helium being considered particularly suitable for high temperature designs. Use of the heat varies, depending on the reactor. Commercial nuclear power plants run the gas through a heat exchanger to make steam for a steam turbine. Some experimental designs run hot enough that the gas can directly power a gas turbine.
* Molten-salt reactors (MSRs) are cooled by circulating a molten salt, typically a eutectic mixture of fluoride salts, such as FLiBe. In a typical MSR, the coolant is also used as a matrix in which the fissile material is dissolved. Other eutectic salt combinations used include "ZrF4" with "NaF" and "LiCl" with "BeCl2".
* Organic nuclear reactors use organic fluids such as biphenyl and terphenyl as coolant rather than water.

#### By generation

[edit]

* Generation I reactor (early prototypes such as Shippingport Atomic Power Station, research reactors, non-commercial power producing reactors)
* Generation II reactor (most current nuclear power plants, 1965–1996)
* Generation III reactor (evolutionary improvements of existing designs, 1996–2016)
* Generation III+ reactor (evolutionary development of Gen III reactors, offering improvements in safety over Gen III reactor designs, 2017–2021)[93]
* Generation IV reactor (technologies still under development; unknown start date, see below)[94]
* Generation V reactor (designs which are theoretically possible, but which are not being actively considered or researched at present).

In 2003, the French Commissariat à l'Énergie Atomique (CEA) was the first to refer to "Gen II" types in Nucleonics Week.[95]

The first mention of "Gen III" was in 2000, in conjunction with the launch of the Generation IV International Forum (GIF) plans.

"Gen IV" was named in 2000, by the United States Department of Energy (DOE), for developing new plant types.[96]

#### By type of fuel

[edit]

* Uranium
* Plutonium
* Mixed oxide (MOX) fuel
* Uranium-plutonium alloy[citation needed]
* Transuranium element mix (neptunium, plutonium, americium, curium)[citation needed]

#### By phase of fuel

[edit]

* Solid fueled
* Ceramic
* Oxide
* Carbide
* Nitride
* Metal
* Fluid fueled
* Aqueous homogeneous reactor
* Molten-salt reactor
* Molten metal reactor (e.g. LAMPRE)[citation needed]
* Gas fueled (theoretical)

#### By shape of the core

[edit]

* Cubical
* Cylindrical
* Octagonal
* Spherical
* Slab
* Annulus

#### By use

[edit]

* Electricity
* Nuclear power plants including small modular reactors
* Propulsion, see nuclear propulsion
* Nuclear marine propulsion
* Various proposed forms of rocket propulsion
* Other uses of heat
* Desalination
* Heat for domestic and industrial heating
* Hydrogen production for use in a hydrogen economy
* Production reactors for transmutation of elements
* Breeder reactors are capable of producing more fissile material than they consume during the fission chain reaction (by converting fertile U-238 to Pu-239, or Th-232 to U-233). Thus, a uranium breeder reactor, once running, can be refueled with natural or even depleted uranium, and a thorium breeder reactor can be refueled with thorium; however, an initial stock of fissile material is required.[97]
* Creating various radioactive isotopes, such as americium for use in smoke detectors, and cobalt-60, molybdenum-99 and others, used for imaging and medical treatment.
* Production of materials for nuclear weapons such as weapons-grade plutonium
* Providing a source of neutron radiation (for example with the pulsed Godiva device) and positron radiation[clarification needed] (e.g. neutron activation analysis and potassium-argon dating[clarification needed])
* Research reactor: Typically reactors used for research and training, materials testing, or the production of radioisotopes for medicine and industry. These are much smaller than power reactors or those propelling ships, and many are on university campuses. There are about 280 such reactors operating, in 56 countries. Some operate with high-enriched uranium fuel, and international efforts are underway to substitute low-enriched fuel.[98]

### Current technologies

[edit]

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (June 2015) (Learn how and when to remove this message)

|

Diablo Canyon – a PWR

* Pressurized water reactors (PWR) [moderator: high-pressure water; coolant: high-pressure water]

These reactors use a pressure vessel to contain the nuclear fuel, control rods, moderator, and coolant. The hot radioactive water that leaves the pressure vessel is looped through a steam generator, which in turn heats a secondary (nonradioactive) loop of water to steam that can run turbines. They represent the majority (around 80%) of current reactors. This is a thermal neutron reactor design, the newest of which are the Russian VVER-1200, Japanese Advanced Pressurized Water Reactor, American AP1000, Chinese Hualong Pressurized Reactor and the Franco-German European Pressurized Reactor. All the United States Naval reactors are of this type.

* Boiling water reactors (BWR) [moderator: low-pressure water; coolant: low-pressure water]

A BWR is like a PWR without the steam generator. The lower pressure of its cooling water allows it to boil inside the pressure vessel, producing the steam that runs the turbines. Unlike a PWR, there is no primary and secondary loop. The thermal efficiency of these reactors can be higher, and they can be simpler, and even potentially more stable and safe. This is a thermal-neutron reactor design, the newest of which are the Advanced Boiling Water Reactor and the Economic Simplified Boiling Water Reactor.
The CANDU Qinshan Nuclear Power Plant

* Pressurized Heavy Water Reactor (PHWR) [moderator: high-pressure heavy water; coolant: high-pressure heavy water]

A Canadian design (known as CANDU), very similar to PWRs but using heavy water. While heavy water is significantly more expensive than ordinary water, it has greater neutron economy (creates a higher number of thermal neutrons), allowing the reactor to operate without fuel enrichment facilities. Instead of using a single large pressure vessel as in a PWR, the fuel is contained in hundreds of pressure tubes. These reactors are fueled with natural uranium and are thermal-neutron reactor designs. PHWRs can be refueled while at full power, (online refueling) which makes them very efficient in their use of uranium (it allows for precise flux control in the core). CANDU PHWRs have been built in Canada, Argentina, China, India, Pakistan, Romania, and South Korea. India also operates a number of PHWRs, often termed 'CANDU derivatives', built after the Government of Canada halted nuclear dealings with India following the 1974 Smiling Buddha nuclear weapon test.
The Ignalina Nuclear Power Plant – a RBMK type (closed 2009)

* Reaktor Bolshoy Moschnosti Kanalniy (High Power Channel Reactor) (RBMK) (also known as a Light-Water Graphite-moderated Reactor—LWGR) [moderator: graphite; coolant: high-pressure water]

A Soviet design, RBMKs are in some respects similar to CANDU in that they can be refueled during power operation and employ a pressure tube design instead of a PWR-style pressure vessel. However, unlike CANDU they are unstable and large, making containment buildings for them expensive. A series of critical safety flaws have also been identified with the RBMK design, though some of these were corrected following the Chernobyl disaster. Their main attraction is their use of light water and unenriched uranium. As of 2024, 7 remain open, mostly due to safety improvements and help from international safety agencies such as the U.S. Department of Energy. Despite these safety improvements, RBMK reactors are still considered one of the most dangerous reactor designs in use. RBMK reactors were deployed only in the former Soviet Union.
The Magnox Sizewell A nuclear power station The Torness nuclear power station – an AGR

* Gas-cooled reactor (GCR) and advanced gas-cooled reactor (AGR) [moderator: graphite; coolant: carbon dioxide]

These designs have a high thermal efficiency compared with PWRs due to higher operating temperatures. There are a number of operating reactors of this design, mostly in the United Kingdom, where the concept was developed. Older designs (i.e. Magnox stations) are either shut down or will be in the near future. However, the AGRs have an anticipated life of a further 10 to 20 years. This is a thermal-neutron reactor design. Decommissioning costs can be high due to the large volume of the reactor core.

