Sandpaper

Abrasive material used for smoothing softer materials

"Sanding" redirects here. For the fish known as sanding, see Pseudaphritis urvillii.

This article's lead section may be too short to adequately summarize the key points. Please consider expanding the lead to provide an accessible overview of all important aspects of the article. (December 2023)

|

Sheets of sandpaper with different grit sizes (40 (coarse), 80, 150, 240, 600 (fine))

Sandpaper, also known as coated abrasive or emery paper, is a type of material that consists of sheets of paper or cloth with an abrasive substance glued to one face.[1] In the modern manufacture of these products, sand and glass have been replaced by other abrasives such as aluminium oxide or silicon carbide. It is common to use the name of the abrasive when describing the paper, e.g. "aluminium oxide paper", or "silicon carbide paper".

There are many varieties of sandpaper, with variations in the paper or backing, the material used for the grit, grit size, and the bond.

Sandpaper is produced in a range of grit sizes and is used to remove material from surfaces, whether to make them smoother (for example, in painting and wood finishing), to remove a layer of material (such as old paint), or sometimes to make the surface rougher (for example, as a preparation for gluing). The grit size of sandpaper is usually stated as a number that is inversely related to the particle size. A small number such as 20 or 40 indicates a coarse grit, while a large number such as 1500 indicates a fine grit.

## History

[edit]

The first recorded instance of sandpaper was in 13th-century China when crushed shells, seeds, and sand were bonded to parchment using natural gum.[2][3]

Shark skin (placoid scales) has also been used as an abrasive, and the rough scales of the Coelacanth are used for the same purpose by the natives of Comoros.[4] Boiled and dried, the rough horsetail plant is used in Japan as a traditional polishing material, finer than sandpaper.

Cheap sandpaper was often passed off as glass paper; Stalker and Parker cautioned against it in A Treatise of Japaning and Varnishing published in 1688.[5]

Glass paper was manufactured in London in 1833 by John Oakey, whose company had developed new adhesive techniques and processes, enabling mass production. Glass frit has sharp-edged particles and cuts well whereas sand grains are smoothed down and do not work well as an abrasive.

In 1921, 3M invented a sandpaper with silicon carbide grit and a waterproof adhesive and backing, known as Wet and dry. This allowed use with water, which would serve as a lubricant to carry away particles that would otherwise clog the grit. Its first application was in automotive paint refinishing.[6]

## Backing

[edit]

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (April 2022) (Learn how and when to remove this message)

|

320 grit silicon carbide sandpaper, with close-up view

In addition to paper, backing for sandpaper includes cloth (cotton, polyester, rayon), PET film, "fibre", and rubber. Cloth backing is used for sandpaper discs and belts, while PET film is used as backing for extremely fine grits. Fibre or vulcanized fibre is a strong backing material consisting of many layers of polymer impregnated paper. The weight of the backing is usually designated by a letter. For paper backings, the weight ratings range from "A" to "F", with A designating the lightest and F the heaviest. Letter nomenclature follows a different system for cloth backings, with the weight of the backing rated J, X, Y, T, and M, from lightest to heaviest. A flexible backing allows sandpaper to follow irregular contours of a workpiece; relatively inflexible backing is optimal for regular rounded or flat surfaces. Sandpaper backings may be glued to the paper or form a separate support structure for moving sandpaper, such as used in sanding belts and discs. Stronger paper or backing increases the ease of sanding wood. The harder the backing material, the faster the sanding, the faster the wear of the paper and the rougher the sanded surface.

## Fitting

[edit]

Examples of sanding discs using a quick-change mounting system

A quick-change system is commonly used with disc-type coated abrasives. A plastic or metal hub is bonded to one of the faces, which is threaded. This then mates directly to the sander or angle grinder or to a mandrel that can be mounted in a sander, grinder, or drill. The advantage is that the disc can be quickly replaced when needed. Quick-change discs are available in sizes of about 50 millimetres (2.0 in) and larger.

