Bearings

Bearings. In engineering a “bearing” is that particular kind of support which, besides carrying the load imposed upon it by the shaft associated with it, allows the shaft freedom to revolve. Or, put in another way, a bearing forms with the shaft a pair of elements having one degree of freedom to turn relatively to one another about their common axis. The part of the shaft in the bearing is commonly called the journal. The component parts of a small bearing, pillow block, plummer block or pedestal, as it is variously styled, are illustrated in fig. 1, and these parts, put together, are further illustrated in fig. 2 with the shaft added. Corresponding parts are similarly lettered in the two illustrations. The shaft (S) is encircled by the brasses (B1 and B2) made of gun metal, phosphor bronze or other suitable material. The lower brass fits into the main casting (A) in the semicircular seat provided for it, and is prevented from moving endways by the flanges (F, F) and from turning with the shaft by the projections (P, P), which fit into corresponding recesses in the casting (A), one of which is shown at p. After the shaft has been placed in position, the upper brass (B2) and the cap (C) are put on and both are held in place by the bolts (Q1, Q2). The brasses are bedded into the main casting (A) and the cap (C) respectively at the surfaces D, D, D, D. The complete bearing is held to the framework of the machine by bolts (R1, R2) passing through holes (H, H) which are slotted to allow endwise adjustment of the whole bearing in order to facilitate the alignment of the shaft. Oil or other lubricant is introduced through the hole (G), and it passes through the top brass to grooves or oilways cut into the surface of the brass for the purpose of distributing the oil uniformly to the journal.

Fig. 1.

Some form of lubricator is usually fitted at G in order to supply oil to the bearing continuously. A form of lubricator used for this purpose is shown in place, fig. 2, and an enlarged section is shown in fig. 3. It will be seen that the lubricator consists essentially of a cup the base of which is pierced centrally by a tube which reaches to within a small distance of the lid of the cup inside, and projects into the oilway leading to the journal outside. The annular space round the tube inside is filled with oil which is transferred to the central tube and thence to the bearing by the capillary action of a cotton wick thrust down on a piece of wire. It is only necessary to withdraw the wick from the central tube to stop the supply of oil. The lubricator is fitted through a hole in the lid which is usually plugged with a piece of cane or closed by more elaborate means. A line of shafting would be supported by several bearings of the kind illustrated, themselves supported by brackets projecting from or rigidly fixed to the walls of the workshop, or on frames resting on the floor, or on hangers attached to the roof girders or principals.

Fig. 2.

Fig. 3.

In bearings of modern design for supporting a line shaft the general arrangement shown in fig. 1 is modified so that the alignments of the shaft can be made both vertically or horizontally by means of adjusting screws, and the brass is jointed with the supporting main body so that it is free to follow the small deflections of the shaft which take place when the shaft is working. Another modern improvement is the formation of an oil reservoir or well in the base of the bearing itself, and the transference of the oil from this well to the shaft by means of one or two rings riding loosely on the shaft. The bottom part of the ring dips into the oil contained in the well of the bearing and, as the shaft rotates, the ring rolls on the shaft and thus carries oil up to the shaft continuously, from which it finds its way to the surfaces of the shaft and bearing in contact. It should be understood that the upper brass is slotted crossways to allow the ring to rest on the shaft. When the direction of the load carried by the bearing is constant it is unnecessary to provide more than one brass, and the construction is modified accordingly. Figs. 4 and 5 show an axle box used for goods wagons on the Great Eastern railway, and they also illustrate the method of pad lubrication in general use for this kind of bearing. The main casting, A, is now uppermost, and is designed so that the upper part supports and constrains the spring buckle through which the load W is transmitted to the bearing, and the lower part inside is arranged to support the brass, B. The brass is jointed freely with the main casting by means of a hemispherical hump resting in a corresponding recess in the casting. What may be called the cap, C, forms the lower part of the axle box, but instead of supporting a second brass it is formed into an oil reservoir in which is arranged a pad of cotton wick woven on a tin frame. The upper part of the pad is formed into a kind of brush, shaped to fit the underside of the journal, whilst the lower part consists of streamers of wick resting in the oil. The oil is fed to the brush by the capillary action of the streamers. The reservoirs are filled with oil through the apertures P and O. The bottom cap is held in position by the T-headed bolts Q1 and Q2 (fig. 5). By slackening the nuts and turning the T-heads fair with the slots in the cap, the cap comes right away and the axle may be examined. A leather ring L is fitted as shown to prevent dust from entering the axle box.

Fig. 4.

Fig. 5.

Fig. 6.