* Liquid metal fast-breeder reactor (LMFBR) [moderator: none; coolant: liquid metal]

Scaled-down model of TOPAZ nuclear reactor

This totally unmoderated reactor design produces more fuel than it consumes. They are said to "breed" fuel, because they produce fissionable fuel during operation because of neutron capture. These reactors can function much like a PWR in terms of efficiency, and do not require much high-pressure containment, as the liquid metal does not need to be kept at high pressure, even at very high temperatures. These reactors are fast neutron, not thermal neutron designs. These reactors come in two types:
The Superphénix, closed in 1998, was one of the few FBRs.

Lead-cooled

Using lead as the liquid metal provides excellent radiation shielding, and allows for operation at very high temperatures. Also, lead is (mostly) transparent to neutrons, so fewer neutrons are lost in the coolant, and the coolant does not become radioactive. Unlike sodium, lead is mostly inert, so there is less risk of explosion or accident, but such large quantities of lead may be problematic from toxicology and disposal points of view. Often a reactor of this type would use a lead-bismuth eutectic mixture. In this case, the bismuth would present some minor radiation problems, as it is not quite as transparent to neutrons, and can be transmuted to a radioactive isotope more readily than lead. The Russian Alfa class submarine uses a lead-bismuth-cooled fast reactor as its main power plant.
Sodium-cooled

Most LMFBRs are of this type. The TOPAZ, BN-350 and BN-600 in USSR; Superphénix in France; and Fermi-I in the United States were reactors of this type. The sodium is relatively easy to obtain and work with, and it also manages to actually prevent corrosion on the various reactor parts immersed in it. However, sodium explodes violently when exposed to water, so care must be taken, but such explosions would not be more violent than (for example) a leak of superheated fluid from a pressurized-water reactor. The Monju reactor in Japan suffered a sodium leak in 1995 and could not be restarted until May 2010. The EBR-I, the first reactor to have a core meltdown, in 1955, was also a sodium-cooled reactor.

* Pebble-bed reactors (PBR) [moderator: graphite; coolant: helium]

These use fuel molded into ceramic balls, and then circulate gas through the balls. The result is an efficient, low-maintenance, very safe reactor with inexpensive, standardized fuel. The prototypes were the AVR and the THTR-300 in Germany, which produced up to 308MW of electricity between 1985 and 1989 until it was shut down after experiencing a series of incidents and technical difficulties. The HTR-10 is operating in China, where the HTR-PM is being developed. The HTR-PM is expected to be the first generation IV reactor to enter operation.[99]

* Molten-salt reactors (MSR) [moderator: graphite, or none for fast spectrum MSRs; coolant: molten salt mixture]

These dissolve the fuels in fluoride or chloride salts, or use such salts for coolant. MSRs potentially have many safety features, including the absence of high pressures or highly flammable components in the core. They were initially designed for aircraft propulsion due to their high efficiency and high power density. One prototype, the Molten-Salt Reactor Experiment, was built to confirm the feasibility of the Liquid fluoride thorium reactor, a thermal spectrum reactor which would breed fissile uranium-233 fuel from thorium.

* Aqueous homogeneous reactor (AHR) [moderator: high-pressure light or heavy water; coolant: high-pressure light or heavy water]

These reactors use as fuel soluble nuclear salts (usually uranium sulfate or uranium nitrate) dissolved in water and mixed with the coolant and the moderator. As of April 2006, only five AHRs were in operation.[100]

### Future and developing technologies

[edit]

#### Advanced reactors

[edit]

More than a dozen advanced reactor designs are in various stages of development.[101] Some are evolutionary from the PWR, BWR and PHWR designs above, and some are more radical departures. The former include the advanced boiling water reactor (ABWR), two of which are now operating with others under construction, and the planned passively safe Economic Simplified Boiling Water Reactor (ESBWR) and AP1000 units (see Nuclear Power 2010 Program).

* The integral fast reactor (IFR) was built, tested and evaluated during the 1980s and then retired under the Clinton administration in the 1990s due to nuclear non-proliferation policies of the administration. Recycling spent fuel is the core of its design and it therefore produces only a fraction of the waste of current reactors.[102]
* The pebble-bed reactor, a high-temperature gas-cooled reactor (HTGCR), is designed so high temperatures reduce power output by Doppler broadening of the fuel's neutron cross-section. It uses ceramic fuels so its safe operating temperatures exceed the power-reduction temperature range. Most designs are cooled by inert helium. Helium is not subject to steam explosions, resists neutron absorption leading to radioactivity, and does not dissolve contaminants that can become radioactive. Typical designs have more layers (up to 7) of passive containment than light water reactors (usually 3). A unique feature that may aid safety is that the fuel balls actually form the core's mechanism, and are replaced one by one as they age. The design of the fuel makes fuel reprocessing expensive.
* The small, sealed, transportable, autonomous reactor (SSTAR) is being primarily researched and developed in the US, intended as a fast breeder reactor that is passively safe and could be remotely shut down in case the suspicion arises that it is being tampered with.
* The Clean and Environmentally Safe Advanced Reactor (CAESAR) is a nuclear reactor concept that uses steam as a moderator – this design is in development.
* The reduced moderation water reactor builds upon the Advanced boiling water reactor ABWR) that is presently in use. It is not a complete fast reactor instead using mostly epithermal neutrons, which are between thermal and fast neutrons in speed.
* The hydrogen-moderated self-regulating nuclear power module (HPM) is a reactor design emanating from the Los Alamos National Laboratory that uses uranium hydride as fuel.
* Subcritical reactors are designed to be safer and more stable, but pose a number of engineering and economic difficulties. One example is the energy amplifier.
* Thorium-based reactors – It is possible to convert Thorium-232 into U-233 in reactors specially designed for the purpose. In this way, thorium, which is four times more abundant than uranium, can be used to breed U-233 nuclear fuel.[103] U-233 is also believed to have favourable nuclear properties as compared to traditionally used U-235, including better neutron economy and lower production of long lived transuranic waste.
* Advanced heavy-water reactor (AHWR) – A proposed heavy water moderated nuclear power reactor that will be the next generation design of the PHWR type. Under development in the Bhabha Atomic Research Centre (BARC), India.
* KAMINI – A unique reactor using Uranium-233 isotope for fuel. Built in India by BARC and Indira Gandhi Center for Atomic Research (IGCAR).
* India is also planning to build fast breeder reactors using the thorium – Uranium-233 fuel cycle. The FBTR (Fast Breeder Test Reactor) in operation at Kalpakkam (India) uses Plutonium as a fuel and liquid sodium as a coolant.
* China, which has control of the Cerro Impacto deposit, has a reactor and hopes to replace coal energy with nuclear energy.[104]

Rolls-Royce aims to sell nuclear reactors for the production of synfuel for aircraft.[105]

#### Generation IV reactors

[edit]

Generation IV reactors are a set of theoretical nuclear reactor designs. These are generally not expected to be available for commercial use before 2040–2050,[106] although the World Nuclear Association suggested that some might enter commercial operation before 2030.[94] Current reactors in operation around the world are generally considered second- or third-generation systems, with the first-generation systems having been retired some time ago. Research into these reactor types was officially started by the Generation IV International Forum (GIF) based on eight technology goals. The primary goals being to improve nuclear safety, improve proliferation resistance, minimize waste and natural resource utilization, and to decrease the cost to build and run such plants.[107]

* Gas-cooled fast reactor
* Lead-cooled fast reactor
* Molten-salt reactor
* Sodium-cooled fast reactor
* Supercritical water reactor
* Very-high-temperature reactor

#### Generation V+ reactors

[edit]

Generation V reactors are designs which are theoretically possible, but which are not being actively considered or researched at present. Though some generation V reactors could potentially be built with current or near term technology, they trigger little interest for reasons of economics, practicality, or safety.