## Abrasives

[edit]

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (April 2022) (Learn how and when to remove this message)

|

Emery cloth sheet whose component abrasive is aluminium oxide Assorted coated abrasives

Common substrates are paper, cloth, vulcanized fiber, and plastic films and come in grit sizes range from very coarse (≈2 mm) to ultrafine (submicrometre). The international standard for coated abrasives is ISO 6344. Sandpaper and emery cloth are coated abrasives for hand use, usually non-precision. Other coated abrasive forms include sanding cords, pads, belts, and discs. Variants are available for use by hand or as components for power tools such as sanders, die grinders and belt sanders.

Types of abrasive materials include:

* Glass: No longer commonly used.
* Flint: No longer commonly used.
* Garnet: Commonly used in woodworking.
* Emery: Commonly used to abrade or polish metals.
* Aluminium oxide: The most common in modern use, with the widest variety of grits, lowest unit cost; can be used on metal (i.e. body shops) or wood.
* Silicon carbide: Available in very coarse grits all the way through to microgrits, common in wet applications.
* Alumina-zirconia: (An aluminium oxide–zirconium oxide alloy), used for machine grinding applications.
* Chromium(III) oxide: Used in extremely fine micron grit (micrometre level) papers.
* Diamond: Used for finishing and polishing hard metals, ceramics and glass.
* Ceramic aluminium oxide: Used in high pressure applications, used in both coated abrasives, as well as in bonded abrasives.

Sandpaper may be "stearated" where a dry lubricant is loaded to the abrasive. Stearated papers are useful in sanding coats of finish and paint as the stearate "soap" prevents clogging and increases the useful life of the sandpaper.

The harder the grit material, the easier the sanding of harder surfaces like hardwoods such as hickory, pecan, or wenge. The grit material for polishing granite must be harder than granite.

### Emery

[edit]

320 grit emery cloth

Emery cloth is a type of coated abrasive that has emery glued to a cloth backing. It is used for hand metalworking. It may be sold in sheets or in narrow rolls, typically 25 or 50 mm wide, often described as "emery tape". The cloth backing makes emery cloth stronger in tension than paper, but still allows a sheet to be conveniently torn to size. Emery (largely displaced by improved products such as aluminium oxide and silicon carbide) is used for scrubbing highly abraded and rough surfaces to a smooth and shiny finish, notably in watchmaking.[7] Emery paper, more commonly seen, has a paper backing and is usually a finer grit.

Emery was considered a suitable abrasive for fitting work and the final adjustment of steel parts for a perfect fit. It had the advantage that, unlike harder abrasives, it was not considered to embed abrasive traces in the polished components afterwards. Emery was also used for cleaning, as a means of removing rust from polished steel components.

Both emery cloth and paper are still sold in hardware and do it yourself stores, but have been largely supplanted by the increased use of machine grinding to precision size, which has minimized or eliminated the need for hand-fitting; the widespread availability of powered hand tools employing sanding and grinding accessories such as flapwheels; and a shift to other forms of abrasive, such as aluminium oxide, aluminium zirconia and silicon carbide.

Emery is rated on the average grit size, glued to the backing. Common sizes are, from coarse to fine: 40, 46, 54, 60, 70, 80, 90, 100, 120, 180, 220, 320, F, and FF. A 46 or 54 grade cloth is used on roughly filed work, while 220 to 320 grit cloth will give a good polish.[8]

By the successive use of progressively finer mesh emery paper, near-mirror finishes can be obtained. Water or oil is often used as a lubricant and to float the abrasive debris and worn abrasive away from the work, preventing the build-up of debris in the emery paper. The paper will lose effectiveness if too much debris builds up, a condition known as "clogging", or "loading".

Originally, emery paper was made from milled emery rock, bonded or sized to paper often with an animal glue for water resistance.[9] Today, synthetic adhesives are used in place of natural glues and silicon carbide (SiC) is often substituted for emery, silicon carbide being slightly harder, and more durable with less tendency to fracture than corundum. The use of natural emery papers is rare today generally being replaced with silicon carbide or pure aluminium oxide papers.

Emery cloth has the abrasives bonded to a fabric instead of a paper. The cloth is more tear resistant, flexible, and costly. Emery boards have applications similar to emery paper or cloth. It also has a use in modelling. For 00 scale modelling, the fine grades of emery paper can have the appearance of a tarmac surface.