Footsteps.—A bearing arranged to support the lower end of a vertical shaft is called a footstep, sometimes a pivot bearing. A simple form of footstep is shown in fig 6. A casting A, designed so that it can be conveniently bolted to a foundation block, cross beam, or bracket is bored out and fitted with a brass B, which is turned inside to carry the end of the shaft S. The whole vertical load on the shaft is carried by the footstep, so that it is important to arrange efficient lubricating apparatus. Results of experiments made on a footstep, reported in Proc. Inst. Mech. Eng., 1891, show that if a diametral groove be cut in the brass, as indicated at g (fig 6), and if the oil is led to the centre of this groove by a channel c communicating with the exterior, the rotation of the shaft draws in a plentiful supply of oil which radiates from the centre and makes its way vertically between the shaft and the brass and finally overflows at the top of the brass. The overflowing oil may be led away and may be re-introduced into the footsteps at c. The rotation of the shaft thus causes a continuous circulation of oil through the footstep. One experiment from the report mentioned above may be quoted. A 3-in. shaft, revolving 128 times per minute and supported on a manganese bronze bearing lubricated in the way explained above sustained increasing loads until, at a load of 300 pounds per square inch of the area of the end of the shaft, it seized. The mechanical details of a footstep may be varied for purposes of adjustment in a variety of ways similarly to the variations of a common bearing already explained.

Thrust Block Bearing.—In cases where a bearing is required to resist a longitudinal movement of the shaft through it, as for example in the case of the propeller shaft of a marine engine or a vertical shaft supporting a heavy load not carried on a footstep, the shaft is provided with one or more collars which are grooved with corresponding recesses in the brasses of the bearing. A general sketch of a thrust block for a propeller shaft is shown in fig. 7. There are seven collars turned on the shaft and into the circumferential grooves between them fit corresponding circumferential projections on the brasses, these projections being formed in the case illustrated by means of half rings which are fitted into grooves turned in the brasses. This method of construction allows an individual ring to be replaced or adjusted if it should get hot. The total area of the rubbing surfaces should be proportioned so that the average load is not more than from 50 to 70 ℔ per sq. in. Arrangements are usually made for cooling a thrust block with water in case of heating. The spindles of drilling machines, boring machine spindles, turbine shafts may be cited as examples of vertical shafts supported on one collar. Experiments on the friction of a collar bearing have been made by the Research Committee of the Institution of Mechanical Engineers (Proc. Inst. Mech. Eng., 1888).

Fig. 7.

Roller and Ball Bearings.—If rollers are placed between two surfaces having relative tangential motion the frictional resistance to be overcome is the small resistance to rolling. The rollers move along with a velocity equal to one half the relative velocity of the surfaces. This way of reducing frictional resistance has been applied to all kinds of mechanical contrivances, including bearings for shafts, railway axle boxes, and axle boxes for tramcars. An example of a roller bearing for a line shaft is illustrated in figs. 8 and 9. The main casting, A, and cap, C, bolted together, form a spherical seating for the part of the bearing E corresponding to the brasses in a bearing of the usual type. Between the inside of the casting E and the journal are placed rollers held in position relatively to one another by a “squirrel cage” casting, the section of the bars of which are clearly shown in the half sectional elevation, fig. 9. This squirrel cage ensures that the several axes of the rollers keep parallel to the axis of the journal during the rolling motion. The rollers are made of hard tool steel, and the surfaces of the journal and bearing between which they roll are hardened.

Fig. 8.	Fig. 9.

Two rings of balls may be used instead of a single ring of rollers, and the kind of ball bearing thus obtained is in general use principally in connexion with bicycles and motor cars (see Bicycle). In ball bearings the load is concentrated at a few points, the points where the balls touch the race, and in the roller bearing at a few lines, the lines of contact between the rollers and the surfaces of the journal and bearing; consequently the load which bearings of this kind carry must not be great enough to cause any indentation at the points or lines of contact. Both rollers and balls, and the paths on which they roll, therefore, are made of hard material; further, balls and rollers must all be exactly the same size in an individual bearing in order to distribute the load between the points or lines of contact as uniformly as possible. The finest workmanship is required therefore to make good roller or good ball bearings.

Fig. 10.