* Liquid-core reactor. A closed loop liquid-core nuclear reactor, where the fissile material is molten uranium or uranium solution cooled by a working gas pumped in through holes in the base of the containment vessel.
* Gas-core reactor. A closed loop version of the nuclear lightbulb rocket, where the fissile material is gaseous uranium hexafluoride contained in a fused silica vessel. A working gas (such as hydrogen) would flow around this vessel and absorb the UV light produced by the reaction. This reactor design could also function as a rocket engine, as featured in Harry Harrison's 1976 science-fiction novel Skyfall. In theory, using UF6 as a working fuel directly (rather than as a stage to one, as is done now) would mean lower processing costs, and very small reactors. In practice, running a reactor at such high power densities would probably produce unmanageable neutron flux, weakening most reactor materials, and therefore as the flux would be similar to that expected in fusion reactors, it would require similar materials to those selected by the International Fusion Materials Irradiation Facility.
* Gas core EM reactor. As in the gas core reactor, but with photovoltaic arrays converting the UV light directly to electricity.[108] This approach is similar to the experimentally proved photoelectric effect that would convert the X-rays generated from aneutronic fusion into electricity, by passing the high energy photons through an array of conducting foils to transfer some of their energy to electrons, the energy of the photon is captured electrostatically, similar to a capacitor. Since X-rays can go through far greater material thickness than electrons, many hundreds or thousands of layers are needed to absorb the X-rays.[109]
* Fission fragment reactor. A fission fragment reactor is a nuclear reactor that generates electricity by decelerating an ion beam of fission byproducts instead of using nuclear reactions to generate heat. By doing so, it bypasses the Carnot cycle and can achieve efficiencies of up to 90% instead of 40–45% attainable by efficient turbine-driven thermal reactors. The fission fragment ion beam would be passed through a magnetohydrodynamic generator to produce electricity.
* Hybrid nuclear fusion. Would use the neutrons emitted by fusion to fission a blanket of fertile material, like U-238 or Th-232 and transmute other reactor's spent nuclear fuel/nuclear waste into relatively more benign isotopes.

#### Fusion reactors

[edit]

Main article: Fusion power

Controlled nuclear fusion could in principle be used in fusion power plants to produce power without the complexities of handling actinides, but significant scientific and technical obstacles remain. Despite research having started in the 1950s, no commercial fusion reactor is expected before 2050. The ITER project is currently leading the effort to harness fusion power.

## Nuclear fuel cycle

[edit]

Main article: Nuclear fuel cycle

Thermal reactors generally depend on refined and enriched uranium. Some nuclear reactors can operate with a mixture of plutonium and uranium (see MOX). The process by which uranium ore is mined, processed, enriched, used, possibly reprocessed and disposed of is known as the nuclear fuel cycle.

Under 1% of the uranium found in nature is the easily fissionable U-235 isotope and as a result most reactor designs require enriched fuel. Enrichment involves increasing the percentage of U-235 and is usually done by means of gaseous diffusion or gas centrifuge. The enriched result is then converted into uranium dioxide powder, which is pressed and fired into pellet form. These pellets are stacked into tubes which are then sealed and called fuel rods. Many of these fuel rods are used in each nuclear reactor.

Most BWR and PWR commercial reactors use uranium enriched to about 4% U-235, and some commercial reactors with a high neutron economy do not require the fuel to be enriched at all (that is, they can use natural uranium). According to the International Atomic Energy Agency there are at least 100 research reactors in the world fueled by highly enriched (weapons-grade/90% enrichment) uranium. Theft risk of this fuel (potentially used in the production of a nuclear weapon) has led to campaigns advocating conversion of this type of reactor to low-enrichment uranium (which poses less threat of proliferation).[110]

Fissile U-235 and non-fissile but fissionable and fertile U-238 are both used in the fission process. U-235 is fissionable by thermal (i.e. slow-moving) neutrons. A thermal neutron is one which is moving about the same speed as the atoms around it. Since all atoms vibrate proportionally to their absolute temperature, a thermal neutron has the best opportunity to fission U-235 when it is moving at this same vibrational speed. On the other hand, U-238 is more likely to capture a neutron when the neutron is moving very fast. This U-239 atom will soon decay into plutonium-239, which is another fuel. Pu-239 is a viable fuel and must be accounted for even when a highly enriched uranium fuel is used. Plutonium fissions will dominate the U-235 fissions in some reactors, especially after the initial loading of U-235 is spent. Plutonium is fissionable with both fast and thermal neutrons, which make it ideal for either nuclear reactors or nuclear bombs.

Most reactor designs in existence are thermal reactors and typically use water as a neutron moderator (moderator means that it slows down the neutron to a thermal speed) and as a coolant. But in a fast breeder reactor, some other kind of coolant is used which will not moderate or slow the neutrons down much. This enables fast neutrons to dominate, which can effectively be used to constantly replenish the fuel supply. By merely placing cheap unenriched uranium into such a core, the non-fissionable U-238 will be turned into Pu-239, "breeding" fuel.

In thorium fuel cycle thorium-232 absorbs a neutron in either a fast or thermal reactor. The thorium-233 beta decays to protactinium-233 and then to uranium-233, which in turn is used as fuel. Hence, like uranium-238, thorium-232 is a fertile material.

### Fueling of nuclear reactors

[edit]

The amount of energy in the reservoir of nuclear fuel is frequently expressed in terms of "full-power days," which is the number of 24-hour periods (days) a reactor is scheduled for operation at full power output for the generation of heat energy. The number of full-power days in a reactor's operating cycle (between refueling outage times) is related to the amount of fissile uranium-235 (U-235) contained in the fuel assemblies at the beginning of the cycle. A higher percentage of U-235 in the core at the beginning of a cycle will permit the reactor to be run for a greater number of full-power days.

At the end of the operating cycle, the fuel in some of the assemblies is "spent", having spent four to six years in the reactor producing power. This spent fuel is discharged and replaced with new (fresh) fuel assemblies.[citation needed] Though considered "spent," these fuel assemblies contain a large quantity of fuel.[citation needed] In practice it is economics that determines the lifetime of nuclear fuel in a reactor. Long before all possible fission has taken place, the reactor is unable to maintain 100%, full output power, and therefore, income for the utility lowers as plant output power lowers. Most nuclear plants operate at a very low profit margin due to operating overhead, mainly regulatory costs, so operating below 100% power is not economically viable for very long.[citation needed] The fraction of the reactor's fuel core replaced during refueling is typically one-third, but depends on how long the plant operates between refueling. Plants typically operate on 18 month refueling cycles, or 24 month refueling cycles. This means that one refueling, replacing only one-third of the fuel, can keep a nuclear reactor at full power for nearly two years.[citation needed]

The disposition and storage of this spent fuel is one of the most challenging aspects of the operation of a commercial nuclear power plant. This nuclear waste is highly radioactive and its toxicity presents a danger for thousands of years.[90] After being discharged from the reactor, spent nuclear fuel is transferred to the on-site spent fuel pool. The spent fuel pool is a large pool of water that provides cooling and shielding of the spent nuclear fuel as well as limit radiation exposure to on-site personnel. Once the energy has decayed somewhat (approximately five years), the fuel can be transferred from the fuel pool to dry shielded casks, that can be safely stored for thousands of years. After loading into dry shielded casks, the casks are stored on-site in a specially guarded facility in impervious concrete bunkers. On-site fuel storage facilities are designed to withstand the impact of commercial airliners, with little to no damage to the spent fuel. An average on-site fuel storage facility can hold 30 years of spent fuel in a space smaller than a football field.[citation needed]

Not all reactors need to be shut down for refueling; for example, pebble bed reactors, RBMK reactors, molten-salt reactors, Magnox, AGR and CANDU reactors allow fuel to be shifted through the reactor while it is running. In a CANDU reactor, this also allows individual fuel elements to be situated within the reactor core that are best suited to the amount of U-235 in the fuel element.