### Crocus

[edit]

Crocus cloth is an abrasive sheet similar to sandpaper or emery cloth but covered with a layer of very fine loose iron oxide particles rather than with bound grains of abrasive. It is intended for final metal and gemstone finishing and is available in various grades (particle sizes). Federal Specification P-C-458 described this material in detail, although the specification was cancelled in 1989.[10]

## Wet and dry papers

[edit]

Abrasive papers and cloths with a waterproof backing allow the use of a lubricant, typically water, which can both decapitate rough surfaces when used dry and produce a semi-polished satin type finish when wet. Super-fine grades can produce a "key" adhesion surface appropriate for spray painting in critical decorative applications such as automotive bodywork repair.[11][12]

## Bonds

[edit]

This section needs additional citations for verification. Please help improve this article by adding citations to reliable sources in this section. Unsourced material may be challenged and removed.
Find sources: "Sandpaper" – news · newspapers · books · scholar · JSTOR (September 2022) (Learn how and when to remove this message)

|

Different adhesives are used to bond the abrasive to the paper. Hide glue is still used, but this glue often cannot withstand the heat generated during machine sanding and is not waterproof. Waterproof sandpapers or wet/dry sandpapers use a resin bond and a waterproof backing.

Sandpaper can be either closed coat or open coat. Approximately 90% to 95% of the surface is covered with abrasive grains with a closed coat. Closed coat sandpaper is good for hand sanding or working with harder materials. In comparison, 50% to 70% of the surface is covered with abrasive grains with open coat sandpaper. The separation between particles makes the sandpaper more flexible, which prevents the sandpaper from clogging. However, the gaps in grit coverage limits the sandpaper's ability to perform even polishing jobs. Open coat sandpaper is better for softer materials.

Wet and dry sandpaper is more effective used wet because clogging is reduced by particles washing away from the grinding surface.[13]

## Shapes

[edit]

This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (April 2022) (Learn how and when to remove this message)

|

Sandpaper comes in a number of different shapes and sizes:

* Sheet: usually 9 by 11 inches (23 by 28 cm), but other sizes may be available
* Belt: usually cloth backed, comes in different sizes to fit different belt sanders.
* Disk: made to fit different models of disc and random orbit sanders. May be perforated for some models of sanders. Attachment includes pressure-sensitive adhesive (PSA) and "hook-and-loop" (similar to Velcro).
* Rolls: known as "shag rolls" by many contractors
* Sponge: for tight places

## Grit sizes

[edit]

This section needs additional citations for verification. Please help improve this article by adding citations to reliable sources in this section. Unsourced material may be challenged and removed.
Find sources: "Sandpaper" – news · newspapers · books · scholar · JSTOR (September 2022) (Learn how and when to remove this message)

|

Grit sizes

Grit size refers to the size of the particles of abrading materials embedded in the sandpaper. These measurements are determined by the amount of the abrasive material that can fit through a square inch filter.[14] Size of a grit is roughly equal to 2/3 inch divided by "grit size" number.[15] For example "100" grit sandpaper has particle size near 0.160 mm (= 0.0064 inch). Several standards have been established for grit size. These standards establish not only the average grit size, but also the allowable variation from the average. The two most common are the United States CAMI (Coated Abrasive Manufacturers Institute, now part of the Unified Abrasives Manufacturer's Association) and the European FEPA (Federation of European Producers of Abrasives) "P" grade.[16] The FEPA system is the same as the ISO 6344 standard. Other systems used in sandpaper include the Japanese Industrial Standards Committee (JIS), the micron grade (generally used for very fine grits). Cheaper sandpapers may sometimes only use descriptive nomenclature such as "coarse", "medium" and "fine" without referring to any standard.

