Table of Contents Categories
  Encyclosphere.org ENCYCLOREADER
  supported by EncyclosphereKSF

Phthalic anhydride

Topic: Chemistry

 From HandWiki - Reading time: 6 min
Phthalic anhydride
Skeletal formula of phthalic anhydride
Space-filing model
Sample of phthalic anhydride.jpg
Names
Preferred IUPAC name
2-Benzofuran-1,3-dione[1]
Other names
Isobenzofuran-1,3-dione[1]
Phthalic anhydride[1]
Identifiers
3D model (JSmol)
118515
ChEBI
ChEMBL
ChemSpider
EC Number
  • 201-607-5
27200
RTECS number
  • TI3150000
UNII
UN number 2214
Properties
C8H4O3
Molar mass 148.1 g/mol
Appearance white flakes
Odor characteristic, acrid[2]
Density 1.53 g/cm3, solid; 1.20 g/mL, molten[2]
Melting point 131.6 °C (268.9 °F; 404.8 K)
Boiling point 295 °C (563 °F; 568 K) sublimates
0.62 g/100g (20—25 °C);
19.0 g/100g (100 °C);
reacts slowly
Vapor pressure 0.0015 mmHg (20 °C)[2]
−67.31×10−6 cm3/mol
Hazards
GHS pictograms GHS05: CorrosiveGHS07: HarmfulGHS08: Health hazard
GHS Signal word Danger
H302, H315, H317, H318, H334, H335
P261, P264, P270, P271, P272, P280, P285, P301+312, P302+352, P304+340, P304+341, P305+351+338, P310, P312, P321, P330, P332+313, P333+313, P342+311, P362, P363, P403+233, P405, P501
NFPA 704 (fire diamond)
Flammability code 1: Must be pre-heated before ignition can occur. Flash point over 93 °C (200 °F). E.g. canola oilHealth code 3: Short exposure could cause serious temporary or residual injury. E.g. chlorine gasReactivity code 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g. liquid nitrogenSpecial hazards (white): no codeNFPA 704 four-colored diamond
1
3
0
Flash point 152 °C (306 °F; 425 K)
Explosive limits 1.7%–10.5%
Lethal dose or concentration (LD, LC):
4020 mg/kg (oral, rat)
1520 mg/kg (oral, mouse)
800 mg/kg (oral, cat)
800–1600 mg/kg (oral, rat)
2210 mg/kg (oral, mouse)[3]
NIOSH (US health exposure limits):
PEL (Permissible)
 TWA 12 mg/m3 (2 ppm)[2]
REL (Recommended)
 TWA 6 mg/m3 (1 ppm)[2]
IDLH (Immediate danger)
 60 mg/m3[2]
Related compounds
Related compounds
 Phthalic acid
Phthalimide
Phthalide
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
☒N verify (what is ☑Y☒N ?)
Infobox references

Phthalic anhydride is the organic compound with the formula C6H4(CO)2O. It is the anhydride of phthalic acid. Phthalic anhydride is a principal commercial form of phthalic acid. It was the first anhydride of a dicarboxylic acid to be used commercially. This white solid is an important industrial chemical, especially for the large-scale production of plasticizers for plastics. In 2000, the worldwide production volume was estimated to be about 3 million tonnes per year.[4]

Synthesis and production

Phthalic anhydride was first reported in 1836 by Auguste Laurent. Early procedures involved liquid-phase mercury-catalyzed oxidation of naphthalene.[5] The modern industrial variant process instead uses vanadium pentoxide (V2O5) as the catalyst in a gas-phase reaction with naphthalene using molecular oxygen.[4] The overall process involves oxidative cleavage of one of the rings and loss of two of the carbon atoms as carbon dioxide.

An alternative process involves oxidation of the two methyl groups of o-xylene, a more atom-economical process. This reaction is run at about 320–400 °C and has the following stoichiometry:

C6H4(CH3)2 + 3 O2 → C6H4(CO)2O + 3 H2O

The reaction proceeds with about 70% selectivity. About 10% of maleic anhydride is also produced:

C6H4(CH3)2 + 7+1/2 O2 → C4H2O3 + 4 H2O + 4 CO2

Phthalic anhydride and maleic anhydride are recovered by distillation by a series of switch condensers.

The naphthalene route (the Gibbs phthalic anhydride process or the Gibbs–Wohl naphthalene oxidation reaction) has declined relative to the o-xylene route.