The amount of energy extracted from nuclear fuel is called its burnup, which is expressed in terms of the heat energy produced per initial unit of fuel weight. Burnup is commonly expressed as megawatt days thermal per metric ton of initial heavy metal.

## Nuclear safety

[edit]

Main article: Nuclear safety

See also: Nuclear reactor safety system

Nuclear safety covers the actions taken to prevent nuclear and radiation accidents and incidents or to limit their consequences. The nuclear power industry has improved the safety and performance of reactors, and has proposed new, safer (but generally untested) reactor designs but there is no guarantee that the reactors will be designed, built and operated correctly.[111] Mistakes do occur and the designers of reactors at Fukushima in Japan did not anticipate that a tsunami generated by an earthquake would disable the backup systems that were supposed to stabilize the reactor after the earthquake,[112] despite multiple warnings by the NRG and the Japanese nuclear safety administration.[citation needed] According to UBS AG, the Fukushima I nuclear accidents have cast doubt on whether even an advanced economy like Japan can master nuclear safety.[113] Catastrophic scenarios involving terrorist attacks are also conceivable.[111] An interdisciplinary team from MIT has estimated that given the expected growth of nuclear power from 2005 to 2055, at least four serious nuclear accidents would be expected in that period.[114]

## Nuclear accidents

[edit]

See also: Lists of nuclear disasters and radioactive incidents

Three of the reactors at Fukushima I overheated, causing the coolant water to dissociate and led to the hydrogen explosions. This along with fuel meltdowns released large amounts of radioactive material into the air.[115]

Serious, though rare, nuclear and radiation accidents have occurred. These include the Windscale fire (October 1957), the SL-1 accident (1961), the Three Mile Island accident (1979), Chernobyl disaster (April 1986), and the Fukushima Daiichi nuclear disaster (March 2011).[116] Nuclear-powered submarine mishaps include the K-19 reactor accident (1961),[117] the K-27 reactor accident (1968),[118] and the K-431 reactor accident (1985).[116]

Nuclear reactors have been launched into Earth orbit at least 34 times. A number of incidents connected with the unmanned nuclear-reactor-powered Soviet RORSAT especially Kosmos 954 radar satellite which resulted in nuclear fuel reentering the Earth's atmosphere from orbit and being dispersed in northern Canada (January 1978).

## Natural nuclear reactors

[edit]

Main article: Natural nuclear fission reactor

Almost two billion years ago a series of self-sustaining nuclear fission "reactors" self-assembled in the area now known as Oklo in Gabon, West Africa. The conditions at that place and time allowed a natural nuclear fission to occur with circumstances that are similar to the conditions in a constructed nuclear reactor.[119] Fifteen fossil natural fission reactors have so far been found in three separate ore deposits at the Oklo uranium mine in Gabon. First discovered in 1972 by French physicist Francis Perrin, they are collectively known as the Oklo Fossil Reactors. Self-sustaining nuclear fission reactions took place in these reactors approximately 1.5 billion years ago, and ran for a few hundred thousand years, averaging 100 kW of power output during that time.[120] The concept of a natural nuclear reactor was theorized as early as 1956 by Paul Kuroda at the University of Arkansas.[121][122]

Such reactors can no longer form on Earth in its present geologic period. Radioactive decay of formerly more abundant uranium-235 over the time span of hundreds of millions of years has reduced the proportion of this naturally occurring fissile isotope to below the amount required to sustain a chain reaction with only plain water as a moderator.

The natural nuclear reactors formed when a uranium-rich mineral deposit became inundated with groundwater that acted as a neutron moderator, and a strong chain reaction took place. The water moderator would boil away as the reaction increased, slowing it back down again and preventing a meltdown. The fission reaction was sustained for hundreds of thousands of years, cycling on the order of hours to a few days.

These natural reactors are extensively studied by scientists interested in geologic radioactive waste disposal. They offer a case study of how radioactive isotopes migrate through the Earth's crust. This is a significant area of controversy as opponents of geologic waste disposal fear that isotopes from stored waste could end up in water supplies or be carried into the environment.

## Emissions

[edit]

Nuclear reactors produce tritium as part of normal operations, which is eventually released into the environment in trace quantities.

As an isotope of hydrogen, tritium (T) frequently binds to oxygen and forms T2O. This molecule is chemically identical to H2O and so is both colorless and odorless, however the additional neutrons in the hydrogen nuclei cause the tritium to undergo beta decay with a half-life of 12.3 years. Despite being measurable, the tritium released by nuclear power plants is minimal. The United States NRC estimates that a person drinking water for one year out of a well contaminated by what they would consider to be a significant tritiated water spill would receive a radiation dose of 0.3 millirem.[123] For comparison, this is an order of magnitude less than the 4 millirem a person receives on a round trip flight from Washington, D.C. to Los Angeles, a consequence of less atmospheric protection against highly energetic cosmic rays at high altitudes.[123]

The amounts of strontium-90 released from nuclear power plants under normal operations is so low as to be undetectable above natural background radiation. Detectable strontium-90 in ground water and the general environment can be traced to weapons testing that occurred during the mid-20th century (accounting for 99% of the Strontium-90 in the environment) and the Chernobyl accident (accounting for the remaining 1%).[124]

## See also

[edit]

* List of nuclear reactors
* List of small modular reactor designs
* List of United States Naval reactors
* Neutron transport
* Nuclear decommissioning
* Nuclear power by country
* Nuclear power in space
* One Less Nuclear Power Plant
* Radioisotope thermoelectric generator
* Safety engineering
* Sayonara Nuclear Power Plants
* Small modular reactor
* Thorium-based nuclear power
* Traveling-wave reactor (TWR)
* World Nuclear Industry Status Report
* Nuclear microreactor

## Notes

[edit]

1. ^ An extinct natural nuclear fission reactor was discovered in 1972 in Oklo, Gabon.[3]
2. ^ JEEP was constructed jointly by the Norwegian NTNF and the Dutch FOM [nl]

## References

[edit]