## See also

[edit]

* Grain size
* Lapping film
* Rotary tool
* Sanding block
* Steel abrasive

## References

[edit]

1. ^ Hill, Ray (July 1977), "PS guide to sandpaper and other coated abrasives", Popular Science, 211 (1): 106, ISSN 0161-7370.
2. ^ Casey, Don (May 3, 2016). "Know How: Sandpapers and Sanding". Sail Magazine. Retrieved 1 February 2019.
3. ^ Parker, Jerry (April 1962), "How to choose the right coated abrasive", Popular Science, 180 (4): 159, ISSN 0161-7370.
4. ^ Thomson, Keith Stewart (1992). Living Fossil: The Story of the Coelacanth. W. W. Norton & Company Limited. ISBN 978-0-393-30868-6. Archived from the original on 2014-06-27.
5. ^ Stalker & Parker (1971) [1688]. A Treatise of Japaning and Varnishing. Tiranti.
6. ^ Jeffrey, Kirk (1989). "The Major Manufacturers: From Food and Forest Products to High Technology". In Clark, Clifford Edward (ed.). Minnesota in a Century of Change: The State And Its People Since 1900. Minnesota Historical Society Press. p. 234\. ISBN 978-0-87351-238-1. Archived from the original on 2014-06-27.
7. ^ Dwivedi, Kamal (17 June 2021). "What is Difference Between Emery Paper and Sandpaper?". Mechical. (blog). Retrieved 2023-03-10.
8. ^ Oberg, Erik; Jones, Franklin D.; Horton, Holbrook L.; Ryffel, Henry H. (2000). Machinery's Handbook (26th ed.). New York: Industrial Press Inc. p. 1440\. ISBN 0-8311-2635-3.
9. ^ Parker, John W.; Strand, West (1835). Minerals and Metals; Their Natural History and Uses in the Arts. Society for Promoting Christian Knowledge. p. 208.
10. ^ "P-C-458 C Cloth Abrasive Crocus".
11. ^ "3M™ Wetordry™ Sandpaper". Archived from the original on 2022-09-05. Retrieved 2022-09-05.
12. ^ "Abrasive Wet and Dry Paper". The Polishing Shop. Retrieved 2023-03-10.
13. ^ Stack, Jim (2006). Box by box. Cincinnati, Ohio: Popular Woodworking Books. ISBN 1558709436.
14. ^ "Sandpaper Grit". Empire Abrasives. Retrieved 13 April 2020.
15. ^ "Schleifpapier".
16. ^ "Grit Size Chart".

## Further reading

[edit]

* Dresdner, Michael (1992). The Woodfinishing Book. Taunton Press. ISBN 1-56158-037-6
* Flexner, Bob (2005). Understanding Wood Finishing — How to Select and Apply the Right Finish. Fox Chapel Publishing. ISBN Hardcover:978-1-56523-548-9. ISBN Paperback:978-1-56523-566-3

## External links

[edit]

Wikimedia Commons has media related to Sandpaper.

* Federation of European Producers of Abrasives
* sizes.com on sandpaper
* Conversion Chart Abrasives - Grit Sizes

* v
* t
* e

Cutting and abrasive tools

* Adze
* Axe
* Blade
* Bolt cutter
* Broach
* Burnisher
* Ceramic tile cutter
* Chisel
* Countersink
* Cutting tool
* Diagonal pliers
* Diamond blade
* Diamond tool
* Disc cutter
* Drawknife
* Drill bit
* Emery cloth
* File
* Froe
* Glass cutter
* Grater
* Grinding wheel
* Honing steel
* Knife
* Laser
* Lawn mower
* Machete
* Meat slicer
* Mezzaluna
* Milling cutter
* Nail clipper
* Nibbler
* Oxy-fuel cutting torch
* Pencil sharpener
* Pipecutter
* Pizza cutter
* Plasma cutter
* Plane
* Pocket knife
* Putty knife
* Rasp
* Razor
* Razor strop
* Reamer
* Sandpaper
* Saw
* Abrasive saw
* Bandsaw
* Chainsaw
* Circular saw
* Concrete saw
* Coping saw
* Fretsaw
* Hacksaw
* Hand saw
* Hole saw
* Miter saw
* Wire saw
* Scalpel
* Scissors
* Scraper
* Card
* Hand
* Paint
* Sharpening jig
* Sharpening stone
* Snips
* Steel wool
* Surform
* Switchblade
* Tool bit
* Utility knife
* Water jet cutter
* Wire brush
* Wire stripper