Proposed early steps in vanadium-catalyzed oxidation of naphthalene to phthalic anhydride, with V2O5 represented as a molecule versus its true extended structure.[6]

Phthalic anhydride can also be prepared from phthalic acid by simple thermal dehydration above 210°C.[4]

Uses

Phthalate esters plasticizers

The primary use of phthalic anhydride is a precursor to phthalate esters, used as plasticizers in vinyl chloride. Phthalate esters are derived from phthalic anhydride by the alcoholysis reaction.[4] In the 1980s, approximately 6.5 million tonnes of these esters were produced annually, and the scale of production was increasing each year, all from phthalic anhydride. The process begins with the reaction of phthalic anhydride with alcohols, giving the monoesters:

C6H4(CO)2O + ROH → C6H4(CO2H)CO2R

The second esterification is more difficult and requires removal of water:

C6H4(CO2H)CO2R + ROH ⇌ C6H4(CO2R)2 + H2O

The most important diester is bis(2-ethylhexyl) phthalate ("DEHP"), used in the manufacture of polyvinyl chloride compounds.

Precursor to dyestuffs

Quinoline Yellow SS is a popular dye derived from the condensation of phthalic anhydride and 2-methylquinoline.

Phthalic anhydride is widely used in industry for the production of certain dyes. A well-known application of this reactivity is the preparation of the anthraquinone dye quinizarin by reaction with para-chlorophenol followed by hydrolysis of the chloride.[7] Phenolphthalein can be synthesized by the condensation of phthalic anhydride with two equivalents of phenol under acidic conditions (hence the name). It was discovered in 1871 by Adolf von Baeyer.[8][9][10]

Synthesis of phenolphthalein[11]

Pharmaceuticals

Phthalic anhydride treated with cellulose acetate gives cellulose acetate phthalate (CAP), a common enteric coating excipient that has also been shown to have antiviral activity.[12] Phthalic anhydride is a degradation product of CAP.[13]

Reactions

Phthalic anhydride is a versatile intermediate in organic chemistry, in part because it is bifunctional and cheaply available.

Hydrolysis, alcoholysis, ammonolysis

Hydrolysis by hot water forms ortho-phthalic acid:[14]

C6H4(CO)2O + H2O → C6H4(CO2H)2

Hydrolysis of anhydrides is not typically a reversible process. Phthalic acid is however easily dehydrated to form phthalic anhydride. Above 180 °C, phthalic anhydride re-forms.

Chiral alcohols form half-esters (see above), and these derivatives are often resolvable because they form diastereomeric salts with chiral amines such as brucine.[15] A related ring-opening reaction involves peroxides to give the useful peroxy acid:[16]

C6H4(CO)2O + H2O2 → C6H4(CO3H)CO2H

Phthalimide can be prepared by heating phthalic anhydride with aqueous ammonia giving a 95–97% yield. Alternatively, it may be prepared by treating the anhydride with ammonium carbonate or urea. It can also be produced by ammoxidation of o-xylene.[4] Potassium phthalimide is commercially available and is the potassium salt of phthalimide. It may be prepared by adding a hot solution of phthalimide to a solution of potassium hydroxide; the desired product precipitates.[17]

Preparation of aliphatic nitroalkenes

Phthalic anhydride is used to dehydrate short-chain nitro-alcohols to yield nitroalkenes, compounds with a high tendency to polymerize.[18]

Safety

The most probable human exposure to phthalic anhydride is through skin contact or inhalation during manufacture or use. Studies show that exposure to phthalic anhydride can cause rhinitis, chronic bronchitis, and asthma. Phthalic anhydride's reaction on human health is generally an asthma–rhinitis–conjunctivitis syndrome or a delayed reaction and influenza-like symptoms and with increased immunoglobulin (E and G) levels in the blood.