1. ^ "Nuclear Fuel Cycle Overview". World Nuclear Association. 20 May 2024. Retrieved 4 November 2024.
2. ^ Science and Mathematics Education Research Group, University of British Columbia. "Physics Nuclear Physics: Nuclear Reactors" (PDF). Retrieved 4 November 2024.
3. ^ Davis, E. D.; Gould, C. R.; Sharapov, E. I. (2014). "Oklo reactors and implications for nuclear science". International Journal of Modern Physics E. 23 (4): 1430007–236\. arXiv:1404.4948. Bibcode:2014IJMPE..2330007D. doi:10.1142/S0218301314300070. ISSN 0218-3013. S2CID 118394767.
4. ^ a b The First Reactor, U.S. Atomic Energy Commission, Division of Technical Information
5. ^ a b Region, CountryBy TypeBy (29 August 2024). "In Operation & Suspended Operation". PRIS. Retrieved 30 August 2024.
6. ^ Nuclear Engineering International: Obninsk - number one, by Lev Kotchetkov Archived 2 November 2013 at the Wayback Machine, who was there at the time. Source for most of the information in this article.
7. ^ "Spent Fuel Reprocessing Options" (PDF). IAEA. Retrieved 30 August 2024.
8. ^ "PRIS – Home". pris.iaea.org. Archived from the original on 11 February 2012. Retrieved 10 April 2019.
9. ^ "RRDB Search". nucleus.iaea.org. Archived from the original on 18 September 2010. Retrieved 6 January 2019.
10. ^ Oldekop, W. (1982), "Electricity and Heat from Thermal Nuclear Reactors", Primary Energy, Berlin, Heidelberg: Springer Berlin Heidelberg, pp. 66–91, doi:10.1007/978-3-642-68444-9_5, ISBN 978-3-540-11307-2, archived from the original on 5 June 2018, retrieved 2 February 2021
11. ^ "Nuclear-Powered Ships". World Nuclear Association. 15 February 2023. Retrieved 31 December 2024.
12. ^ "Nuclear Power in the World Today". World Nuclear Association. 6 January 2025. Retrieved 12 January 2025.
13. ^ Ambrose, Jillian (7 May 2024). "Renewable energy passes 30% of world's electricity supply". the Guardian. Retrieved 12 January 2025.
14. ^ "DOE Fundamentals Handbook: Nuclear Physics and Reactor Theory" (PDF). US Department of Energy. Archived from the original (PDF) on 23 April 2008. Retrieved 24 September 2008.
15. ^ "Reactor Protection & Engineered Safety Feature Systems". The Nuclear Tourist. Archived from the original on 22 August 2018. Retrieved 25 September 2008.
16. ^ "Bioenergy Conversion Factors". Bioenergy.ornl.gov. Archived from the original on 27 September 2011. Retrieved 18 March 2011.
17. ^ Bernstein, Jeremy (2008). Nuclear Weapons: What You Need to Know. Cambridge University Press. p. 312. ISBN 978-0-521-88408-2. Retrieved 17 March 2011.
18. ^ "How nuclear power works". HowStuffWorks.com. 9 October 2000. Archived from the original on 22 October 2019. Retrieved 25 September 2008.
19. ^ a b "Reactor Protection & Engineered Safety Feature Systems". The Nuclear Tourist. Archived from the original on 22 August 2018. Retrieved 25 September 2008.
20. ^ "Chernobyl: what happened and why? by CM Meyer, technical journalist" (PDF). Archived from the original (PDF) on 11 December 2013.
21. ^ Tsetkov, Pavel; Usman, Shoaib (2011). Krivit, Steven (ed.). Nuclear Energy Encyclopedia: Science, Technology, and Applications. Hoboken, NJ: Wiley. pp. 48, 85. ISBN 978-0-470-89439-2.
22. ^ "PRIS – Miscellaneous reports – Operational by Age". IAEA Power Reactor Information System – operational by age. Retrieved 12 July 2024.
23. ^ How Long Can a Nuclear Reactor Last? Archived 2 February 2017 at the Wayback Machine Paul Voosen, Scientific American, 20 Nov 2009
24. ^ Status of Subsequent License Renewal Applications. Archived 21 January 2018 at the Wayback Machine NRC, 24 Feb 2022
25. ^ What's the Lifespan for a Nuclear Reactor? Much Longer Than You Might Think Archived 9 June 2020 at the Wayback Machine. Office of Nuclear Energy, 16 Apr 2020
26. ^ "Swedish nuclear reactors shut down over safety concerns". Wikinews. 5 August 2006. Archived from the original on 16 May 2023. Retrieved 16 May 2023.
27. ^ The True Lifespan of a Nuclear Power Plant Archived 19 February 2023 at the Wayback Machine. Seacoast Anti-Pollution League (SAPL), 2017
28. ^ IAEA. Cleanup of Large Areas Contaminated as a Result of a Nuclear Accident.
29. ^ Extending the operating lives of Advanced Gas-cooled Reactors Archived 19 February 2023 at the Wayback Machine. EDF Energy
30. ^ Nuclear decommissioning Archived 19 February 2023 at the Wayback Machine. EDF (accessed Feb 2023)
31. ^ Lifetime extension of ageing nuclear power plants: Entering a new era of risk. Archived 15 March 2023 at the Wayback Machine Greenpeace, March, 2014 (2.6 MB). In German
32. ^ L. Szilárd, "Improvements in or relating to the transmutation of chemical elements," Archived 21 June 2008 at the Wayback Machine. British patent number: GB630726 (filed: 28 June 1934; published: 30 March 1936).
33. ^ Enrico, Fermi and Leo, Szilard U.S. patent 2,708,656 "Neutronic Reactor" issued 17 May 1955
34. ^ "Chicago Pile reactors create enduring research legacy – Argonne's Historical News Releases". anl.gov. Archived from the original on 13 June 2022. Retrieved 21 August 2013.
35. ^ Experimental Breeder Reactor 1 factsheet, Idaho National Laboratory Archived 29 October 2008 at the Wayback Machine
36. ^ "Fifty years ago in December: Atomic reactor EBR-I produced first electricity" (PDF). American Nuclear Society Nuclear news. November 2001. Archived from the original (PDF) on 25 June 2008. Retrieved 18 June 2008.
37. ^ "The Nuclear Option — NOVA | PBS". www.pbs.org. 11 January 2017. Archived from the original on 3 September 2017. Retrieved 12 January 2017.
38. ^ Kragh, Helge (1999). Quantum Generations: A History of Physics in the Twentieth Century. Princeton NJ: Princeton University Press. p. 286. ISBN 0-691-09552-3.
39. ^ "On This Day: 17 October". BBC News. 17 October 1956. Archived from the original on 27 October 2019. Retrieved 9 November 2006.
40. ^ Leskovitz, Frank J. "Science Leads the Way". Camp Century, Greenland. Archived from the original on 29 August 2010. Retrieved 9 September 2008.
41. ^ Reed, Bruce Cameron (2020). "Piles and Secret Cities". Manhattan Project. Cham: Springer International Publishing. pp. 149–169\. doi:10.1007/978-3-030-45734-1_5. ISBN 978-3-030-45733-4.
42. ^ Reed, B. Cameron (2021). "An inter-country comparison of nuclear pile development during World War II". The European Physical Journal H. 46 (1): 15. arXiv:2001.09971. Bibcode:2021EPJH...46...15R. doi:10.1140/epjh/s13129-021-00020-x. ISSN 2102-6459.
43. ^ Reed, B. Cameron (2021). "An inter-country comparison of nuclear pile development during World War II". The European Physical Journal H. 46 (1): 15. arXiv:2001.09971. Bibcode:2021EPJH...46...15R. doi:10.1140/epjh/s13129-021-00020-x. ISSN 2102-6459.
44. ^ Nuclear reactors built, being built, or planned 1993 (Report). Office of Scientific and Technical Information (OSTI). 1 August 1993. doi:10.2172/10141005. OSTI 10141005.
45. ^ Reed, B. Cameron (2021). "An inter-country comparison of nuclear pile development during World War II". The European Physical Journal H. 46 (1): 15. arXiv:2001.09971. Bibcode:2021EPJH...46...15R. doi:10.1140/epjh/s13129-021-00020-x. ISSN 2102-6459.
46. ^ "Manhattan Project: Places > Metallurgical Laboratory > CP-2 and CP-3". OSTI.GOV. Retrieved 25 December 2024.
47. ^ Nuclear reactors built, being built, or planned 1993 (Report). Office of Scientific and Technical Information (OSTI). 1 August 1993. doi:10.2172/10141005. OSTI 10141005.
48. ^ "Timeline". Nuclear Museum. 3 June 1920. Retrieved 7 November 2024.
49. ^ Reed, B. Cameron (2021). "An inter-country comparison of nuclear pile development during World War II". The European Physical Journal H. 46 (1): 15. arXiv:2001.09971. Bibcode:2021EPJH...46...15R. doi:10.1140/epjh/s13129-021-00020-x. ISSN 2102-6459.
50. ^ Klein, Steven; Kimpland, Robert (28 May 2014). Discussion Regarding Aqueous Homogeneous Reactor (AHR) Benchmarks (Report). doi:10.2172/1133322. Retrieved 30 December 2024.
51. ^ a b c "Plutonium: The First 50 Years". FAS Project on Government Secrecy (1991-2021). 30 September 1994. Retrieved 24 December 2024.
52. ^ Kimpland, Robert; Grove, Travis; Jaegers, Peter; Malenfant, Richard; Myers, William (3 December 2021). "Critical Assemblies: Dragon Burst Assembly and Solution Assemblies". Nuclear Technology. 207 (sup1): S81 – S99. arXiv:2103.05780. Bibcode:2021NucTe.207S..81K. doi:10.1080/00295450.2021.1927626. ISSN 0029-5450.
53. ^ "ZEEP -- Canada's First Nuclear Reactor". Canada Science and Technology Museum. Archived from the original on 6 March 2014.
54. ^ Patenaude, Hannah K.; Freibert, Franz J. (9 March 2023). "Oh, My Darling Clementine: A Detailed History and Data Repository of the Los Alamos Plutonium Fast Reactor". Nuclear Technology. 209 (7). Informa UK Limited: 963–1007\. Bibcode:2023NucTe.209..963P. doi:10.1080/00295450.2023.2176686. ISSN 0029-5450.
55. ^ Hurst, D.G. (1997). Canada Enters the Nuclear Age: A Technical History of Atomic Energy of Canada Limited as Seen from Its Research Laboratories. McGill-Queen's University Press. p. 45\. ISBN 978-0-7735-6653-8. Retrieved 31 December 2024.
56. ^ Hill, C (2013). An Atomic Empire: A Technical History of the Rise and Fall of the British Atomic Energy Programme. Imperial College Press. ISBN 978-1-908977-41-0.
57. ^ Diakov, Anatoli (25 April 2011). "The History of Plutonium Production in Russia". Science & Global Security. 19 (1): 28–45\. Bibcode:2011S&GS...19...28D. doi:10.1080/08929882.2011.566459. ISSN 0892-9882.
58. ^ "Magnox BEPO reactor 75th Anniversary". GOV.UK. 3 July 2023. Retrieved 13 January 2025.
59. ^ "Irène and Frédéric Joliot-Curie". Institut Curie. Archived from the original on 3 June 2010. Retrieved 26 April 2010.
60. ^ "ФКБН / Сводный указатель объектов / Атомный проект СССР // Электронная библиотека /// История Росатома". Электронная библиотека /// История Росатома (in Russian). Retrieved 10 January 2025.
61. ^ Loffe, B. L.; Shvedov, O. V. (1999). "Heavy water reactors and nuclear power plants in the USSR and Russia: Past, present, and future". Atomic Energy. 86 (4): 295–304\. doi:10.1007/BF02673145. ISSN 1063-4258.