Types of tools
Cleaning
Cutting and abrasive
Forestry
Garden
Hand
Kitchen
Machine and metalworking
Masonry
Measuring and alignment
Mining
Power
Textile
Woodworking

* v
* t
* e

Woodworking

Overviews|

* History
* Glossary
* Wood (lumber)

Occupations|

* Boat building
* Bow and arrow
* Bush carpentry
* Cabinetry
* Caning
* Carpentry
* Certosina
* Chainsaw carving
* Chip carving
* Ébéniste
* Fretwork
* Intarsia
* Japanese carpentry
* Khatam
* Kohlrosing
* Log building
* Luthier
* Marquetry
* Millwork
* Pallet crafting
* Parquetry
* Pyrography
* Relief carving
* Root carving
* Segmented turning
* Shingle weaving
* Shipbuilding
* Spindle turning
* Timber framing
* Treen
* Whittling
* Wood carving
* Woodturning

Woods|

| Soft|

* Cedar (Calocedrus, Cedrus)
* Cypress
* Douglas fir
* Fir
* Juniper
* Larch
* Kauri
* Pine
* Rimu
* Spruce
* Yew

|

Hard|

* Afromosia
* Alder
* Andiroba
* Anigre
* Ash
* Apple
* Aspen
* Avodire
* Balsa
* Beech
* Bilinga
* Birch
* African Blackwood
* Australian Blackwood
* Boxwood
* Bubinga
* Camphor
* Cedrela
* Cherry
* Chestnut
* Cocobolo
* Cumaru
* Ebony
* Elm
* Eucalyptus
* Hazel
* Hickory
* Hornbeam
* Idigbo
* Imbuia
* Ipê
* Iroko
* Jarrah
* Jelutong
* Lignum vitae
* Linden (lime, basswood)
* Lovoa
* Merbau
* Mahogany (American, African)
* Maple
* Meranti
* Oak
* Padauk
* Pear
* Plum
* Poplar
* Purpleheart
* Ovankol
* Ramin
* Red Quebracho
* Rosewood
* Rubberwood
* Sapele
* Teak
* Totara
* Utile
* Walnut
* Wenge
* Willow
* Zebrano

Engineered|

* Cross-laminated
* Glue laminated
* Hardboard
* MDF
* OSB
* Particle board
* Plywood
* Wood-plastic composite

Tools|

* Abrasives
* Axe
* Adze
* Burnisher
* Chisel
* Drawknife
* Drill
* Fence
* Float
* Gimlet
* Gauge
* Impact driver
* Janka hardness test
* Jointer
* Mallet
* Milling machine
* Mitre box
* Rasp
* Router
* Shaper
* Sandpaper
* Square (Carpenters, Combination, Miter, Speed, Try)
* Thickness planer
* Timber-framing
* Veneer hammer
* Vise
* Warrington hammer
* Winding sticks
* Wood scribe
* Workbench

Clamps|

* Band clamp
* C-clamp
* F-clamp
* Flooring clamp
* Gripe
* Holdfast
* Mitre clamp
* Pipe clamp
* Sawbuck

Saws|

* Backsaw
* Bandsaw
* Bow
* Bucksaw
* Chainsaw
* Circular
* Compass
* Coping
* Crosscut
* Frame
* Fretsaw
* Hand saw
* Jigsaw
* Keyhole
* Miter
* Ripsaw
* Scroll
* Table
* Veneer
* Whipsaw

Planes|

* Bedrock plane
* Block plane
* Chamfer plane
* Compass plane
* Finger plane
* Fore plane
* Grooving plane
* Jack plane
* Japanese plane
* Jointer plane
* Moulding plane
* Razee plane
* Rebate plane
* Router plane
* Scrub plane
* Shoulder plane
* Smoothing plane
* Spokeshave
* Surform

Geometry|

| Joints|

* Birdsmouth
* Biscuit
* Box
* Bridle
* Butt
* Butterfly
* Coping
* Crown of thorns
* Dado
* Dovetail
* Finger
* Groove
* Halved
* Hammer-headed tenon
* Knee
* Lap
* Mason's mitre
* Miter
* Mortise and tenon
* Rabbet/Rebate
* Scarf
* Splice
* Tongue and groove

|

Profiles|

* Bead
* Bevel
* Chamfer
* Ogee
* Ogive
* Ovolo

Surface piecing|

* Binding
* Edge banding
* Intarsia
* Marquetry
* Oystering
* Parquetry
* Purfling