Bearings for High Speeds and Forced Lubrication.—When the shaft turns the metallic surfaces of the brass and the journal are prevented from actual contact by a film of oil which is formed and maintained by the motion of the shaft and which sustains the pressure between the journal and the brass provided the surfaces are accurately formed and the supply of oil is unlimited. This film changes what would otherwise be the friction between metallic surfaces into a viscous resistance within the film itself. When through a limited supply of oil or imperfect lubrication this film is imperfect or fails altogether and allows the journal to make metallic contact with the brass, the friction increases; and it may increase so much that the bearing rapidly becomes hot and may ultimately seize, that is to say the rubbing surfaces may become stuck together. With the object of reducing the friction at the points of metallic contact and of confining the damage of a hot bearing to the easily renewable brass, the latter is partially, sometimes wholly, lined with a soft fusible metal, technically known as white metal, which melts away before actual seizure takes place, and thus saves the journal which is more expensive because it is generally formed on a large and expensive shaft. However perfectly the film fulfils its function, the work required to overcome the viscous resistance of the film during the continuous rotation of the shaft appears as heat, and in consequence the temperature of the bearing gradually rises until the rate at which heat is produced is equal to the rate at which it is radiated from the bearing. Hence in order that a journal may revolve with a minimum resistance and without undue heating two precautions must be taken: (1) means must be taken to ensure that the film of oil is complete and never fails; and (2) arrangements must be made for controlling the temperature should it rise too high. The various lubricating devices already explained supply sufficient oil to form a partial film, since experiments have shown that the friction of bearings lubricated in this way is akin to solid friction, thus indicating at least partial metallic contact. In order to supply enough oil to form and maintain a film with certainty the journal should be run in an oil bath, or oil should be supplied to the bearing under pressure sufficient to force it in between the surfaces against the load. A bearing to which forced lubrication and water cooling are applied is illustrated in fig. 10, which represents one of the bearings of a Westinghouse turbo-alternator installed at the power station of the Underground Electric Railways Company of London at Lots Road, Chelsea. Oil flows under pressure from a tank on the top of a tower along a supply pipe to the oil inlet O, and after passing through the bearing and performing its duty as a film it falls away from each end of the journal into the bottom of the main casting, from which a pipe, E, conveys the oil back to the base of the tank tower where it is cooled and finally pumped back into the tank. There is thus a continuous circulation of oil through the bearing. The space C is for cooling water; in fact the bearing is water jacketed and the jacket is connected to a supply pipe and a drain pipe so that a continuous circulation may be maintained if desired. This bearing is 12 in. in diameter and 48 in. long, and it carries a load of about 12.8 tons. The rise in temperature of the bearing under normal conditions of working without water circulating in the jacket is approximately 38° F. The speed of rotation is such that the surface velocity is about 50 ft. per second.

Forced lubrication in connexion with the bearings of high-speed engines was introduced in 1890 by Messrs Belliss & Morcom, Ltd., under patents taken out in the name of A.C. Pain. It should be understood that providing the film of oil in the bearing of an engine can be properly maintained a double-acting engine can be driven at a high speed without any knocking, and without perceptible wear of the rubbing surfaces. Fig. 11 shows that the general arrangement of the bearings of a Belliss & Morcom engine arranged for forced lubrication. A small force-pump F, driven from the eccentric strap X, delivers oil into the pipe P, along which it passes to A, the centre of the right-hand main bearing. There is a groove turned on the inside of the brass from which a slanting hole leads to B. The oil when it arrives at A thus has two paths open to it, one to the right and left of the groove through the bearing, the other along the slanting hole to B. At B it divides again into two streams, one stream going upwards to the eccentric sheave, and a part continuing up the pipe Q to the eccentric pin. The second stream from B follows the slanting hole in the crank shaft to C, where it is led to the big end journal through the pipe R to the crosshead pin, and through the slanting hole to D, where it finds its way into the left main bearing. The oil forced through each bearing falls away to the right and to the left of the journal and drops into the bottom of the engine framing, whence it is again fed to the pump through a strainer. The parts of an engine lubricated in this way must be entirely enclosed.

Fig. 11.

Load on bearings.—The distribution of pressure over the film of lubricant separating the rubbing surfaces of a bearing is variable, being greatest at a point near but not at the crown of the brass, and falling away to zero in all directions towards the boundaries of the film. It is usual in practice to ignore this variation of pressure through the film, and to indicate the severity with which the bearing is loaded by stating the load per square inch of the rubbing surfaces projected on to the diametral plane of the journal. Thus the projected area of the surfaces of a journal 6 in. in diameter and 8 in. long is 48 sq. in., and if the total load carried by the bearing is 20,000 pounds, the bearing would be said to carry a load of 417 pounds per square inch. When a shaft rotates in a bearing continuously in one direction the load per square inch with which it is safe to load the bearing in order to avoid undue heating is much less than if the motion is intermittent. A table of a few values of the bearing loads used in practice is given in the article Lubricants.

---