62. ^ Reed, Bruce Cameron (2020). "Piles and Secret Cities". Manhattan Project. Cham: Springer International Publishing. pp. 149–169\. doi:10.1007/978-3-030-45734-1_5. ISBN 978-3-030-45733-4.
63. ^ "Shippingport". World Nuclear Association. 1 May 1955. Retrieved 4 January 2025.
64. ^ "ZEEP -- Canada's First Nuclear Reactor". Canada Science and Technology Museum. Archived from the original on 6 March 2014.
65. ^ "Rolphton NPD". World Nuclear Association. 1 January 1958. Retrieved 4 January 2025.
66. ^ Vakhroucheva, Elizaveta. "Division of System Analysis Elektronika Information and Computer Complex Engineering and Production Division". Kurchatov Institute. NTI. Archived from the original on 15 January 2009. Retrieved 25 December 2010.
67. ^ "APS 1 Obninsk". World Nuclear Association. 1 January 1951. Retrieved 4 January 2025.
68. ^ Hill, C (2013). An Atomic Empire: A Technical History of the Rise and Fall of the British Atomic Energy Programme. Imperial College Press. ISBN 978-1-908977-41-0.
69. ^ "Calder Hall 1". World Nuclear Association. 1 August 1953. Retrieved 4 January 2025.
70. ^ "Irène and Frédéric Joliot-Curie". Institut Curie. Archived from the original on 3 June 2010. Retrieved 26 April 2010.
71. ^ "G 2 (Marcoule)". World Nuclear Association. 1 March 1955. Retrieved 4 January 2025.
72. ^ Splunter, J.M. van. (1994). "Love at first sight. Co-operation between the Netherlands and Norway on the peaceful use of atomic energy, 1950-1960". INIS. Retrieved 4 January 2025.
73. ^ Blomstrand, Edward (1 February 2005). "Swedish nuclear power. A review of the legislation in the nuclear energy field from the second world war til the new millennium; Svensk kaernenergi. En expose oever lagstiftningen paa kaernenergiomraadet fraan andra vaerldskriget till millennieskiftet". OSTI.GOV. Retrieved 5 January 2025.
74. ^ "Agesta". World Nuclear Association. 1 December 1957. Retrieved 4 January 2025.
75. ^ Domain, Research (25 April 2016). "Belgian Reactor 1 / Research facilities / Science Platform". science.sckcen.be. Archived from the original on 25 June 2016. Retrieved 6 January 2025.
76. ^ "BR-3". World Nuclear Association. 1 November 1957. Retrieved 6 January 2025.
77. ^ "Apsara Research Reactor". Archived from the original on 19 April 2015. Retrieved 12 April 2015.
78. ^ "Tarapur 1". World Nuclear Association. 1 October 1964. Retrieved 4 January 2025.
79. ^ Trischler, Helmuth (31 December 2004). "Nationales Innovationssystem und regionale Innovationspolitik". Politik und Kultur im föderativen Staat 1949 bis 1973. OLDENBOURG WISSENSCHAFTSVERLAG. p. 156\. doi:10.1524/9783486708646.117. ISBN 978-3-486-56596-6.
80. ^ "VAK Kahl". World Nuclear Association. 1 July 1958. Retrieved 4 January 2025.
81. ^ "Die Geschichte des HZDR im Überblick". Helmholtz-Zentrum Dresden-Rossendorf, HZDR. 18 April 1955. Retrieved 10 May 2025.
82. ^ "Rheinsberg". World Nuclear Association. 1 January 1960. Retrieved 10 May 2025.
83. ^ Frank, Lewis A. (1966). "Nuclear Weapons Development in China". Bulletin of the Atomic Scientists. 22 (1): 12–15\. Bibcode:1966BuAtS..22a..12F. doi:10.1080/00963402.1966.11454882. ISSN 0096-3402.
84. ^ "Qinshan 1". World Nuclear Association. 20 March 1985. Retrieved 4 January 2025.
85. ^ "Scorie a riposo. ISPRA-1, il primo reattore nucleare italiano | Il Bo Live UniPD". ilbolive.unipd.it (in Italian). 18 July 2022. Retrieved 25 April 2025.
86. ^ a b c "Nuclear Power Reactors in the World – 2015 Edition" (PDF). International Atomic Energy Agency (IAEA). Archived (PDF) from the original on 16 November 2020. Retrieved 26 October 2017.
87. ^ Golubev, V. I.; Dolgov, V. V.; Dulin, V. A.; Zvonarev, A. V.; Smetanin, É. Y.; Kochetkov, L. A.; Korobeinikov, V. V.; Liforov, V. G.; Manturov, G. N.; Matveenko, I. P.; Tsibulya, A. M. (1993). "Fast-reactor actinoid transmutation". Atomic Energy. 74: 83. doi:10.1007/BF00750983. S2CID 95704617.
88. ^ a b Nave, R. "Light Water Nuclear Reactors". Hyperphysics. Georgia State University. Archived from the original on 3 December 2017. Retrieved 5 March 2018.
89. ^ Joyce, Malcolm (2018). "10.6". Nuclear Engineering. Elsevier. doi:10.1016/c2015-0-05557-5. ISBN 9780081009628.
90. ^ a b Lipper, Ilan; Stone, Jon. "Nuclear Energy and Society". University of Michigan. Archived from the original on 1 April 2009. Retrieved 3 October 2009.
91. ^ "Pool Reactors 1: An Introduction – ANS / Nuclear Newswire". Archived from the original on 6 November 2021. Retrieved 6 November 2021.
92. ^ "Emergency and Back-Up Cooling of Nuclear Fuel and Reactors and Fire-Extinguishing, Explosion Prevention Using Liquid Nitrogen". USPTO Patent Applications. Document number 20180144836. 24 May 2018.
93. ^ "Russia completes world's first Gen III+ reactor; China to start up five reactors in 2017". Nuclear Energy Insider. 8 February 2017. Archived from the original on 13 August 2020. Retrieved 10 July 2019.
94. ^ a b Generation IV Nuclear Reactors Archived 30 March 2023 at the Wayback Machine. World Nuclear Association, update Dec 2020
95. ^ Nucleonics Week, Vol. 44, No. 39; p. 7, 25 September 2003 Quote: "Etienne Pochon, CEA director of nuclear industry support, outlined EPR's improved performance and enhanced safety features compared to the advanced Generation II designs on which it was based."
96. ^ "Generation IV". Euronuclear.org. Archived from the original on 17 March 2011. Retrieved 18 March 2011.
97. ^ "A Technology Roadmap for Generation IV Nuclear Energy Systems" (PDF). Archived from the original (PDF) on 5 October 2006. Retrieved 5 March 2007. (4.33 MB); see "Fuel Cycles and Sustainability"
98. ^ "World Nuclear Association Information Brief – Research Reactors". Archived from the original on 31 December 2006. Retrieved 3 May 2007.
99. ^ "HTR-PM: Making dreams come true". Nuclear Engineering International. Archived from the original on 28 March 2022. Retrieved 12 December 2019.
100. ^ "RRDB Search". nucleus.iaea.org. Archived from the original on 12 May 2019. Retrieved 6 January 2019.
101. ^ "Advanced Nuclear Power Reactors". World Nuclear Association. Archived from the original on 6 February 2010. Retrieved 29 January 2010.
102. ^ Till, Charles. "Nuclear Reaction: Why Do Americans Fear Nuclear Power?". Public Broadcasting Service (PBS). Archived from the original on 17 April 2018. Retrieved 9 November 2006.
103. ^ Juhasz, Albert J.; Rarick, Richard A.; Rangarajan, Rajmohan (October 2009). "High Efficiency Nuclear Power Plants Using Liquid Fluoride Thorium Reactor Technology" (PDF). NASA. Archived (PDF) from the original on 28 April 2021. Retrieved 27 October 2014.
104. ^ "The Venezuela-China relationship, explained: Belt and Road | Part 2 of 4". SupChina. 14 January 2019. Archived from the original on 24 June 2019. Retrieved 24 June 2019.
105. ^ "Rolls-Royce Touts Nuclear Reactors as Key to Clean Jet Fuel". Bloomberg News. Archived from the original on 19 December 2019. Retrieved 19 December 2019.
106. ^ De Clercq, Geert (13 October 2014). "Can Sodium Save Nuclear Power?". Scientific American. Archived from the original on 29 July 2021. Retrieved 10 August 2022.
107. ^ "Generation IV Nuclear Reactors". World Nuclear Association. Archived from the original on 23 January 2010. Retrieved 29 January 2010.
108. ^ "International Scientific Journal for Alternative Energy and Ecology, DIRECT CONVERSION OF NUCLEAR ENERGY TO ELECTRICITY, Mark A. Prelas" (PDF). Archived from the original (PDF) on 4 March 2016. Retrieved 7 December 2013.
109. ^ Quimby, D.C., High Thermal Efficiency X-ray energy conversion scheme for advanced fusion reactors, ASTM Special technical Publication, v.2, 1977, pp. 1161–1165
110. ^ "Improving Security at World's Nuclear Research Reactors: Technical and Other Issues Focus of June Symposium in Norway". IAEA. 7 June 2006. Archived from the original on 14 August 2007. Retrieved 3 August 2007.
111. ^ a b Jacobson, Mark Z. & Delucchi, Mark A. (2010). "Providing all Global Energy with Wind, Water, and Solar Power, Part I: Technologies, Energy Resources, Quantities and Areas of Infrastructure, and Materials" (PDF). Energy Policy. p. 6.[dead link]
112. ^ Gusterson, Hugh (16 March 2011). "The lessons of Fukushima". Bulletin of the Atomic Scientists. Archived from the original on 6 June 2013.
113. ^ Paton, James (4 April 2011). "Fukushima Crisis Worse for Atomic Power Than Chernobyl, UBS Says". Bloomberg Businessweek. Archived from the original on 15 May 2011.
114. ^ Massachusetts Institute of Technology (2003). "The Future of Nuclear Power" (PDF). p. 48\. Archived (PDF) from the original on 12 April 2019. Retrieved 15 June 2011.
115. ^ Fackler, Martin (1 June 2011). "Report Finds Japan Underestimated Tsunami Danger". The New York Times.
116. ^ a b The Worst Nuclear Disasters. Time.
117. ^ Strengthening the Safety of Radiation Sources Archived 11 January 2015 at the Wayback Machine p. 14.
118. ^ Johnston, Robert (23 September 2007). "Deadliest radiation accidents and other events causing radiation casualties". Database of Radiological Incidents and Related Events. Archived from the original on 23 October 2007. Retrieved 27 June 2011.
119. ^ Video of physics lecture – at Google Video; a natural nuclear reactor is mentioned at 42:40 mins into the video Archived 4 August 2006 at the Wayback Machine
120. ^ Meshik, Alex P. (November 2005) "The Workings of an Ancient Nuclear Reactor." Archived 15 March 2015 at the Wayback Machine Scientific American. p. 82.
121. ^ "Oklo: Natural Nuclear Reactors". Office of Civilian Radioactive Waste Management. Archived from the original on 16 March 2006. Retrieved 28 June 2006.
122. ^ "Oklo's Natural Fission Reactors". American Nuclear Society. Archived from the original on 30 March 2021. Retrieved 28 June 2006.
123. ^ a b Backgrounder: Tritium, Radiation Protection Limits, and Drinking Water Standards (PDF) (Report). United States Nuclear Regulatory Commission. February 2016. Archived (PDF) from the original on 18 August 2017. Retrieved 17 August 2017.
124. ^ "Radionuclides in Groundwater". U.S. NRC. nrc.gov. Archived from the original on 2 October 2017. Retrieved 2 October 2017.