Treatments|

* Adhesive
* French polish
* Heat bending
* Lacquer
* Oil
* Paint
* Paint stripper
* Steam bending
* Thermal
* Varnish
* Wax
* Wood drying
* Wood preservation
* Wood stain
* Wood finishing

Organizations|

* American Association of Woodturners
* Architectural Woodwork Institute
* British Woodworking Federation
* Building and Wood Workers' International
* Caricature Carvers of America
* International Federation of Building and Wood Workers
* National Wood Carvers Association
* Society of Wood Engravers
* Timber Framers Guild

Conversion|

* Chainsaw mill
* Hewing
* Sawmill
* Whipsaw
* Wood splitting
* Flat sawing
* Quarter sawing
* Rift sawing

Techniques|

* Frame and panel
* Frameless construction
* Green woodworking

* Category
* WikiProject
* Commons

* v
* t
* e

Paper products

Containers|

* Box
* Carton
* Cigarette pack
* Coffee cup sleeve
* Corrugated box
* Corrugated fiberboard
* Envelope
* Molded pulp
* Oyster pail
* Paper bag
* Paper cup
* Paperboard
* Shipping tube

Hygiene|

* Facial tissue
* Napkin
* Paper towel
* Toilet paper
* Wet wipe

Stationery|

* Continuous stationery
* Greeting card
* Index card
* Letter
* Manila folder
* Notebook
* Postage stamp
* Postcard
* Post-it note

Financial|

* Banknote
* Business card
* Coupon
* Paper money
* Passbook
* Visiting card

Decorations|

* Ingrain wallpaper
* Mat
* Wallpaper

Media|

* Book
* Magazine
* Newspaper
* Newsprint
* Pamphlet

Recreation|

* Confetti
* Paper craft
* Paper toys
* Playing card
* Quilling

Other|

* Drink coaster
* Filter paper
* Form
* Paper model
* Sandpaper
* Security paper

* v
* t
* e

Metalworking

* v
* t
* e

Machining and computing

Computer-aided
engineering|

* 2.5D
* CAD
* CAM
* G-code
* Numerical control (NC and CNC)
* Stewart platform

Drilling and
threading|

* Die head
* Drill
* Drill bit
* Drill bit shank
* Drill bit sizes
* Drilling
* List of drill and tap sizes
* Tap and die
* Tap wrench
* Threading

Grinding and
lapping|

* Abrasive
* Abrasive machining
* Angle grinder
* Bench grinder
* Coated abrasive
* Cylindrical grinder
* Diamond plate
* Flick grinder
* Grinding
* Grinding dresser
* Grinding machine
* Grinding wheel
* Jig grinder
* Lapping
* Sanding
* Sharpening stone
* Spark testing
* Surface grinder
* Tool and cutter grinder

Machining|

* Boring
* Broaching
* Electrical discharge machining
* Electrochemical machining
* Electron-beam machining
* End mill
* Engraving
* Facing
* Hobbing
* Jig borer
* Machine tool
* Machining
* Metal lathe
* Milling
* Milling cutter
* Pantograph
* Photochemical machining
* Planer
* Reamer
* Rotary transfer machine
* Shaper
* Skiving
* Turning
* Ultrasonic machining

Machine tools|

* Angle plate
* Chuck
* Collet
* Fixture
* Indexing head
* Jig
* Lathe center
* Machine taper
* Magnetic switchable device
* Mandrel
* Rotary table
* Wiggler

Terminology|

* Cutting fluid
* Machining vibrations
* Speeds and feeds
* Swarf
* Tolerance
* Tool and die making
* Tramp oil
* Workpiece

* Casting
* Fabrication
* Forming
* Jewellery
* Machining
* Metallurgy
* Smithing
* Tools and terminology
* Welding

*[v]: View this template
*[t]: Discuss this template
*[e]: Edit this template