Raman scattering or the Raman effect is the inelastic scattering of a photon.
When light is scattered from an atom or molecule, most photons are elastically scattered (Rayleigh scattering). The scattered photons have the same energy (frequency) and wavelength as the incident photons. However, a small fraction of the scattered light (approximately 1 in 1 million photons) is scattered by an excitation, with the scattered photons having a frequency different from, and usually lower than, the frequency of the incident photons.[1] In a gas, Raman scattering can occur with a change in vibrational, rotational or electronic energy of a molecule (see energy level). Chemists are concerned primarily with the vibrational Raman effect.
In 1922, Indian physicist Chandrasekhara Venkata Raman published his work on the "Molecular Diffraction of Light," the first of a series of investigations with his collaborators which ultimately led to his discovery (on 28 February 1928) of the radiation effect which bears his name. The Raman effect was first reported by C. V. Raman and K. S. Krishnan, and independently by Grigory Landsberg and Leonid Mandelstam, in 1928. Raman received the Nobel Prize in 1930 for his work on the scattering of light. In 1998[2] the Raman Effect was designated an ACS National Historical Chemical Landmark in recognition of its significance as a tool for analyzing the composition of liquids, gases, and solids.[3]
The interaction of light with matter in a linear regime allows the absorption or simultaneous emission of light precisely matching the difference in energy levels of the interacting electrons.
The Raman effect corresponds, in perturbation theory, to the absorption and subsequent emission of a photon via an intermediate electron state, having a virtual energy level (see also: Feynman diagram). There are three possibilities:
These differences in energy are measured by subtracting the energy of the mono-energetic laser light from the energy of the scattered photons. The absolute value, however, doesn't depend on the process (Stokes or anti-Stokes scattering), because only the energy of the different vibrational levels is of importance. Therefore, the Raman spectrum is symmetric relative to the Rayleigh band. In addition, the intensities of the Raman bands are only dependent on the number of molecules occupying the different vibrational states, when the process began. If the sample is in thermal equilibrium, the relative numbers of molecules in states of different energy will be given by the Boltzmann distribution:
<math>\frac{\ N_1}{N_0} = \frac{\ g_1}{g_0} e^{-\frac{\Delta E_v}{kT}}</math>
|
Thus lower energy states will have more molecules in them than will higher (excited) energy states. Therefore, the Stokes spectrum will be more intense than the anti-Stokes spectrum.
The Raman effect differs from the process of fluorescence. For the latter, the incident light is completely absorbed and the system is transferred to an excited state from which it can go to various lower states only after a certain resonance lifetime. The result of both processes is essentially the same: A photon with the frequency different from that of the incident photon is produced and the molecule is brought to a higher or lower energy level. But the major difference is that the Raman effect can take place for any frequency of the incident light. In contrast to the fluorescence effect, the Raman effect is therefore not a resonant effect.
The distortion of a molecule in an electric field, and therefore the vibrational Raman cross section, is determined by its polarizability.
A Raman transition from one state to another, and therefore a Raman shift, can be activated optically only in the presence of non-zero polarizability derivative with respect to the normal coordinate (that is, the vibration or rotation):
<math>\left | \frac {\partial \alpha}{\partial Q} \right | > 0</math>
Raman-active vibrations/rotations can be identified by using almost any textbook that treats quantum mechanics or group theory for chemistry. Then, Raman-active modes can be found for molecules or crystals that show symmetry by using the appropriate character table for that symmetry group.
Raman amplification can be obtained by using Stimulated Raman Scattering (SRS), which actually is a combination between a Raman process with stimulated emission. It is interesting for application in telecommunication fibers to amplify inside the standard material with low noise for the amplification process. However, the process requires significant power and thus imposes more stringent limits on the material. The amplification band can be up to 100 nm broad, depending on the availability of allowed photon states.
For high intensity CW (continuous wave) lasers, SRS can be used to produce broad bandwidth spectra. This process can also be seen as a special case of four wave mixing, where the frequencies of the two incident photons are equal and the emitted spectra are found in two bands separated from the incident light by the phonon energies. The initial Raman spectrum is built up with spontaneous emission and is amplified later on. At high pumping levels in long fibers, higher order Raman spectra can be generated by using the Raman spectrum as a new starting point, thereby building a chain of new spectra with decreasing amplitude. The disadvantage of intrinsic noise due to the initial spontaneous process can be overcome by seeding a spectrum at the beginning, or even using a feedback loop like in a resonator to stabilize the process. Since this technology easily fits into the fast evolving fiber laser field and there is demand for transversal coherent high intensity light sources (i.e. broadband telecommunication, imaging applications), Raman amplification and spectrum generation might be widely used in the near future.
Raman spectroscopy employs the Raman effect for materials analysis. The frequency of light scattered from a molecule may be changed based on the structural characteristics of the molecular bonds. A monochromatic light source (laser) is required for illumination, and a spectrogram of the scattered light then shows the deviations caused by state changes in the molecule.
Raman spectroscopy is also used in combustion diagnostics. Being a completely non-intrusive technique, it permits the detection of the major species and temperature distribution inside combustors and in flames without any perturbation of the (mainly fluid dynamic and reactive) processes examined.
Stimulated Raman transitions are also widely used for manipulating a trapped ion's energy levels, and thus basis qubit states.
cs:Ramanův jev de:Ramanstreuung el:Σκέδαση Raman fa:پراش رامان it:Effetto Raman fi:Ramansironta sv:Ramanspridning uk:Раманівське розсіювання