## External links

[edit]

Wikimedia Commons has media related to Nuclear reactors.

* The Database on Nuclear Power Reactors – IAEA. Archived 2 June 2013 at the Wayback Machine
* Uranium Conference adds discussion of Japan accident
* A Debate: Is Nuclear Power The Solution to Global Warming?
* Union of Concerned Scientists, Concerns re: US nuclear reactor program
* Freeview Video 'Nuclear Power Plants – What's the Problem' A Royal Institution Lecture by John Collier by the Vega Science Trust. Archived 3 November 2011 at the Wayback Machine
* Nuclear Energy Institute – How it Works: Electric Power Generation. Archived 30 January 2010 at the Wayback Machine
* Annotated bibliography of nuclear reactor technology from the Alsos Digital Library
* (in Japanese) ソヴィエト連邦における宇宙用原子炉の開発とその実用. Archived 3 June 2019 at the Wayback Machine

* v
* t
* e

Nuclear technology

* Outline

| Science|

* Chemistry
* Engineering
* Physics
* Atomic nucleus
* Fission
* Fusion
* Radiation
* ionizing
* braking

|

Fuel|

* Tritium
* Deuterium
* Helium-3
* Fertile material
* Fissile material
* Isotope separation
* Nuclear material
* Uranium
* enriched
* depleted
* Plutonium
* Thorium