References

  1. ↑ 1.0 1.1 1.2 "Front Matter". Nomenclature of Organic Chemistry : IUPAC Recommendations and Preferred Names 2013 (Blue Book). Cambridge: The Royal Society of Chemistry. 2014. p. 835. doi:10.1039/9781849733069-FP001. ISBN 978-0-85404-182-4. 
  2. ↑ 2.0 2.1 2.2 2.3 2.4 2.5 NIOSH Pocket Guide to Chemical Hazards. "#0512". National Institute for Occupational Safety and Health (NIOSH). https://www.cdc.gov/niosh/npg/npgd0512.html. 
  3. ↑ "Phthalic anhydride". Immediately Dangerous to Life and Health Concentrations (IDLH). National Institute for Occupational Safety and Health (NIOSH). https://www.cdc.gov/niosh/idlh/85449.html. 
  4. ↑ 4.0 4.1 4.2 4.3 4.4 Lorz, Peter M.; Towae, Friedrich K.; Enke, Walter; Jäckh, Rudolf; Bhargava, Naresh; Hillesheim, Wolfgang (2007). "Ullmann's Encyclopedia of Industrial Chemistry". Ullmann's Encyclopedia of Industrial Chemistry. Weinheim: Wiley-VCH. doi:10.1002/14356007.a20_181.pub2. 
  5. ↑ Laurent, Aug. (1836). "Sur l'acide naphtalique et ses combinaisons" (in French). Annales de Chimie et de Physique. 2nd series 61: 113–125. https://babel.hathitrust.org/cgi/pt?id=hvd.hx3dwy&view=1up&seq=119. 
  6. ↑ "Gibbs-Wohl Naphthalene Oxidation". Comprehensive Organic Name Reactions and Reagents. 2010. doi:10.1002/9780470638859.conrr270. ISBN 9780470638859. 
  7. ↑ L. A. Bigelow and H. H. Reynolds (1941). "Quinizarin". Organic Syntheses. http://www.orgsyn.org/demo.aspx?prep=CV1P0476. ; Collective Volume, 1, pp. 476 
  8. ↑ Baeyer, A. (1871). "Ueber eine neue Klasse von Farbstoffen". Berichte der Deutschen Chemischen Gesellschaft 4 (2): 555–558. doi:10.1002/cber.18710040209. https://zenodo.org/record/1425008. 
  9. ↑ Baeyer, A. (1871). "Ueber die Phenolfarbstoffe". Berichte der Deutschen Chemischen Gesellschaft 4 (2): 658–665. doi:10.1002/cber.18710040247. https://zenodo.org/record/1425010. 
  10. ↑ Baeyer, A. (1871). "Ueber die Phenolfarbstoffe". Polytechnisches Journal 201 (89): 358–362. http://dingler.culture.hu-berlin.de/article/pj201/ar201089. 
  11. ↑ Max Hubacher, U.S. Patent 2,192,485 (1940 to Ex Lax Inc)
  12. ↑ "Microbicide for prevention of sexually transmitted diseases using a pharmaceutical excipient.". AIDS Patient Care STDs 14 (4): 215–9. 2000. doi:10.1089/108729100317830. PMID 10806641. 
  13. ↑ "Development of a gel permeation chromatographic assay to achieve mass balance in cellulose acetate phthalate stability studies.". J Pharm Biomed Anal 49 (2): 240–6. 2009. doi:10.1016/j.jpba.2008.10.039. PMID 19070984. 
  14. ↑ Noller, Carl R. (1965). Chemistry of Organic Compounds (3rd ed.). Philadelphia: W. B. Saunders. pp. 602. 
  15. ↑ Joseph Kenyon (1941). "d- and l-Octanol-2". Organic Syntheses. http://www.orgsyn.org/demo.aspx?prep=CV1P0418. ; Collective Volume, 1, pp. 418 
  16. ↑ George B. Payne (1973). "Monoperphthalic acid". Organic Syntheses. http://www.orgsyn.org/demo.aspx?prep=CV5P0805. ; Collective Volume, 5, pp. 805 
  17. ↑ P. L. Salzberg and J. V. Supniewski (1941). "β-Bromoethylphthalimide". Organic Syntheses. http://www.orgsyn.org/demo.aspx?prep=cv1p0119. ; Collective Volume, 1, pp. 119 
  18. ↑ Ranganathan, Darshan; Rao, Bhushan; Ranganathan, Subramania et al. (1980). "Nitroethylene: a stable, clean, and reactive agent for organic synthesis". The Journal of Organic Chemistry 45 (7): 1185–1189. doi:10.1021/jo01295a003. 

External links



Retrieved from "https://handwiki.org/wiki/index.php?title=Chemistry:Phthalic_anhydride&oldid=3332880"
Licensed under CC BY-SA 3.0 | Source: https://handwiki.org/wiki/Chemistry:Phthalic_anhydride
3 views | Status: cached on September 05 2024 06:03:04
↧ Download this article as ZWI file
Encyclosphere.org EncycloReader is supported by the EncyclosphereKSF