Neutron|

* Activation
* Capture
* Poison
* Cross section
* Generator
* Radiation
* Wigner effect
* Reflector
* Temperature
* Thermal
* Fast
* Fusion

Power|

* by country
* Power plant
* Economics
* Accidents and incidents
* Policy
* Fusion
* Radioisotope thermoelectric (RTG)
* MMRTG
* Propulsion
* rocket
* Safety and security
* Nuclear meltdown

Medicine|

| Imaging|

* Autoradiograph
* RadBall
* Scintigraphy
* Single-photon emission (SPECT)
* Positron-emission tomography (PET)

|

Therapy|

* Fast-neutron
* Neutron capture therapy of cancer
* Targeted alpha-particle
* Proton-beam
* Tomotherapy
* Brachytherapy
* Radiosurgery
* Radiopharmacology

Processing|

* Atomic gardening
* Electron-beam processing
* Food irradiation
* Gemstone irradiation

Weapons|

| Topics|

* Arms race
* Delivery
* Design
* Disarmament
* Ethics
* Explosion
* effects
* History
* Proliferation
* Testing
* high-altitude
* underground
* Warfare
* Yield
* TNTe

|

Lists|

* States with nuclear weapons
* Historical stockpiles and tests
* Tests
* Tests in the United States
* WMD treaties
* Weapon-free zones
* Weapons

Waste|

| Products|

* Actinide
* Reprocessed uranium
* Reactor-grade plutonium
* Minor actinide
* Activation
* Fission
* LLFP
* Actinide chemistry

|

Disposal|

* Fuel cycle
* High-level (HLW)
* Low-level (LLW)
* Nuclear decommissioning
* Repository
* Reprocessing
* Spent fuel
* pool
* cask
* Transmutation

Debate|

* Nuclear power
* Nuclear weapons
* Blue Ribbon Commission on America's Nuclear Future
* Anti-nuclear movement
* Uranium mining
* Nuclear power phase-out

Nuclear reactors

Fission

Moderator

Light water|

* Aqueous homogeneous
* Boiling
* BWR
* ABWR
* ESBWR
* Kerena
* Natural fission
* Pressurized
* AP1000
* APR-1400
* APR+
* APWR
* ATMEA1
* CAP1400
* CPR-1000
* EPR
* HPR-1000
* ACPR1000
* ACP1000
* VVER
* RITM-200
* KLT-40
* OK-150/OK-900
* OK-650
* KN-3
* VM
* IPWR-900
* many others
* Supercritical (SCWR)

Heavy water
by coolant|

| D2O|

* Pressurized
* CANDU
* CANDU 6
* CANDU 9
* EC6
* AFCR
* ACR-1000
* CVTR
* IPHWR
* IPHWR-220
* IPHWR-540
* IPHWR-700
* PHWR KWU
* MZFR
* R3
* R4 Marviken

|

H2O|

* HWLWR
* ATR
* HW BLWR 250
* Steam-generating (SGHWR)
* AHWR

Organic|

* WR-1

CO2|

* HWGCR
* EL-4
* KKN
* KS 150
* Lucens

Graphite
by coolant

| Water|

| H2O|

* AM-1
* AMB-X
* EGP-6
* RBMK
* MKER

|

Gas|

| CO2|

* Uranium Naturel Graphite Gaz (UNGG)
* Magnox
* Advanced gas-cooled (AGR)

|

He|

* GTMHR
* MHR-T
* UHTREX
* VHTR (HTGR)
* PBR (PBMR)
* AVR
* HTR-10
* HTR-PM
* THTR-300
* PMR

Molten-salt|

| Fluorides|

* Fuji MSR
* Liquid-fluoride thorium reactor (LFTR)
* Molten-Salt Reactor Experiment (MSRE)
* Integral Molten Salt Reactor (IMSR)
* TMSR-500
* TMSR-LF1

|

None
(fast-neutron)

* Breeder (FBR)
* Integral (IFR)
* Liquid-metal-cooled (LMFR)
* OK-550
* BM-40A
* VT-1
* Small sealed transportable autonomous (SSTAR)
* Traveling-wave (TWR)
* Energy Multiplier Module (EM2)
* Reduced-moderation (RMWR)
* Fast Breeder Test Reactor (FBTR)
* Dual fluid reactor (DFR)

Generation IV|

* Sodium (SFR)
* BN-350
* BN-600
* BN-800
* BN-1200
* CFR-600
* Phénix
* Superphénix
* PFBR
* FBR-600
* CEFR
* PFR
* PRISM
* Lead
* BREST-300
* Helium gas (GFR)
* Stable Salt Reactor (SSR)

Others|

* Organic nuclear reactor
* OMRE
* Arbus
* Piqua
* Aircraft Reactor Experiment

Fusion

by confinement

Magnetic|

* Field-reversed configuration
* Levitated dipole
* Reversed field pinch
* Spheromak
* Stellarator
* Tokamak

Inertial|

* Bubble (acoustic)
* Fusor
* electrostatic
* Laser-driven
* Magnetized-target
* Z-pinch

Other|

* Dense plasma focus
* Migma
* Muon-catalyzed
* Polywell
* Pyroelectric

* Nuclear technology portal
* Category
* Commons

* v
* t
* e

Nuclear and radioactive disasters, former facilities, tests and test sites

Lists of
disasters
and
incidents|

* Crimes involving radioactive substances
* Criticality accidents and incidents
* Nuclear meltdown accidents
* Military nuclear accidents
* Nuclear and radiation accidents and incidents
* Nuclear and radiation accidents by death toll
* Nuclear and radiation fatalities by country
* Nuclear weapons tests
* China
* France
* India
* North Korea
* Pakistan
* South Africa
* Soviet Union
* United Kingdom
* in Australia
* in the United States
* United States
* Sunken nuclear submarines
* List of orphan source incidents
* Nuclear power accidents by country

Individual
accidents
and sites|

* 2019 Nyonoksa radiation accident
* 2011 Fukushima nuclear accident
* 2001 Instituto Oncológico Nacional#Accident
* 1996 San Juan de Dios radiotherapy accident
* 1990 Clinic of Zaragoza radiotherapy accident
* 1987 Goiânia accident
* 1986 Chernobyl disaster
* Effects
* Related articles
* 1985 Chazhma Bay nuclear accident
* 1985–1987 Therac-25 accident
* 1982 Andreev Bay nuclear accident
* 1980 Kramatorsk radiological accident
* 1979 Three Mile Island accident and Three Mile Island accident health effects
* 1969 Lucens reactor
* 1962  Thor missile launch failures at Johnston Atoll under Operation Fishbowl
* 1962 Cuban Missile Crisis
* 1961 K-19 nuclear accident
* 1961 SL-1 nuclear meltdown
* 1957 Kyshtym disaster
* 1957 Windscale fire
* 1957 Operation Plumbbob
* 1954 Totskoye nuclear exercise
* Bikini Atoll
* Hanford Site
* Rocky Flats Plant
* 1945 Atomic bombings of Hiroshima and Nagasaki

Related
topics|

* International Nuclear Event Scale (INES)
* Vulnerability of nuclear plants to attack
* Books about nuclear issues
* Films about nuclear issues
* Anti-war movement
* Bikini Atoll
* Bulletin of the Atomic Scientists
* History of the anti-nuclear movement
* International Day against Nuclear Tests
* Nuclear close calls
* Nuclear-Free Future Award
* Nuclear-free zone
* Nuclear power debate
* Nuclear power phase-out
* Nuclear weapons debate
* Peace activists
* Peace movement
* Peace camp
* Russell–Einstein Manifesto
* Smiling Sun

Nuclear technology portal Category

Portals:

* Nuclear technology
* Energy

Authority control databases

National|

* Germany
* United States
* France
* BnF data
* Japan
* Czech Republic
* Israel

Other|

* NARA

*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template